4-247-936-12(1) Super Audio CD/ DVD RECEIVER Operating instructions US Mode d’emploi FR AVD-C700ES ©2003 Sony Corporation
3 WARNING Caution – The use of optical instruments with this product will increase eye hazard. For the customers in the U.S.A To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Precautions Safety • If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further. • The unit is not disconnected from the mains as long as it is connected to the mains outlet, even if the unit itself has been turned off. • Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
On adjusting volume Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played. On cleaning Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.
Table of Contents Welcome! ................................................ 3 Precautions .............................................. 3 About this Manual................................... 7 This receiver Can Play the Following Discs ................................................. 7 Terms for discs........................................ 7 Notes about Discs ................................... 9 Guide to the Control Menu Display...... 11 Getting Started Unpacking .......................................
Additional Information Troubleshooting .................................... 81 Specifications........................................ 84 Glossary ................................................ 85 Index to Parts and Controls................... 89 Language Code List .............................. 93 DVD Setup Menu List .......................... 94 Index .....................................................
About this Manual Format of discs Disc logo Audio CD • The instructions in this manual describe the controls on the remote. You can also use the controls on the receiver if they have the same or similar names as those on the remote. • The following symbols are used in this manual.
Disc DVD structure Title Chapter VIDEO CD, Super Audio CD, or CD structure Disc Track Region code Index Disc MP3 structure Album Track Disc JPEG structure Album File Note on PBC (Playback Control) (VIDEO CDs) This receiver conforms to Ver. 1.1 and Ver. 2.0 of VIDEO CD standards. You can enjoy two kinds of playback depending on the disc type. Disc type You can VIDEO CDs without PBC functions (Ver. 1.1 discs) Enjoy video playback (moving pictures) as well as music.
Do not load the following discs: • A DVD with a different region code (page 8, 87). • A disc that is neither standard nor circular (e.g., card, heart, or star shape). • A disc with paper or stickers on it. • A disc that has adhesive or cellophane tape still left on it.
• Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs. This receiver can only play back a standard circular disc. Using neither standard nor circular discs (e.g., card, heart, or star shape) may cause a malfunction. Do not use a disc that has a commercially available accessory attached, such as a label or ring.
Guide to the Control Menu Display Use the Control Menu to select a function that you would like to use. The Control Menu display appears when the DVD DISPLAY button is pressed. For details, refer to the page in parentheses. Total number of Currently playing title number (Video CD/ titles or tracks recorded Total number of chapters or indexes recorded Super Audio CD/CD: track number) Currently playing Disc number and title name Playback status name or disc type (NPlayback, XPause, xStop, etc.
ALBUM (JPEG only) (page 30, 38) Selects the album (JPEG) to be played. FILE (JPEG only) (page 30, 38) Selects the file (JPEG) to be played. DATE (JPEG only) (page 44) Displays the date information. ANGLE (DVD only) (page 54) Changes the angle. PLAYMODE (page 32, 35) Selects the play mode. REPEAT (page 36) Plays the entire disc (all titles/all tracks), one title/chapter/ track/album, or contents of program repeatedly. PICTURE MODE (DVD/ Adjusts the video signal from the receiver in various ways.
Getting Started Check that you have the following items: • AM loop antenna (1) • FM wire antenna (1) • S Video cord (1) • Remote Commander (remote) RM-CL700M (1) • R6 (size AA) batteries (2) • Operating instructions (1) You can control the receiver using the supplied remote. Insert two R6 (size AA) batteries by matching the 3 and # ends on the batteries to the markings inside the compartment. When using the remote, point it at the remote sensor on the receiver.
Step 1: Speaker System Hookup You can enjoy surround sound by connecting 6 speakers (front L/R speakers, center speaker, surround L/R speakers, surround back speaker) and active subwoofer to the receiver. If you do not connect 6 speakers and active subwoofer to the receiver, the receiver offers the means to optimize the signal depending on the number of connected speakers. When you connect 2 speakers to the receiver, connect the speakers to the SPEAKERS FRONT L/R jacks.
Terminals for connecting the speakers To the Front speakers SPEAKERS FRONT L and R terminals Surround speakers SPEAKERS SURROUND L and R terminals Surround back speaker SPEAKERS SURROUND BACK terminal Center speaker SPEAKERS CENTER terminal Subwoofer SUBWOOFER AUDIO OUT jack Getting Started Connect AUDIO OUT Y PB/CB PR/CR S VIDEO OUT S VIDEO IN S VIDEO IN S VIDEO IN VIDEO OUT VIDEO IN VIDEO IN VIDEO IN COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO 2 VIDEO 1 MONITOR TV/SAT VIDEO 2 VIDEO 1
Note for connecting the speaker cords to the receiver Remove about 10 mm (3/8 inch) of insulation at the end of the cord, then twist the exposed wires. Connect the stripped ends of the cords to the terminals, taking care to avoid contact between the cords. Make sure the cords are firmly connected to the speaker and receiver terminals. 10 mm (3/8 in.) To avoid short-circuiting the speakers Short-circuiting of the speakers may damage the receiver.
Step 2: Antenna Hookups Getting Started Connect the supplied AM/FM antennas for listening to the radio.
If you have poor FM reception Use a 75-ohms coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below. Outdoor FM antenna Receiver ANTENNA FM 75 COAXIAL AM Earth wire (not supplied) To earth Note If you connect the receiver to an outdoor antenna, ground it to protect against lightning. To prevent a gas explosion, do not connect the earth wire to a gas pipe.
Step 3: TV and Video Component Hookups Getting Started Required cords S Video cord for connecting a TV monitor Audio/Video cords (not supplied) When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components.
TV with COMPONENT VIDEO IN jacks TV with S VIDEO IN jack COMPONENT VIDEO IN Y TV INPUT INPUT S VIDEO IN VIDEO IN PB/CB PR/CR IN IN IN AUDIO OUT PB/CB Y PR/CR S VIDEO OUT S VIDEO IN S VIDEO IN S VIDEO IN VIDEO OUT VIDEO IN VIDEO IN VIDEO IN COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO 2 VIDEO 1 MONITOR TV/SAT VIDEO 2 VIDEO 1 ANTENNA TV/SAT BACK R SURROUND L R CENTER SPEAKERS L FRONT IMPEDANCE USE 4-16 SUB WOOFER COMPONENT VIDEO IN FM 75 COAXIAL Y AM TV/SAT PB/CB PR/CR TV/SA
Step 4: Connecting the AC Power Cord (mains lead) Getting Started Before connecting the AC power cord (mains lead) of this receiver to a wall outlet (mains), connect the speakers to the receiver (see page 14).
When color irregularity occurs on the TV Speaker Setup For the best possible surround sound, all the speakers other than the subwoofer should be the same distance from the listening position (A). However, this receiver allows you to place the center speaker up to 1.5 metres a) closer (B) and the surround and the surround back speakers up to 4.5 metres b) closer (C, D) to the listening position. The front speakers can be placed from 0.9 to 6.9 metres c) (A) from the listening position.
4 Playing Discs Press Z on the receiver or OPEN/ CLOSE on the remote, and place a disc with the label side up on the disc tray. Playing Discs The receiver automatically turns on and the STANDBY indicator turns off. Playing Discs Playback side facing down Depending on the DVD or VIDEO CD, some operations may be different or restricted. Refer to the operation details supplied with your disc.
To turn on the receiver Press POWER on the receiver. The receiver enters standby mode and the STANDBY indicator lights up in red. Press "/1 on the remote. The receiver turns on and the STANDBY indicator turns off. In standby mode, the receiver also turns on by pressing Z, DISC 1-DISC 5, or FUNCTION –/+ on the receiver or by pressing H. To turn off the receiver Additional operations Cursor key DISC ./> Press "/1 on the remote. The receiver enters standby mode and the STANDBY indicator lights up in red.
Notes Replacing Discs While Playing a Disc You can open the disc tray while playing a disc, to check what discs are to be played next or replace discs without interrupting play of the current disc. DISC SKIP Playing Discs • Do not push the disc tray when closing it. Press Z on the receiver or OPEN/CLOSE on the remote to close the disc tray. • If DVD playback is paused for approximately one hour, the receiver automatically turns off. VOLUME POWER STANDBY 2CH SOUND FIELD A. F. D.
Tip Resuming Playback from the Point Where You Stopped the Disc (Resume Play) When you stop the disc, the receiver remembers the point where you pressed x and “RESUME” appears in the front panel display. As long as you do not remove the disc, Resume Play will work even if the receiver enters standby mode by pressing "/1. H 1 x While playing a disc, press x to stop playback. “RESUME” appears in the front panel display, so you can restart the disc from the point where you stopped the disc.
Using the DVD’s Menu (PBC Playback) With PBC (Playback Control) functions, you can enjoy simple interactive operations, search functions, and other such operations. PBC playback allows you to play VIDEO CDs interactively by following the menu on the TV screen. Playing Discs A DVD is divided into long sections, which make up a picture or music feature. These sections are called “titles.” When you play a DVD which contains several titles, you can select the title you want using TOP MENU/ GUIDE.
To go back to the menu Press O RETURN/EXIT. Notes • Depending on the VIDEO CD, the menu does not appear in Step 1. • Depending on the VIDEO CD, “Press ENTER” in Step 3 may appear as “Press SELECT” in the instructions supplied with the disc. In this case, press H. Tip To play without using PBC, press ./> or NUM and Cursor key while the receiver is stopped to select a track, then press H or ENTER. “Play without PBC” appears on the TV screen and the receiver starts continuous play.
Selecting an album and track 4 Select (TRACK) using X/x and press ENTER. The list of tracks contained in the current album appears. ALBUM– ENTER C/X/x/c ALBUM+ DVD DISPLAY O RETURN/ EXIT 1 2 When the list of all tracks or albums cannot be displayed on the window, the jump bar appears. Press c to select the jump bar icon, and then scroll the jump bar to display the rest of the list using X/x. Press C or O RETURN/EXIT to return to the track or the album list. Press DVD DISPLAY.
Playing JPEG Image Files You can play JPEG image files on CD-ROMs, CD-Rs, or CD-RWs. However, the discs must be recorded according to ISO9660 level 1, level 2 or Joliet format for the receiver to recognize the files. You can also play discs recorded in Multi Session. See the instructions of the CD-R/RW device or recording software (not supplied) for details on the recording format. 1 2 ALBUM– ENTER C/X/x/c ALBUM+ DVD DISPLAY O RETURN/ EXIT Load a data disc recorded in JPEG into the receiver. Press H.
4 Select press ENTER. (FILE) using X/x and The list of files contained in the current album appears. JPEG M 1.HAPPY 2.BIRTHDAY 3.CELEBRATION 4.CHRISTMAS 5.MOM 6.BASEBALL 7.PARTY 8.DAD 9.TRAVEL 10.FRIEND 11.DRIVE 5 Select a file using X/x and press ENTER. The selected file starts playing. To return to the previous display Press O RETURN/EXIT or C. To turn off the Control Menu Press DVD DISPLAY. Note Only alphabetical letters and numbers can be used for album or file names.
To rotate the current image Selecting the Play Mode (All Discs, One Disc, or Album) H You can select the play mode to play all discs continuously, one disc, or one album. C/c PLAY MODE Rotate the current image using C/c Each time you press c, the image turns clockwise by 90°. Each time you press C, the image turns counterclockwise by 90°. Note ENTER C/X/x/c DVD DISPLAY O RETURN/ EXIT You cannot rotate an image during Slide Show. Press H to return to normal play before this operation.
ALL/ONE/ALBUM Creating Your Own Program (Program Play) You can play the contents of a disc in the order you want by arranging the order of the tracks on the disc to create your own Program. You can program up to 25 steps. Playing Discs • ALL: The receiver plays all discs in the receiver consecutively in the order of the disc slot number, and you can set Shuffle Play (except DVD and JPEG) or Repeat Play for all the discs.
2 Press c, then press X/x to select the disc. Program 1 Disc 2 DISC1(CD) 3 DISC2(CD) 4 DISC3(CD) 5 DISC4(CD) 6 DISC5(CD) 7 8 9 10 3 Program 1 Disc 2 DISC1(CD) Track 3 DISC2(CD) ALL TRACKS 4 DISC3(CD) 1 TRACK1 5 DISC4(CD) 2 TRACK2 6 DISC5(CD) 3 TRACK3 7 4 TRACK4 8 5 TRACK5 9 6 TRACK6 10 7 TRACK7 8 TRACK8 9 TRACK9 When the list of all tracks cannot be displayed on the window, the jump bar appears. Press c to select the jump bar icon, and then scroll the jump bar to display the rest of the list using X/x.
Playing in Random Order (Shuffle Play) Setting the shuffle mode in the Control Menu You can select either normal shuffle or album shuffle (MP3 only). Playing Discs You can have the receiver “shuffle” tracks and play them in random order. Subsequent “shuffling” will produce a different playing order. H ENTER X/x DVD DISPLAY PLAY MODE CLEAR H 1 Press DVD DISPLAY. The Control Menu appears.
x When playing a DVD Playing Repeatedly • OFF: does not play repeatedly. • ALL: repeats all the titles (except SHUFFLE (ALL)). • TITLE: repeats the current title on a disc. • CHAPTER: repeats the current chapter. (Repeat Play) You can play all the titles/tracks/files or a single title/chapter/track/album on a disc. In Shuffle or Program Play mode, the receiver repeats tracks in shuffled or programmed order. You cannot perform Repeat Play during PBC playback of VIDEO CDs (page 27).
(Scan, Slow-motion Play) Each time you press m or M during scan, the playback speed changes. Two speeds are available. With each press, the indication changes as follows: Playback direction FF1M t FF2M Playing Discs You can locate a particular point on a disc quickly by monitoring the picture or by playing back slowly. To change the scan speed (DVD/ VIDEO CD only) t Searching for a Particular Point on a Disc t Opposite direction FR1m t FR2m FF2M/FR2m playback speed is faster than FF1M/FR1m.
x When playing a DVD Searching for a Title/ Chapter/Track/Index/ Album/File (TITLE) x When playing a VIDEO CD (TRACK) x When playing a Super Audio CD (TRACK) x When playing a CD You can search a title (DVD), chapter (DVD), track (CD, VIDEO CD, Super Audio CD, MP3), index (VIDEO CD, Super Audio CD), album (MP3, JPEG), and file (JPEG). As titles, tracks, albums and files are assigned individual names on the disc, you can select the desired one from the Control Menu.
Searching for a chapter/index 1 The receiver starts playback from the selected number. Press DVD DISPLAY. The Control Menu appears. To enter the number Press X/x to select the search method. Press NUM and move Cursor key until the number you want to enter appears in the remote’s display. Then push Cursor key. x When playing a DVD (CHAPTER) To turn off the Control Menu x When playing a VIDEO CD Press DVD DISPLAY.
Tip You can change the display to show playing time or remaining time. For details, see “Checking the Playing Time and Remaining Time in the Control Menu” (page 43). Viewing Disc Information Viewing the Playing Time and Remaining Time in the Front Panel Display You can check disc information, such as the remaining time, total number of titles in a DVD, or tracks in a Super Audio CD, CD, VIDEO CD or MP3, using the front panel display (page 90). DISPLAY/ JUMP Press DISPLAY/JUMP.
When playing a DVD Playing time and number of the current title SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX PRO LOGIC ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S SHUFFLE dB PCM DSD NEO:6 kHz DTS-ES 96/24 REPEAT1 FM AM MHz MPEG-2 AAC PROGRAM MEMORY SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX PRO LOGIC ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S dB PCM DSD NEO:6 SHUFFLE kHz DTS-ES 96/24 REPEAT1 FM AM PROGRAM MEMORY MHz MPEG-2 AAC
When playing an MP3 Playing time and current track number SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX PRO LOGIC ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S dB PCM DSD NEO:6 SHUFFLE kHz DTS-ES 96/24 REPEAT1 FM AM PROGRAM MEMORY MHz MPEG-2 AAC Remaining time of the current track SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S PRO LOGIC dB PCM DSD NEO:6 SHUFFLE REPEAT1 FM AM kHz DTS-ES 96/24 P
• C–**:**:** Remaining time of the current chapter • **:**:** Playing time of the menu or current title without a chapter Checking the Playing Time and Remaining Time in the Control Menu x When playing a VIDEO CD (with PBC functions) • **:** Playing time of the current scene x When playing a VIDEO CD (without PBC functions), Super Audio CD or CD Playing Discs You can check the playing time and remaining time of the current title, chapter, or track, and the total playing time or remaining time of the di
Checking the date information (JPEG only) You can check the date information during playback when the Exif* tag is recorded in the JPEG image data. DVD DISPLAY Press DVD DISPLAY during playback. The Control Menu appears. 2:MOUNTAIN FAMILY 1 ( 2 0 ) BIRTHDAY JPEG 01/ 01/ 2003 Date information * “Exchangeable Image File Format” is a digital camera image format defined by the Japan Electronics & Information Technology Industries Association.
The options for AUDIO appear. Sound Adjustments 1:DVD 11 2 ( 2 7 ) MAKING SCENE 18(34) Changing the Sound DVD T 1:32:55 1: ENGLISH 2: FRENCH 3: SPANISH 3 Press X/x to select the desired audio signal. x When playing a DVD Depending on the DVD, the choice of language varies. When 4 digits are displayed, they represent the language code. Refer to the language code list on page 93 to see which language the code represents.
To turn off the Control Menu Press DVD DISPLAY. The display examples are as follows: Notes • PCM (stereo) • For discs not in multiple audio format, you cannot change the sound. • During DVD playback, the sound may change automatically. PROGRAM FORMAT PCM 48kHz 24bit • Dolby Surround Tip PROGRAM FORMAT You can select “AUDIO” directly by pressing AUDIO. Each time you press the button, the item changes.
Enjoying Surround Sound Automatic decoding of the audio input signal (AUTO FORMAT DIRECT AUTO) Display A.F.D. AUTO Using only the front speaker (2 CHANNEL STEREO) This mode outputs the sound from the front left and right speakers. Standard two channel (stereo) sources completely bypass the sound field processing. Multi channel surround formats are downmixed to two channels. This allows you to play any source using only the front left and right speakers.
Selecting a sound field (A.F.D.button) x Neo:6 Music Performs the DTS Neo:6 Music mode decoding. This setting is ideal for standard stereo sources, such as CDs. Advanced setting When a DTS 96/24 signal is input, you can change the sampling frequency. A.F.D. ENTER X/x AMP MENU Press A.F.D. on the remote repeatedly until the sound field you want appears in the front panel display.
Selecting a sound field (MODE button) x C.ST.EX A (Cinema Studio EX A) Reproduces the sound characteristics of the Sony Pictures Entertainment “Cary Grant Theater” cinema production studio. This is a standard mode, great for watching most any type of movie. x C.ST.EX B (Cinema Studio EX B) x C.ST.EX C (Cinema Studio EX C) Reproduces the sound characteristics of the Sony Pictures Entertainment scoring stage.
Cinema Studio EX is the integrated mode which operates these elements simultaneously. Notes • The virtual speaker effect may cause increased noise in the playback signal. • When listening with sound fields that employ virtual speakers, you will not be able to hear any sound coming directly from the surround speakers. • This function is unavailable when playing Super Audio CDs. • When you play a Super Audio CD (Direct Stream Digital), the sound field changes to “AUTO FORMAT DIRECT AUTO” automatically.
Selecting the Surround Back Decoding Mode ENTER X/x AMP MENU 1 Press AMP MENU. Set the function of the remote to DVD, and then press AMP MENU. 2 3 Press X/x repeatedly until “SurrB DEC.” appears in the front panel display, then press ENTER. Press X/x to select the surround back mode you want according to the input stream, then press ENTER or AMP MENU. The default setting is “SB AUTO.” When selecting “SB AUTO” When you input stream contains the 6.
Notes • You can select the surround back decoding only when A.F.D. mode is selected (page 48). In other sound fields, this function is bypassed internally. • Some discs have no Dolby Digital EX flag, even though their packaging may contain a Dolby Digital Surround EX logo. In this case, select “SB MATRIX.
Changing the Speaker Impedance Value You can change the impedance value in accordance with your speaker’s impedance. The default settings are underlined. To enjoy the best possible multi channel surround, connect speakers with a nominal impedance of 8 ohms or higher to the FRONT, CENTER, SURROUND and SURROUND BACK terminals, and set the value to “SP 8Ω.” Refer to the operating instructions supplied with your speakers if you are not sure of their impedance.
3 Press ENTER. The angle number changes to “-.” Using Various Additional Functions 1:DVD 1 2 ( 2 7 ) MAKING SCENE 18(34) Changing the Angles T DVD 1:32:55 –(9) If various angles (multi-angles) for a scene are recorded on a DVD, you can change the viewing angle. For example, while playing a scene of a train in motion, you can display the view from either the front of the train, the left window of the train, or from the right window without having the train’s movement interrupted.
3 Displaying Subtitles Depending on the DVD, the choice of language varies. When 4 digits are displayed, they indicate the language code. Refer to the language code list on page 93 to see which language the code represents. 4 Press ENTER. To cancel the SUBTITLE setting Select “OFF” in Step 3. To turn off the Control Menu Press DVD DISPLAY. Note Depending on the DVD, you may not be able to change the subtitles, even if multilingual subtitles are recorded on it.
• CINEMA 2: Bright colors become brighter and dark colors become richer, and color contrast is increased. Adjusting the Playback Picture 3 (PICTURE MODE) Select the PICTURE MODE you want using X/x, then press ENTER. To turn off the Control Menu Press DVD DISPLAY. You can adjust the video signal of the DVD, VIDEO CD or JPEG from the receiver to obtain the picture quality you want. Choose the setting that best suits the program you are watching.
1 Locking Discs (CUSTOM PARENTAL CONTROL, PARENTAL CONTROL) Insert the disc you want to lock. If the disc is playing, press x to stop playback. 2 In stop mode, press DVD DISPLAY. The Control Menu appears. 3 Custom Parental Control You can set the same Custom Parental Control password for up to 25 discs. If you set a 26th disc, the playback restriction of the disc for which you first set the password is cancelled. Press X/x to select (CUSTOM PARENTAL CONTROL), then press ENTER.
5 Enter your 4-digit password by using NUM and Cursor key, then press ENTER. “Custom parental control is set.” appears and the screen returns to the Control Menu display. Playing the disc for which Custom Parental Control is set 1 If you make a mistake entering your password Insert the disc for which Custom Parental Control is set. The CUSTOM PARENTAL CONTROL display appears. Press C before you press ENTER and input the correct number.
Limiting playback for children (Parental Control) (DVD only) 3 Press X/x to select “PARENTAL CONTROL t,” then press ENTER. x If you have not entered a password The display for registering a new password appears. Playback of some DVDs can be limited according to a predetermined level, such as the age of the viewer. The “Parental Control” function allows you to set a playback limitation level. A scene that is limited is not played, or it is replaced by a different scene.
5 Press X/x to select “STANDARD,” then press ENTER. The selection items for “STANDARD” are displayed. If you make a mistake Press O RETURN/EXIT to go back to the previous screen. To turn off the Setup Display Press DVD SETUP. CUSTOM SETUP PARENTAL CONTROL LEVEL: OFF STANDARD: USA CHANGE PASSWORD OTHERS To turn off the Parental Control function and play the DVD after entering your password Set “LEVEL” to “OFF” in Step 8.
Playing the disc for which Parental Control is set 1 2 Area Code Standard Code number Argentina 2044 Insert the disc and press H. Australia 2047 The PARENTAL CONTROL display appears. Austria 2046 Belgium 2057 Enter your 4-digit password using NUM and Cursor key, then press ENTER. Brazil 2070 Canada 2079 The receiver starts playback. Chile 2090 China 2092 • If you play a DVD which does not have the Parental Control function, playback cannot be limited on this receiver.
Notes Other Operations Using the Remote You can operate the receiver and other units with the remote. A display shows the current unit being operated. With Cursor key, you can easily select a function, disc, or number. About the remote’s display The remote’s display shows the unit being operated. It also lights up when you press Cursor key or buttons when the unit is operated. Display Cursor key Tip You can also operate the TV with the remote in any selection.
Perform operations on another unit with the supplied remote with one button push (Macro Function) Perform operations on another unit with the supplied remote with one button push by using the macro function. You can register two macro functions (M1 or M2), each macro having up to 10 steps. TV ?/1 RM SET UP Press the buttons you want to register for the other unit’s operation(s), and send the code to the supplied remote.
Register the other unit’s remote function (Learn Function) You can register additional functions to the supplied remote button from the other unit's remote. Even though the supplied remote may not have some functions or buttons to operate the VCR or other unit, you can use additional functions with this function. TV ?/1 4 Press the button where you want to register on the supplied remote. The RM SET UP indicator blinks on and off if you press the button which can be registered on the supplied remote.
Controlling Other Units with the Supplied Remote By adjusting the remote signal, you can control your TV, satellite receiver or VCR with the supplied remote. 3 Each time you select the number, push Cursor key. 4 You can set the code number for your TV or satellite receiver separately. Controlling TVs with the remote TV ?/1 RM SET UP AV ?/1 Cursor key* * Use Cursor key only to enter the code number of controllable TVs.
Controlling the TV You can control your TV using the buttons below. By pressing You can TV [/1 Turn the TV on or off. TV/VIDEO Switch the TV’s input source between the TV and other input sources. TV VOL +/– adjust the TV volume. TV CH +/– change the TV channel. Code numbers of controllable satellite receivers If more than one code number is listed, try entering them one at a time until you find the one that works with your satellite receiver.
Controlling the VCR with the remote AV ?/1 RM SET UP Cursor key FUNCTION Manufacturer Code number GENERAL ELECTRIC 721,722,730 GOLDSTAR 723,753 GRUNDIG 724 HITACHI 722,725,729,741 ITT/NOKIA 717 JVC 726,727,728,736 MAGNAVOX 730,731,738 MITSUBISHI/MGA 732,733,734,735 2 3 4 736‘ PANASONIC 729,730,737,738,739,740 PHILIPS 729,730,731 PIONEER 729 RCA/PROSCAN 722,729,730,731,741,747 SAMSUNG 742,743,744,745 SANYO 717,720,746 SHARP 748,749 Press RM SET UP and AV [/1 simultaneously
Notes • Depending on the VCR, you may not be able to control your VCR, or use some of the buttons above. • To operate a DVD player, press FUNCTION and select “DVD” using Cursor key, and then push Cursor key to change the mode of the receiver to DVD. Using Other Units You can use VCRs or other units connected to the VIDEO1, TV/SAT, or VIDEO2 jacks. Refer to the operation manual supplied with the other unit for further information on its operation.
6 Enjoying the Radio A preset number appears in the front panel display. The preset number blinks on and off. Presetting Radio Stations You can preset 20 stations for FM and 10 stations for AM. Before tuning, make sure to turn down the volume to minimum. SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S PRO LOGIC SHUFFLE dB PCM DSD NEO:6 REPEAT1 FM AM kHz DTS-ES 96/24 PROGRAM MEMORY MHz MPEG-2 AAC 7 "/1 8 Press ENTER.
To turn off the radio Listening to the Radio Preset radio stations in the receiver’s memory first (see “Presetting Radio Stations” on page 69). "/1 Cursor key FUNCTION BAND DISPLAY /JUMP PRESET –/+ 1 2 Tips VOLUME +/– To check the frequency Press FUNCTION and select “TUNER” using Cursor key, and then push Cursor key. Press BAND repeatedly until FM or AM appears in the front panel display.
If you make a mistake Naming Preset Stations You can enter a name of up to 8 characters for preset stations. These names (for example, “XYZ”) appear in the receiver’s front panel display when a station is selected. Note that no more than one name can be entered for each preset station. Press C or c repeatedly until the character to be changed flashes, then press X/x to select the desired character. 8 Press ENTER. The station name is stored.
Changing the Brightness of the Front Panel There are four levels of brightness for the front panel display. Adjust the brightness according to your room’s lighting conditions. The default setting is “DIMMER OFF.” ENTER X/x AMP MENU 1 Press AMP MENU. Set the function of the remote to DVD, and then press AMP MENU. 2 3 Press X/x repeatedly until “DIMMER” appears in the front panel display, then press ENTER. Press X/x to change the brightness, then press ENTER or AMP MENU.
2 7 Settings and Adjustments Using the Setup Display Press X/x to select the setup item from the displayed list: “LANGUAGE SETUP,” “SCREEN SETUP,” “CUSTOM SETUP,” “SPEAKER SETUP,” and “RESET*.” Then press ENTER or c. The selected Setup item appears. Example: “SCREEN SETUP” By using the Setup Display, you can make various adjustments to items, such as picture and sound. You can also set the subtitle language and the Setup Display, among other things.
To turn off the Setup Display Press DVD SETUP. * When you select “RESET” in step 2, the following items are returned to the default settings. • Setup Menu (except for the PARENTAL CONTROL) (page 94, 95) After you select “RESET” and press ENTER, select “YES” to reset the settings (it takes a few seconds to complete). Select “NO” and press ENTER to cancel. Do not press POWER on the receiver, when resetting the receiver.
Settings for the Display 4:3 LETTER BOX (SCREEN SETUP) 4:3 PAN SCAN Choose settings according to the TV to be connected. Select “SCREEN SETUP” in the Setup Display. For details on using the display, see “Using the Setup Display” (page 73). The default settings are underlined. Note Depending on the DVD, “4:3 LETTER BOX” may be selected automatically instead of “4:3 PAN SCAN” or vice versa. x SCREEN SAVER x TV TYPE (DVD only) Selects the aspect ratio of the connected TV (4:3 standard or wide).
x COMPONENT OUT This will change the type of signal output from the COMPONENT VIDEO OUT jacks on the receiver. See page 86, 87 for more information about the different types. INTERLACE Select this when you are connected to a standard (interlace format) TV. PROGRESSIVE Select this when you have a TV that can accept progressive signals. Note Custom Settings (CUSTOM SETUP) Allows setting up Parental Control and other settings. Select “CUSTOM SETUP” in the Setup Display.
x AUDIO DRC (AUDIO DYNAMIC RANGE COMPRESSION) Narrows the DYNAMIC range of the sound track. Useful for watching movies at low volume late at night. OFF No compression of DYNAMIC range. STANDARD Reproduces the sound track with the kind of DYNAMIC range that the recording engineer intended. MAX Narrows the DYNAMIC range fully.
SURROUND SURROUND BACK LARGE (BEHIND, LOW), LARGE (BEHIND, HIGH), LARGE (SIDE, LOW), LARGE (SIDE, HIGH), SMALL (BEHIND, LOW), SMALL (BEHIND, HIGH), SMALL (SIDE, LOW), SMALL (SIDE, HIGH): Specify the size, position, and height to implement the Digital Cinema Surround modes in the sound field (page 49) properly. For details, see “Specifying the surround position and height” as below. NONE: Select this if no surround speaker is used. LARGE: Normally select this.
Tip Surround speaker position and height is designed specifically for CINEMA STUDIO EX mode. x DISTANCE The default distance setting for the speakers in relation to the listening position is shown below. 3m (10ft) 3m (10ft) 3m (10ft) 3m (10ft) 3m (10ft) x LEVEL You can vary the level of each speaker as follows. Be sure to set “TEST TONE” to “ON” for easy adjustment. CENTER 0 dB Adjusts the level of the center speaker (–10 dB to +10 dB, 1 dB steps).
Adjusting the speaker balance and level by using the test tone 1 Press DVD SETUP in stop mode. The Setup Display appears. 2 3 4 Press X or x repeatedly to select “SPEAKER SETUP,” then press ENTER. Press X or x repeatedly to select “TEST TONE,” then press ENTER. Press X or x repeatedly to select “ON,” then press ENTER. You will hear the test tone from each speaker in sequence. 5 From your listening position, adjust the value of “BALANCE” and “LEVEL” using C/X/x/c.
Additional Information Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer. Power The power is not turned on. • Check that the AC power cord is connected securely. Picture Sound There is no sound. • The speaker cord is not connected securely. • Check the speaker settings (pages 22, 77).
The sound loses stereo effect when you play a VIDEO CD, a CD, or an MP3. • Set “AUDIO” to “STEREO” in the Control Menu display (page 45). • Make sure the receiver is connected appropriately. The surround effect is difficult to hear when you are playing a Dolby Digital or MPEG audio sound track. • Make sure the sound field function is on (page 47). • Check the speaker connections and settings (pages 15, 77). • Depending on the DVD, the output signal may not be the entire 5.1 channel or 6.1channel.
• The data is not formatted in JPEG even though it has the extension “.JPG” or “JPEG.” • Image length or width is more than 4720 dots. • Remove the disc and select “CUSTOM SETUP” from the setup items. Then select “DATA CD PRIORITY” and set to “JPEG” again. (page 77) • There are more than 8 directory levels. • You cannot play the Progressive JPEG files. The title of a JPEG album or file is not correctly displayed. • The receiver can only display alphabetical letters and numbers.
Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 – 20,000 Hz; rated 120 watts per channel minimum RMS power, with no more than 0.7 % total harmonic distortion from 250 milli watts to rated output. Amplifier section Stereo mode Surround mode 120 W + 120 W (8/4 ohms, 20 – 20,000 Hz, THD 0.7 %) Front: 120 W + 120 W Center*: 120 W Surround*: 120 W + 120 W Surround back*: 120 W (8/4 ohms, 20 – 20,000 Hz, THD 0.
General Power requirements Power consumption Dimensions (approx.) Mass (approx.) Operating temperature Operating humidity Supplied accessories 120 V AC, 60 Hz 180 W 1 W (at the Power Saving Mode) 430 × 136 × 448 mm (17 × 5 3/8 × 17 3/4 inches) (w/h/ d) incl. projecting parts 9.7 kg (21 lb 7 oz) 5°C to 35°C (41°F to 95°F) 5 % to 90 % See page 13. Design and specifications are subject to change without notice.
x Movie mode The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround. The result is enhanced soundfield directionality that approaches the quality of discrete 5.1-channel sound. x Music mode The Music mode is for use with any stereo music recordings, and provides a wide and deep sound space. Dolby Surround Pro Logic As one method of decoding Dolby Surround, Dolby Surround Pro Logic produces four channels from two-channel sound.
channels to enhance the 6.1 channel effect, and is best suited for movies. MUSIC mode allows the front L and R channels to go unprocessed for optimum stereo, with the addition of the surround components adding a special quality to the sound. Parental Control A function of the DVD to limit playback of the disc by the age of the viewer according to the limitation level in each country.
• 2 channel + Multi-channel Super Audio CD This disc consists of a 2 channel playback area and a multi-channel playback area. 2 channel playback area Multi-channel playback area Title The longest section of a picture or music feature on a DVD, movie, etc., in video software, or the entire album in audio software. Track Section of a picture or a music piece on a Super Audio CD, CD, VIDEO CD or MP3. An album is composed of several tracks (MP3 only). VIDEO CD A compact disc that contains moving pictures.
Index to Parts and Controls For more information, refer to the pages indicated in parentheses. Front Panel VOLUME POWER STANDBY 2CH SOUND FIELD A. F. D. MODE TUNER/PRESET DISPLAY DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 FUNCTION EX-CHANGE DISC SKIP PHONES L DISC SKIP (23, 25) B STANDBY indicator (23) M EX-CHANGE (23, 25) C N x (stop) (23) (remote sensor) (13) Additional Information A Power switch (23) D 2CH (47) O X (pause) (24) E A.F.D.
Front Panel Display When playing back a DVD Playing status Lights up when you can change the angle SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX PRO LOGIC ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S SHUFFLE dB PCM DSD NEO:6 REPEAT1 FM AM kHz DTS-ES 96/24 PROGRAM MEMORY MHz MPEG-2 AAC Current play mode Current title Current chapter number number Playing time Current sound When playing back a Super Audio CD, CD, VIDEO CD, or MP3 Current play mode Current disc Light
Rear Panel AUDIO OUT Y PB/CB PR/CR S VIDEO OUT S VIDEO IN S VIDEO IN S VIDEO IN VIDEO OUT VIDEO IN VIDEO IN VIDEO IN COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO 2 VIDEO 1 MONITOR TV/SAT VIDEO 2 VIDEO 1 ANTENNA TV/SAT BACK R SURROUND L R CENTER SPEAKERS L FRONT IMPEDANCE USE 4-16 SUB WOOFER COMPONENT VIDEO IN FM 75 COAXIAL AM DIGITAL COAXIAL IN TV/SAT TV/SAT Y PB/CB PR/CR TV/SAT VIDEO 2 VIDEO 1 OPTICAL IN OPTICAL VIDEO 2 MD/DAT OUT L R AUDIO IN AUDIO IN AUDIO IN M VIDEO1 (AUDIO
Remote F FUNCTION (66, 67, 68, 69, 70) G AUDIO (45) H PLAY MODE (33, 35) I REPEAT (33, 36) J ANGLE (54) K DISPLAY/JUMP (40, 70) L SUBTITLE (55) M .
Language Code List The language spellings conform to the ISO 639: 1988 (E/F) standard.
DVD Setup Menu List You can set the following items with the DVD Setup menu. The default setting are underlined. LANGUAGE SETUP OSD (Selects the language you want to use from the displayed language list.) DVD MENUa) (Selects the language you want to use from the displayed language list.) AUDIOa) (Selects the language you want to use from the displayed language list.) SUBTITLEa) (Selects the language you want to use from the displayed language list.) CUSTOM SETUP PARENTALa) CONTROL LEVEL OFF 8. 7.
SPEAKER SETUP LARGE SMALL LARGE CENTER SMALL NONE SURROUND LARGE (BEHIND, LOW) LARGE (BEHIND, HIGH) LARGE (SIDE, LOW) LARGE (SIDE, HIGH) SMALL (BEHIND, LOW) SMALL (BEHIND, HIGH) SMALL (SIDE, LOW) SMALL (SIDE, HIGH) NONE SURROUND LARGE BACK SMALL NONE SUBWOOFER YES NONE FRONT 0.9m – 6.9m/ DISTANCE 3ft – 23ft (3m/10ft) 0.9m – 6.9m/ CENTER 3ft – 23ft (3m/10ft) SURROUND 0.9m – 6.9m/ 3ft – 23ft (3m/10ft) SURROUND 0.9m – 6.
Index Numerics H R 16:9 75 4:3 LETTER BOX 75 4:3 PAN SCAN 75 Handling discs 9 Radio 70 Rear Panel 91 Region Code 8, 87 Remote 65, 92 REPEAT 36 RESET 74 Resume Play 26 A ALBUM 29, 38 Album 7, 85 ANGLE 54 Antenna Hookups 17 AUDIO 45, 74 AUDIO DRC 77 B BACKGROUND 75 BALANCE 79 Batteries 13 C CHAPTER 39 Chapter 7, 85 COMPONENT OUT 76 Control Menu 11 CUSTOM PARENTAL CONTROL 57 CUSTOM SETUP 76 I INDEX 39 Index 7 J JPEG 30 JPEG DATE 77 L LANGUAGE SETUP 74 Learn Function 64 LEVEL 79 Listening to the Radi
FR
33 AVERTISSEMENT Précautions Sécurité Attention – L’utilisation d’instruments optiques avec ce produit augmente le risque de lésion oculaire. Pour les clients canadiens ATTENTION CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. • Si un objet ou du liquide venait à pénétrer à l’intérieur du boîtier, débranchez l’appareil et faites-le vérifier par un personnel qualifié avant de le remettre en marche.
Félicitations ! Nous vous remercions d’avoir fait l’acquisition de cet ampli-tuner Super Audio CD/DVD de Sony. Avant de le faire fonctionner, lisez attentivement ce mode d’emploi et conservez-le pour toute référence ultérieure. Précautions • Par souci d’économie d’énergie, le système peut être mis complètement hors tension à l’aide de l’interrupteur POWER de l’appareil principal. Bien que le voyant reste allumé pendant quelques temps, le système est complètement hors tension.
Transport de l’ampli-tuner Lorsque vous transportez l’ampli-tuner, appliquez la procédure ci-dessous afin de protéger le mécanisme interne. Retirez tous les disques. « NO DISC » apparaît dans la fenêtre d’affichage du panneau frontal. Maintenez les touches x et DISC 4 de l’ampli-tuner enfoncées pendant 5 secondes environ. Dès que « MECHA LOCK » apparaît dans la fenêtre d’affichage du panneau frontal, mettez l’ampli-tuner hors tension et débranchez son cordon d’alimentation de la prise secteur.
Table des matières Félicitations ! .......................................... 3 Précautions .............................................. 3 A propos de ce mode d’emploi ............... 7 Cet ampli-tuner peut lire les disques suivants ............................................. 7 Terminologie relative aux disques ..........7 Remarques sur les disques .................... 10 Utilisation du menu de commande ....... 11 Recherche d’un point spécifique sur un disque ...........................................
Sélections et réglages Utilisation du menu de configuration................................... 76 Sélection de la langue des menus ou de la bande son ........................................ 77 (CHOIX DE LA LANGUE) Réglages de l’écran ............................... 78 (REGLAGE DE L’ECRAN) Réglages personnalisés ......................... 80 (REGLAGE PERSONNALISE) Réglages des enceintes.......................... 81 (REGLAGE H-P) Informations complémentaires Dépannage.........................................
A propos de ce mode d’emploi • Les instructions contenues dans le présent mode d’emploi décrivent les commandes de la télécommande. Vous pouvez également utiliser les commandes de l’ampli-tuner, si elles portent le même nom ou un nom analogue à celles de la télécommande. • Les symboles suivants sont utilisés dans ce mode d’emploi. Symbole Signification Fonctions disponibles pour les DVD VIDEO et les DVD-R/DVDRW en mode vidéo ou pour les DVD+R/DVD+RW en mode vidéo.
• Scène Sur un CD VIDEO doté de fonctions PBC (page 28), les écrans de menu, les images animées et les images fixes sont divisés en sections appelées « scènes ». • Fichier Il s’agit d’une section d’un CD de données contenant des fichiers image JPEG. Disque Structure du DVD Titre Chapitre Structure du CD VIDEO, Super Audio CD ou CD Structure MP3 Disque Plage • L’ampli-tuner peut lire des CD multi-session lorsqu’une plage audio MP3 est contenue dans la première session.
• • • • • Les sections de données des CD-Extra Les DVD-ROM Les DVD audio Les DVD-RAM Les DVD-RW en mode d’enregistrement vidéo (VR) • Les DVD+RW en mode d’enregistrement vidéo (VR) • Les fichiers JPEG progressifs * Il s’agit d’un format logique de fichiers et de dossiers sur les CD-ROM, défini par l’ISO (Organisation internationale de normalisation). Ne chargez pas les disques suivants : • Les DVD ayant un code local différent (page 8, 90).
Remarques sur les disques Manipulation des disques • Pour que les disques restent propres, tenez-les par la partie périphérique. Ne touchez jamais leur surface. • Ne collez ni papier, ni ruban adhésif sur les disques. • N’exposez pas les disques au rayonnement direct du soleil ou à des sources de chaleur, telles que des conduits de chauffage. Ne les abandonnez pas dans une voiture garée en plein soleil, car la température à l’intérieur de l’habitacle risque d’augmenter considérablement.
Utilisation du menu de commande Utilisez le menu de commande pour sélectionner la fonction souhaitée. Le menu de commande s’affiche lorsque la touche DVD DISPLAY est enfoncée. Pour plus de détails, reportez-vous aux pages indiquées entre parenthèses.
AUDIO (DVD/CD VIDEO/ Super Modifie le réglage audio. Audio CD/CD/MP3 uniquement) (page 46) SOUS-TITRE (DVD uniquement) Affiche les sous-titres. Modifie la langue des sous-titres. ALBUM (JPEG uniquement) Sélectionne l’album (JPEG) à lire. (page 57) (page 30, 39) FICHIER (JPEG uniquement) Sélectionne le fichier (JPEG) à lire. (page 30, 39) DATE (JPEG uniquement) Affiche les informations relatives à la date. ANGLE (DVD uniquement) Modifie l’angle. MODE DE LECTURE Sélectionne le mode de lecture.
Préparation Assurez-vous que vous disposez de l’ensemble des accessoires suivants : • Antenne cadre AM (1) • Fil d’antenne FM (1) • Cordon S vidéo (1) • Télécommande RM-CL700M (1) • Piles R6 (AA) (2) • Mode d’emploi (1) Vous pouvez commander l’ampli-tuner au moyen de la télécommande fournie. Insérez deux piles R6 (AA) en faisant correspondre les pôles 3 et # des piles avec les signes représentés à l’intérieur du compartiment.
Etape 1 : Raccordement des enceintes Vous pouvez profiter du son ambiophonique en raccordant 6 enceintes (enceintes avant gauche/droite, enceinte centrale, enceintes surround gauche/droite et enceinte surround arrière) ainsi qu’un caisson de graves actif à l’ampli-tuner. Si vous ne raccordez pas 6 enceintes et un caisson de graves actif, l’amplituner vous permet néanmoins d’optimiser le signal en fonction du nombre d’enceintes raccordées.
Bornes de raccordement des enceintes A Enceintes avant Bornes SPEAKERS FRONT L et R Enceintes surround Bornes SPEAKERS SURROUND L et R Enceinte surround arrière Borne SPEAKERS SURROUND BACK Enceinte centrale Borne SPEAKERS CENTER Caisson de graves Prise SUBWOOFER AUDIO OUT Préparation Raccordez AUDIO OUT Y PB/CB PR/CR S VIDEO OUT S VIDEO IN S VIDEO IN S VIDEO IN VIDEO OUT VIDEO IN VIDEO IN VIDEO IN COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO 2 VIDEO 1 MONITOR TV/SAT VIDEO 2 VIDEO 1 ANT
Note sur le raccordement des cordons des enceintes à l’amplituner Dénudez l’extrémité des fils sur 10 mm (3/8 pouce) environ, puis torsadez les brins de fils ainsi dénudés. Raccordez les extrémités dénudées des fils aux bornes en veillant à éviter tout contact entre les fils. Assurez-vous que les cordons sont fermement raccordés aux bornes des enceintes et de l’ampli-tuner. 10 mm (3/8 po.) Pour éviter un court-circuit des enceintes Un court-circuit au niveau des enceintes peut endommager l’ampli-tuner.
Etape 2 : Raccordements des antennes Préparation Pour écouter la radio, raccordez les antennes AM/FM fournies.
Si la réception FM est de mauvaise qualité Utilisez un câble coaxial 75 ohms (non fourni) pour raccorder l’ampli-tuner à une antenne FM extérieure comme illustré ci-dessous. Antenne FM extérieure Ampli-tuner ANTENNA FM 75 COAXIAL AM Fil de terre (non fourni) Vers la terre Remarque Si vous raccordez l’ampli-tuner à une antenne extérieure, mettez-la à la terre pour la protéger contre l’orage. Pour éviter une explosion de gaz, ne raccordez pas le fil de terre à un tuyau de gaz.
Cordons requis Cordon S vidéo pour le raccordement d’un téléviseur Préparation Etape 3 : Raccordements du téléviseur et des composants vidéo Cordons audio/vidéo (non fournis) Lorsque vous raccordez un cordon, veillez à faire correspondre les broches à codes de couleur aux prises appropriées des composants.
Téléviseur avec prises COMPONENT VIDEO IN Téléviseur avec prise S VIDEO IN COMPONENT VIDEO IN Y Téléviseur INPUT INPUT S VIDEO IN VIDEO IN PB/CB PR/CR IN IN IN AUDIO OUT PB/CB Y PR/CR S VIDEO OUT S VIDEO IN S VIDEO IN S VIDEO IN VIDEO OUT VIDEO IN VIDEO IN VIDEO IN COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO 2 VIDEO 1 MONITOR TV/SAT VIDEO 2 VIDEO 1 ANTENNA TV/SAT BACK R SURROUND L R CENTER SPEAKERS L FRONT IMPEDANCE USE 4-16 SUB WOOFER COMPONENT VIDEO IN FM 75 COAXIAL Y AM T
Etape 4 : Raccordement du cordon d’alimentation secteur Préparation Avant de raccorder le cordon d’alimentation secteur de cet ampli-tuner à une prise murale (prise secteur), raccordez les enceintes à l’ampli-tuner (voir page 14).
Réglage des enceintes Pour optimiser le son surround, toutes les enceintes, hormis le caisson de graves, doivent être à la même distance de la position d’écoute (A). Cependant, cet appareil vous permet de rapprocher l’enceinte centrale jusqu’à 1,5 mètre a) (B) et les enceintes surround et surround arrière jusqu’à 4,5 mètres b) (C,D) de la position d’écoute. Les enceintes avant peuvent être placées entre 0,9 et 6,9 mètres c) (A) de la position d’écoute.
4 Lecture de disques Lecture de disques Appuyez sur la touche Z de l’amplituner ou sur la touche OPEN/CLOSE de la télécommande et posez un disque dans le plateau de lecture en dirigeant son étiquette vers le haut. Certaines opérations peuvent être différentes ou limitées selon les DVD ou CD VIDEO. Reportez-vous aux instructions d’utilisation fournies avec votre disque.
Pour retirer le disque Appuyez sur la touche Z de l’ampli-tuner ou sur la touche OPEN/CLOSE de la télécommande. « OPEN » apparaît dans la fenêtre d’affichage du panneau frontal. Retirez le disque lorsque le plateau de lecture glisse hors de l’ampli-tuner. – bleu clair : le plateau de lecture est sélectionné ou le disque est en cours de lecture. – éteint : disque absent. – bleu foncé : un disque est présent dans le plateau de lecture, mais celui-ci n’est pas choisi.
Pour Appuyez sur Revenir au chapitre, à la plage, à la scène ou au fichier précédent en mode de lecture continue . Mettre le son en sourdine MUTING. Pour annuler l’effet de sourdine, appuyez de nouveau sur cette touche ou sur VOLUME + pour régler le niveau du volume. Vous pouvez ouvrir le plateau de lecture pendant la lecture d’un disque, afin de vérifier les disques qui vont être lus ou remplacer les disques sans interrompre la lecture du disque en cours.
Remarques Reprise de la lecture à l’endroit où vous avez arrêté le disque (Reprise de la lecture) • Selon le point d’arrêt, il est possible que l’ampli-tuner ne reprenne pas la lecture exactement au même endroit. • Le point d’arrêt de la lecture n’est plus conservé en mémoire si : – vous modifiez le mode de lecture. – vous modifiez le réglage du menu de configuration.
Utilisation du menu du DVD Appuyez sur NUM et déplacez la Touche du curseur jusqu’à ce que le numéro souhaité apparaisse sur l’affichage de la télécommande. Appuyez ensuite sur la Touche du curseur. Lecture de disques Un DVD est divisé en sections longues qui constituent une image ou un morceau de musique. Ces sections sont appelées « titres ». Lorsque vous lisez un DVD contenant plusieurs titres, vous pouvez sélectionner celui de votre choix à l’aide de la touche TOP MENU/GUIDE.
Lecture de CD VIDEO dotés de fonctions PBC (Ver. 2.0) (Lecture PBC) Pour saisir le numéro Appuyez sur NUM et déplacez la Touche du curseur jusqu’à ce que le numéro souhaité apparaisse sur l’affichage de la télécommande. Appuyez ensuite sur la Touche du curseur. Pour revenir au menu Appuyez sur O RETURN/EXIT. Vous pouvez bénéficier d’une certaine interactivité, à savoir utiliser des fonctions de recherche ou d’autres fonctions du même type, grâce aux fonctions PBC (commande de lecture).
Lecture d’une plage audio MP3 1 2 Chargez un disque de données enregistré en MP3 dans l’appareil. Appuyez sur H. ALBUM– ENTER C/X/x/c ALBUM+ DVD DISPLAY O RETURN/ EXIT 1 Appuyez sur DVD DISPLAY. Le menu de commande et le nom du disque de données MP3 apparaissent. 2 L’appareil commence à lire la première plage audio MP3 du premier album du disque. Appuyez sur X/x pour sélectionner (ALBUM), puis appuyez sur ENTER ou sur c. La liste des albums figurant sur le disque apparaît.
Lorsque la liste de toutes les plages ou albums ne peut pas être affichée, la barre de défilement apparaît. Appuyez sur c pour sélectionner l’icône de la barre de défilement, puis déplacez-la pour afficher le reste de la liste à l’aide de X/x. Appuyez sur C ou O RETURN/EXIT pour revenir à la liste des plages ou des albums. 5 Sélectionnez une plage à l’aide de X/x, puis appuyez sur ENTER. La lecture de la plage sélectionnée commence. Pour revenir à l’affichage précédent Appuyez sur O RETURN/EXIT ou C.
ALBUM– ENTER C/X/x/c ALBUM+ DVD DISPLAY O RETURN/ EXIT 5 Sélectionnez un fichier à l’aide de X/x, puis appuyez sur ENTER. La lecture du fichier sélectionné commence. Lecture de disques Lorsque la liste de tous les fichiers ou albums ne peut pas être affichée, la barre de défilement apparaît. Appuyez sur c pour sélectionner l’icône de la barre de défilement, puis déplacez-la pour afficher le reste de la liste à l’aide de X/x.
Diaporama à partir d’un disque de données JPEG Pour faire pivoter l’image en cours M H H C/c 1 2 Appuyez sur M alors qu’une image JPEG est affichée. Faites pivoter l’image en cours à l’aide de C/c Le diaporama démarre à partir de l’image en cours. A chaque pression de c, l’image tourne de 90° dans le sens des aiguilles d’une montre. A chaque pression de C, l’image tourne de 90º dans le sens contraire des aiguilles d’une montre. Appuyez sur H pour quitter le diaporama.
TOUS/UN/ALBUM Sélection du mode de lecture (Tous disques, Un disque ou Album) PLAY MODE Lecture de disques Vous pouvez décider de lire tous les disques en continu, un seul disque ou un seul album. • TOUS : L’ampli-tuner lit successivement tous les disques dans l’ordre des numéros des compartiments pour disque. Vous pouvez aussi écouter ces disques en mode de lecture aléatoire (sauf DVD et JPEG) ou de lecture répétée. • UN : L’ampli-tuner lit seulement le disque que vous avez sélectionné.
Création de votre propre programme 2 Program 1 Disc 2 DISC1(CD) 3 DISC2(CD) 4 DISC3(CD) 5 DISC4(CD) 6 DISC5(CD) 7 8 9 10 (Lecture programmée) Vous pouvez lire le contenu d’un disque dans l’ordre de votre choix en organisant les plages du disque comme bon vous semble pour créer votre propre programme. Vous pouvez programmer jusqu’à 25 plages. PLAY MODE Appuyez sur c, puis sur X/x pour sélectionner le disque. 3 Appuyez sur c. Le curseur se déplace jusqu’à la plage (dans ce cas, « 1 »).
5 Appuyez sur X/x ou sur NUM et la Touche du curseur pour sélectionner « 7 », puis appuyez sur ENTER. 6 Pour programmer d’autres plages, répétez les étapes 2 à 5. Les plages programmées sont affichées dans l’ordre sélectionné. 7 Vous pouvez effectuer une lecture répétée des plages programmées. Appuyez sur REPEAT ou réglez « REPETEE » sur « TOUS » dans la fenêtre du menu de commande en cours de lecture programmée (page 37).
Lecture dans un ordre aléatoire (Lecture aléatoire) Réglage du mode aléatoire dans le menu de commande Vous pouvez sélectionner soit la lecture aléatoire normale, soit la lecture aléatoire de l’album (MP3 uniquement). L’ampli-tuner peut sélectionner des plages et les lire de façon aléatoire. Des lectures aléatoires successives engendrent un ordre de lecture différent. H ENTER X/x DVD DISPLAY PLAY MODE CLEAR H 1 Appuyez sur DVD DISPLAY. Le menu de commande apparaît.
x Lors de la lecture d’un DVD Lecture répétée (Lecture répétée) REPEAT CLEAR • NON : ne lit pas le disque de façon répétée. • TOUS : répète tous les fichiers du disque (si LECTURE CONTINUE est sélectionné en mode de lecture ) ou répète l’album en cours de lecture (si LECTURE CONTINUE (ALBUM) est sélectionné en mode de lecture). ENTER X/x DVD DISPLAY Appuyez sur DVD DISPLAY. x Lorsque la lecture programmée est réglée sur OUI Le menu de commande apparaît.
Conseils • Vous pouvez activer la lecture répétée en mode d’arrêt. Après avoir sélectionné le paramètre « REPETEE », appuyez sur H. L’ampli-tuner démarre la lecture répétée. • Vous pouvez rapidement afficher le statut « REPETEE ». Appuyez sur la touche REPEAT de la télécommande. • Vous pouvez utiliser la lecture répétée pour les titres DVD contenant des chapitres.
Pour changer la vitesse de balayage (DVD/CD VIDEO uniquement) t Sens de lecture AV1M t AV2M t Sens inverse RET1m t RET2m La vitesse de lecture AV2M/RET2m est supérieure à AV1M/RET1m. Visualisation image par image (lecture au ralenti) (DVD/CD VIDEO uniquement) Vous pouvez rechercher un titre (DVD), un chapitre (DVD), une plage (CD, CD VIDEO, Super Audio CD, MP3), un index (CD VIDEO, Super Audio CD) et un album (MP3, JPEG) et un fichier (JPEG).
3 x Lors de la lecture d’un DVD (TITRE) x Lors de la lecture d’un CD VIDEO L’ampli-tuner commence la lecture à partir de la plage sélectionnée. (PLAGE) x Lors de la lecture d’un Super Audio CD (PLAGE) x Lors de la lecture d’un CD Recherche d’un chapitre/ index 1 (PLAGE) Appuyez sur X/x pour sélectionner la plage souhaitée, puis appuyez sur ENTER. Appuyez sur DVD DISPLAY. Le menu de commande apparaît.
4 Appuyez sur X/x pour sélectionner le numéro de chapitre ou d’index que vous souhaitez rechercher, ou saisissez ce numéro. Si vous faites une erreur 5 Appuyez sur ENTER. L’ampli-tuner commence la lecture à partir du numéro sélectionné. x Sélectionnez « 2 » et appuyez sur la Touche du curseur. x Sélectionnez « 1 » et appuyez sur la Touche du curseur. x Sélectionnez « 0 » et appuyez sur la Touche du curseur. x Sélectionnez « 2 » et appuyez sur la Touche du curseur.
Visualisation des informations relatives au disque Lors de la lecture d’un DVD Temps de lecture et numéro du titre en cours SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S PRO LOGIC SHUFFLE dB PCM DSD NEO:6 REPEAT1 FM AM kHz DTS-ES 96/24 MHz MPEG-2 AAC PROGRAM MEMORY Temps restant du titre en cours SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S PRO
Lors de la lecture d’un CD VIDEO (sans fonction PBC), d’un Super Audio CD ou d’un CD Temps de lecture et numéro de la plage en cours (lors de la lecture d’un CD) Temps restant de la plage en cours SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S PRO LOGIC SHUFFLE dB PCM DSD NEO:6 kHz DTS-ES 96/24 REPEAT1 FM AM MHz MPEG-2 AAC PROGRAM MEMORY Temps de lecture du disque SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGI
Remarques • Selon le type de disque en cours de lecture et le mode de lecture, les informations relatives au disque peuvent ne pas s’afficher. • Les étiquettes ID3 s’appliquent uniquement à la version 1. • Si le fichier MP3 que vous lisez comporte une étiquette ID3, ses informations sont affichées à la place du nom de plage. • Les noms d’album ou de plage ne peuvent être constitués que de chiffres et de lettres de l’alphabet. Tout autre caractère est remplacé par « ».
x Lors de la lecture d’un DVD x Lors de la lecture d’un CD VIDEO (doté de fonctions PBC) • **:** Temps de lecture de la scène en cours Vérification des informations relatives à la date (JPEG uniquement) Vous pouvez vérifier les informations relatives à la date lorsque l’étiquette Exif* est enregistrée dans les données d’image JPEG.
Les options de AUDIO apparaissent. Réglages du son 1:DVD 1 2 ( 2 7 ) MAKING SCENE 18(34) Commutation du son Si le DVD est enregistré avec des plages multilingues, vous pouvez sélectionner la langue de votre choix en cours de lecture. Si le DVD est enregistré selon plusieurs formats audio (PCM, Dolby Digital, MPEG audio ou DTS), vous pouvez sélectionner le format audio de votre choix en cours de lecture.
Pour désactiver le menu de commande Exemples d’affichage : • PCM (stéréo) Appuyez sur DVD DISPLAY. PROGRAM FORMAT Remarques PCM 48kHz 24bit • Dolby Surround PROGRAM FORMAT Conseil DOLBY DIGITAL 2/0 Vous pouvez directement sélectionner « AUDIO » en appuyant sur la touche AUDIO. A chaque pression sur cette touche, le paramètre change. DOLBY SURROUND • Dolby Digital 5.
Appuyez plusieurs fois sur la touche A.F.D. de la télécommande jusqu’à ce que l’indication « A.F.D. AUTO » apparaisse dans la fenêtre d’affichage du panneau frontal. Utilisation du son ambiophonique Vous pouvez bénéficier du son ambiophonique en sélectionnant simplement l’un des champs acoustiques préprogrammés, en fonction du programme que vous souhaitez écouter. Ils vous permettent de découvrir chez vous l’acoustique exaltante et puissante des salles de cinéma.
Sélection d’un champ acoustique (touche A.F.D.) x Neo:6 Cinema Exécute le décodage en mode DTS Neo:6 Cinema. x Neo:6 Music Exécute le décodage en mode DTS Neo:6 Music. C’est le réglage idéal pour les sources stéréo standard, notamment les CD. A.F.D. Réglages du son Réglage avancé Vous pouvez modifier la fréquence d’échantillonnage en présence d’un signal d’entrée DTS 96/24. ENTER X/x Appuyez plusieurs fois sur la touche A.F.D.
• En cas de décodage au moyen de DTS 96/24 (à l’exception du mode A.F.D.) dans le champ acoustique, les signaux de sortie sont convertis en 48 kHz (fréquence d’échantillonnage). • Dès qu’une enceinte est réglée sur « PETIT » ou que le caisson de graves est réglé sur « NEANT » au niveau du réglage des enceintes, les signaux de sortie sont convertis en 48 kHz (fréquence d’échantillonnage).
x C.ST.EX A (Cinema Studio EX A) Reproduit les caractéristiques sonores du studio de production cinématographique « Cary Grant Theater » de Sony Pictures Entertainment. Il s’agit d’un mode standard parfaitement adapté à la plupart des types de films. x C.ST.EX B (Cinema Studio EX B) x C.ST.EX C (Cinema Studio EX C) Reproduit les caractéristiques sonores du studio d’arrangement de Sony Pictures Entertainment.
Pour désactiver l’effet surround Appuyez plusieurs fois sur la touche A.F.D. de la télécommande jusqu’à ce que l’indication « A.F.D. AUTO » apparaisse dans la fenêtre d’affichage du panneau frontal, ou appuyez sur la touche 2CH de la télécommande pour afficher « 2CH STEREO ». Remarques • Cette fonction n’est pas disponible lors de la lecture des Super Audio CD.
En cas de sélection de « SB AUTO » En cas de sélection de « SB OFF » Lorsque le flux d’entrée contient l’indicateur de décodage 6.1 canauxa), le décodeur approprié est appliqué afin de décoder le signal surround arrière. Aucun décodage surround arrière n’est effectué. Canal de sortie Décodeur surround arrière appliqué Dolby Digital 5.1 5.1 — DTS 5.1 5.1 — Dolby Digital EXb) 6.1 Le décodeur Matrix est conforme à la norme Dolby Digital EX. DTS-ES Matrix 6.1 6.1c) DTS-ES Discrete 6.1d) 6.
Sélection du décodage prioritaire Cette fonction vous permet de sélectionner un décodage prioritaire lorsque des signaux numériques sont présents au niveau de la prise d’entrée DIGITAL IN (OPTICAL IN/ COAXIAL IN), ou sont traités en mode DVD. ENTER X/x AMP MENU 1 Appuyez sur AMP MENU. Réglez la fonction de la télécommande sur DVD, puis appuyez sur AMP MENU. 2 3 Appuyez plusieurs fois sur X/x jusqu’à ce que « DEC. PRI.
Modification de la valeur d’impédance des enceintes ENTER X/x Pour profiter du meilleur son surround multicanaux possible, raccordez des enceintes d’une impédance nominale égale ou supérieure à 8 ohms aux bornes FRONT, CENTER, SURROUND et SURROUND BACK, et réglez la valeur sur « SP 8Ω ». Reportez-vous au mode d’emploi joint aux enceintes si vous n’êtes pas sûr de leur impédance. (Ces renseignements figurent souvent à l’arrière des enceintes.
1:DVD 1 2 ( 2 7 ) MAKING SCENE 18(34) Utilisation de diverses fonctions complémentaires T DVD 1:32:55 1(9) Commutation des angles 3 Si plusieurs angles d’une scène sont enregistrés sur un DVD, vous pouvez modifier l’angle d’observation. Par exemple, dans une scène de train en marche, vous pouvez afficher la vue observée depuis l’avant du train, de la fenêtre gauche du train ou de la fenêtre droite, sans que le mouvement du train soit interrompu. L’indication du numéro d’angle est remplacée par « - ».
3 Affichage des sous-titres Les langues que vous pouvez sélectionner diffèrent suivant les DVD. Si 4 chiffres sont affichés, ils représentent le code de langue. Reportez-vous à la liste des codes de langue page 99 pour voir quelle langue le code représente. 4 Appuyez sur ENTER. Pour annuler le réglage SOUSTITRE Sélectionnez « NON » à l’étape 3. Pour désactiver le menu de commande Appuyez sur DVD DISPLAY.
• DYNAMIQUE 2 : Restitue une image plus dynamique que DYNAMIQUE 1 en augmentant davantage encore le contraste et la densité de couleur de l’image. • CINEMA 1 : Accentue les détails des zones sombres en augmentant le niveau de noir. • CINEMA 2 : Accentue la luminosité des couleurs vives et la richesse des couleurs foncées, ainsi que le contraste des couleurs.
Verrouillage de disques (VERROUILLAGE PARENTAL PERSONNALISE, CONTROLE PARENTAL) Pour saisir un mot de passe à 4 chiffres à l’aide de la touche NUM et de la Touche du curseur Appuyez sur NUM et sélectionnez le nombre à l’aide de la Touche du curseur, puis appuyez sur celle-ci. 1 Si le disque est en cours de lecture, appuyez sur x pour l’arrêter. 2 En mode d’arrêt, appuyez sur DVD DISPLAY. Le menu de commande apparaît.
x Si vous avez déjà enregistré un mot de passe 3 Saisissez un nouveau mot de passe à 4 chiffres à l’aide de la touche NUM et de la Touche du curseur, puis appuyez sur ENTER. 4 Pour confirmer votre mot de passe, saisissez-le de nouveau à l’aide de la touche NUM et de la Touche du curseur, puis appuyez sur ENTER. L’écran de saisie du mot de passe apparaît. Verrouillage parental personnalisé Tapez le mot de passe, puis appuyez sur ENTER .
Lecture limitée pour les enfants (contrôle parental) (DVD uniquement) 3 Appuyez sur X/x pour sélectionner « CONTROLE PARENTAL t », puis appuyez sur ENTER. x Si vous n’avez pas saisi de mot de passe L’écran de saisie d’un nouveau mot de passe apparaît. Touche du curseur NUM REGLAGE PERSONNALISE CONTROLE PARENTAL Introduisez un nouveau mot de passe à 4 chiffres, puis appuyez sur ENTER .
4 Saisissez votre mot de passe à l’aide de la touche NUM et de la Touche du curseur, puis appuyez sur ENTER. 8 Le réglage du contrôle parental est terminé. L’écran de réglage du niveau de limitation de la lecture et de modification du mot de passe apparaît. REGLAGE PERSONNALISE CONTROLE PARENTAL NIVEAU: STANDARD: CHANGER MOT DE PASSE Sélectionnez le niveau souhaité à l’aide de X/x, puis appuyez sur ENTER.
Lecture d’un disque en mode de contrôle parental 1 2 Code de zone Norme Numéro de code Allemagne 2109 Insérez le disque et appuyez sur H. Argentine 2044 L’écran CONTROLE PARENTAL apparaît. Australie 2047 Autriche 2046 Saisissez votre mot de passe à 4 chiffres à l’aide de la touche NUM et de la Touche du curseur, puis appuyez sur ENTER.
DVD t VIDEO1 t VIDEO2 t TV/SAT t MD/DAT t TUNER t M1 t M2 Fonctions complémentaires Remarques Utilisation de la télécommande Vous pouvez commander l’ampli-tuner et d’autres appareils au moyen de la télécommande. L’appareil que vous commandez apparaît sur l’affichage de la télécommande. A l’aide de la Touche du curseur, vous pouvez facilement sélectionner une fonction, un disque ou un numéro.
Commande d’un autre appareil à l’aide de la télécommande fournie en n’appuyant que sur une seule touche (fonction macro) Commandez un autre appareil à l’aide de la télécommande fournie en n’appuyant que sur une seule touche grâce à la fonction macro. Vous pouvez enregistrer deux fonctions macro (M1 ou M2), comportant chacune 10 pas.
Enregistrement de fonctions de la télécommande de l’autre appareil (Fonction d’apprentissage) Vous pouvez enregistrer d’autres fonctions de la télécommande de l’autre appareil dans la télécommande fournie. Même si la télécommande fournie ne possède pas certaines fonctions ou touches de commande du magnétoscope ou d’un autre appareil, vous pouvez utiliser des fonctions supplémentaires grâce à la fonction d’apprentissage.
Si vous souhaitez effacer la fonction que vous avez enregistrée Avant l’étape 5, maintenez la touche TV/1 enfoncée pendant plus de 2 secondes avant d’envoyer le code. « CLEAR » apparaît sur l’affichage de la télécommande et la fonction enregistrée est effacée. Remarques Conseil Vous pouvez enregistrer une fonction dans chaque numéro de la télécommande. Appuyez sur NUM et sélectionnez un numéro plutôt que d’appuyer sur la touche à l’étape 5.
2 3 Appuyez sur TV [/1. Fabricant Numéro de code Le témoin RM SET UP s’allume et « TV KEY » apparaît sur l’affichage de la télécommande. SHARP 535 TELEFUNKEN 523,536,537,538 THOMSON 530,537,539 A l’aide de la Touche du curseur, saisissez le code du fabricant de votre téléviseur (en vous reportant au tableau). TOSHIBA 535,540,541 ZENITH 542,543 Chaque fois que vous sélectionnez un numéro, appuyez sur la Touche du curseur.
1 Appuyez simultanément sur RM SET UP et AV [/1. Le témoin RM SET UP s’allume et « IR SET » apparaît sur l’affichage de la télécommande. 2 3 A l’aide de la Touche du curseur, saisissez le code du fabricant de votre récepteur satellite (en vous reportant au tableau). Appuyez sur la Touche du curseur après avoir sélectionné le code à 3 chiffres. Une fois l’enregistrement terminé, le témoin RM SET UP clignote deux fois.
Commande du magnétoscope avec la télécommande RM SET UP AV ?/1 Touche du curseur FUNCTION Fabricant Numéro de code SONY 701,702,703,704,705,706 AIWA 710,750,757,758 AKAI 707,708,709,759 BLAUPUNKT 740 EMERSON 711,712,713,714,715,716,750 FISHER 717,718,719,720 GENERAL ELECTRIC 721,722,730 GOLDSTAR 723,753 GRUNDIG 724 HITACHI 722,725,729,741 ITT/NOKIA 717 JVC 726,727,728,736 MAGNAVOX 730,731,738 MITSUBISHI/MGA 732,733,734,735 1 Appuyez simultanément sur RM SET UP et AV [/1.
Vous pouvez AV [/1 Mettre le magnétoscope sous tension ou hors tension. NUM et la Touche du curseur Sélectionner un canal. ENTER Confirmer le canal sélectionné. AUDIO Modifier le son. CH –/+ Changer les canaux du magnétoscope. m/M Avancer rapidement ou revenir en arrière rapidement. H Lire. X Passer en mode pause. x Arrêter. AV MENU Afficher le menu. DVD DISPLAY Activer ou désactiver l’affichage. C/X/x/c/ ENTER Sélectionner l’élément du menu ou du guide des programmes.
Utilisation de la radio 4 5 Présélection des stations de radio Vous pouvez présélectionner 20 stations FM et 10 stations AM. Avant de procéder à la syntonisation, veillez à réduire le volume au minimum. 6 PRESET –/+ Touche du curseur BAND TUNING –/+ Appuyez plusieurs fois sur X ou x jusqu’à ce que l’indication « MEMORY » apparaisse dans la fenêtre d’affichage du panneau frontal. Appuyez sur ENTER. Un numéro de présélection apparaît dans la fenêtre d’affichage du panneau frontal.
Pour modifier l’intervalle de syntonisation AM Ecoute de la radio Commencez par présélectionner des stations de radio dans la mémoire de l’ampli-tuner (voir « Présélection des stations de radio » à la page 72). FUNCTION DISPLAY /JUMP PRESET –/+ 2 3 Appuyez plusieurs fois sur PRESET + ou – pour sélectionner la station présélectionnée de votre choix. A chaque pression sur la touche, l’amplituner syntonise une station présélectionnée.
Pour vérifier la fréquence Appuyez plusieurs fois sur DISPLAY/JUMP. A chaque pression sur DISPLAY/JUMP, la fenêtre d’affichage du panneau frontal change de la façon suivante : nom d’index de la station* t fréquence t nom d’index de la station... * S’affiche si vous avez saisi un nom pour une station présélectionnée. Reportez-vous à la section « Affectation d’un nom aux stations présélectionnées » (page 74).
Modification de la luminosité du panneau frontal Il existe quatre niveaux de réglage de la luminosité de la fenêtre d’affichage du panneau frontal. Réglez la luminosité en fonction des conditions d’éclairage ambiantes. Le réglage par défaut est « DIMMER OFF ». x DIMMER 2 La fenêtre d’affichage du panneau frontal, le témoin MULTI CHANNEL DECODING et les témoins DISC sont faiblement allumés. x DISP OFF Eteint la fenêtre d’affichage du panneau frontal, le témoin MULTI CHANNEL DECODING et les témoins DISC.
1 Sélections et réglages En mode d’arrêt, appuyez sur DVD SETUP. Le menu de configuration apparaît. Utilisation du menu de configuration L’utilisation du menu de configuration vous permet d’effectuer divers réglages de paramètres comme l’image et le son. Vous pouvez également, définir la langue des soustitres et du menu de configuration, notamment. Pour obtenir plus de détails sur chaque paramètre du menu de configuration, reportezvous à la page 77-84.
4 Sélectionnez un paramètre à l’aide de X/x, puis appuyez sur ENTER. Le paramètre est sélectionné et la configuration est terminée. Exemple : « 4:3 PAN SCAN » Sélection de la langue des menus ou de la bande son (CHOIX DE LA LANGUE) Réglage sélectionné REGLAGE DE L'ECRAN TYPE TV: 4:3 PAN SCAN ECONOMISEUR D'ECRAN: OUI ARRIERE-PLAN POCHETTE SORTIE COMPOSANT: INTERLACE Appuyez sur DVD SETUP.
Conseil Si vous sélectionnez « AUTRES t » dans « MENU DVD », « SOUS-TITRE » ou « AUDIO », sélectionnez et saisissez le code de langue à partir de la liste en utilisant la touche NUM et la Touche du curseur, puis appuyez sur ENTER (page 99). Après avoir effectué une sélection, le code de langue (4 chiffres) s’affiche de nouveau lorsque vous sélectionnez « AUTRES t ». Réglages de l’écran (REGLAGE DE L’ECRAN) Choisissez les réglages en fonction du téléviseur à raccorder.
4:3 LETTER BOX 4:3 PAN SCAN BLEU L’arrière-plan est de couleur bleue. NOIR L’arrière-plan est de couleur noire. x SORTIE COMPOSANTE Permet de modifier le type du signal émis par les prises COMPONENT VIDEO OUT de l’amplituner. Reportez-vous à la page 91, 92 pour obtenir plus d’informations sur les différents types. 16:9 INTERLACE Remarque PROGRESSIVE Sélectionnez ce paramètre lorsque vous disposez d’un téléviseur qui peut accepter les signaux progressifs.
Réglages personnalisés (REGLAGE PERSONNALISE) Permet de régler le contrôle parental et d’autres paramètres. Sélectionnez « REGLAGE PERSONNALISE » dans le menu de configuration. Pour obtenir plus de détails sur l’utilisation du menu de configuration, reportez-vous à la section « Utilisation du menu de configuration » (page 76). Les réglages par défaut sont soulignés.
Remarques • Lors de la lecture des CD multi-session, l’ampli-tuner détermine la cible à lire comme dernière session ou comme session liée à celle-ci. • Si vous modifiez ce paramètre, réinsérez le disque. x DATE JPEG Modifiez l’ordre des informations relatives à la date d’une image JPEG dans le menu de commande.
CENTRE SURROUND SURROUND ARRIERE GRAND : Sélectionnez ce paramètre par défaut. PETIT : Sélectionnez ce paramètre si vous utilisez une enceinte centrale de petite taille. NEANT : Sélectionnez ce paramètre si vous n’utilisez aucune enceinte centrale.
Veillez à modifier la valeur dans le menu de configuration lorsque vous déplacez les enceintes. Schéma des positions AVANT La distance des enceintes avant par 3 m/10 pieds rapport à la position d’écoute peut être définie par incréments de 0,3 mètre (1 pied), entre 0,9 et 6,9 mètres (3 et 23 pieds).
SURROUND ARRIERE 0 dB Règle le niveau des enceintes arrière surround (–10 dB à +10 dB, pas de 1dB). INFRAGRAVE 0 dB Règle le niveau du caisson de graves (–10 dB à +10 dB, pas de 1 dB). x ÉQUILIBRE Vous pouvez faire varier la balance des enceintes gauche et droite de la façon suivante. Veillez à régler « TEST TONALITE » sur « OUI » pour faciliter le réglage. Réglage de la balance et du niveau des enceintes à l’aide du test de tonalité 1 Le menu de configuration apparaît.
Informations complémentaires Dépannage Si vous rencontrez l’une des difficultés suivantes lors de l’utilisation de cet ampli-tuner, consultez ce guide de dépannage pour tenter de remédier au problème. Si le problème persiste, consultez votre revendeur Sony le plus proche. Alimentation L’ampli-tuner ne se met pas sous tension. • Vérifiez que le cordon d’alimentation secteur est correctement raccordé. Image L’image comporte des parasites. • Le disque est sale ou défectueux.
• Les fiches et les prises sont sales. Essuyez-les avec un chiffon légèrement imbibé d’alcool. • Sélectionnez « DEC. PRI. » sous AMP MENU et choisissez « AUTO » lors de la lecture de signaux DTS-CD à partir d’un appareil externe raccordé à la prise DIGITAL IN (OPTICAL IN/COAXIAL IN) (page 54). • Nettoyez le disque. Lorsque la lecture du CD (signal PCM) démarre, aucun son ne se produit au départ. • Sélectionnez « DEC. PRI. » dans le AMP MENU puis choisissez « PCM » (page 54).
Impossible de lire la plage audio MP3. • Le CD de données n’est pas enregistré au format MP3 conformément aux normes ISO9660 Niveau 1/ Niveau 2 ou Joliet. • La plage audio MP3 ne possède pas l’extension « .MP3 ». • Les données ne sont pas formatées au format MP3 bien qu’elles en aient l’extension (« .MP3 »). • L’ampli-tuner peut uniquement lire des fichiers audio MP3 (MPEG1 Audio Layer3). • Retirez le disque et sélectionnez « REGLAGE PERSONNALISE » parmi les paramètres de configuration.
Impossible de changer la langue des soustitres. • Il n’y a pas de sous-titres multilingues enregistrés sur le DVD en cours de lecture. • Le DVD ne permet pas de changer les sous-titres. Les sous-titres ne peuvent pas être désactivés. • Le DVD ne permet pas de désactiver les soustitres. Impossible de commuter les angles. • Plusieurs angles ne sont pas enregistrés sur le DVD qui est en cours de lecture (page 56). • Le DVD ne permet pas de changer les angles.
Lecteur Super Audio CD/DVD Laser A semi-conducteur (Super Audio CD/DVD : λ = 650 nm) (CD : λ = 780 nm) Durée d’émission : continue Système de format des signaux NTSC Partie tuner FM Système Gamme de syntonisation Antenne Bornes d’antenne Fréquence intermédiaire Système de synthétiseur numérique à boucle à verrouillage de phase à quartz 87,5 – 108,0 MHz (pas de 100 kHz) Fil d’antenne FM 75 ohms, dissymétrique 10,7 MHz Système Gamme de syntonisation Antenne Fréquence intermédiaire Système de synthétiseu
Glossaire Album Il s’agit d’une section d’un morceau musical ou d’une image sur un CD de données contenant des plages audio MP3 ou des fichiers JPEG. CD VIDEO Disque compact contenant des images animées. Les données vidéo utilisent le format MPEG 1, une norme internationale appliquée pour la technologie de compression numérique. Les données vidéo sont compressées environ 140 fois en moyenne. Par conséquent, un CD VIDEO de 12 cm peut contenir jusqu’à 74 minutes d’images animées.
Dolby Pro Logic II La technologie Dolby Pro Logic II crée cinq canaux de sortie à large bande passante à partir de sources limitées à deux canaux. Ceci est réalisé à l’aide d’un décodeur ambiophonique à matrice haute-fidélité qui extrait les propriétés spatiales de l’enregistrement original sans l’ajout de colorations sonores. x Mode film (Movie mode) Le mode film est utilisé par les programmes de télévision stéréo et toutes les émissions codées en Dolby Surround.
Format progressif (balayage séquentiel) Par rapport au format entrelacé, le format progressif peut reproduire 60 images par seconde et donc toute les lignes de balayage (525 lignes pour le système NTSC). La qualité globale de l’image s’en trouve améliorée et les images fixes, le texte et les lignes horizontales sont plus nets. Ce format est compatible avec le format progressif 525.
• Super Audio CD 2 canaux + multi-canaux Ce disque est constitué d’une zone de lecture à 2 canaux et d’une zone de lecture multicanaux. Zone de lecture à 2 canaux Zone de lecture multicanaux Titre Il s’agit de la section la plus longue d’une image ou d’un morceau musical sur un DVD, d’un film, etc., pour un logiciel vidéo ou de l’album entier pour un logiciel audio.
Index des composants et des commandes Pour plus de détails, reportez-vous aux pages indiquées entre parenthèses. Panneau frontal VOLUME POWER STANDBY 2CH SOUND FIELD A. F. D. MODE TUNER/PRESET DISPLAY DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 FUNCTION EX-CHANGE DISC SKIP PHONES A Interrupteur Marche/Arrêt (23) N x (Arrêt) (23) C O X (Pause) (24) (Capteur de télécommande) (13) D 2CH (2 canaux) (48) P N (Lecture) (23) E A.F.D.
Fenêtre d’affichage du panneau frontal Pendant la lecture d’un DVD Statut de lecture S’allume lorsque vous changez d’angle SACD HYBRID DVD ANGLE CD MP3 VIDEO CD PBC NTSC PROGRESSIVE DIGITAL EX PRO LOGIC ALL 1DISCS TITLE TRACK CHAPTER INDEX H TUNED M MONO ST S SHUFFLE dB PCM DSD NEO:6 REPEAT1 FM AM kHz DTS-ES 96/24 PROGRAM MEMORY MHz MPEG-2 AAC Mode de lecture en cours Numéro du titre Numéro du chapitre en cours en cours Temps de lecture Son en cours Lors de la lecture d’un Super Audio CD, CD, CD VIDEO
Panneau arrière AUDIO OUT Y PB/CB PR/CR S VIDEO OUT S VIDEO IN S VIDEO IN S VIDEO IN VIDEO OUT VIDEO IN VIDEO IN VIDEO IN COMPONENT VIDEO OUT MONITOR TV/SAT VIDEO 2 VIDEO 1 MONITOR TV/SAT VIDEO 2 VIDEO 1 ANTENNA TV/SAT BACK R SURROUND L R CENTER SPEAKERS L FRONT IMPEDANCE USE 4-16 SUB WOOFER COMPONENT VIDEO IN FM 75 COAXIAL AM DIGITAL COAXIAL IN TV/SAT TV/SAT Y PB/CB PR/CR TV/SAT VIDEO 2 VIDEO 1 OPTICAL IN OPTICAL VIDEO 2 MD/DAT OUT L R AUDIO IN AUDIO IN AUDIO IN A Prises CO
Télécommande D Touche du curseur (23, 24, 27, 34, 39, 56, 59, 61, 65, 66, 67, 68, 70, 71, 72, 73, 76) E DISC (Disque) (23, 24) F FUNCTION (Fonction) (68, 70, 71, 72, 73) G AUDIO (46) H PLAY MODE (Mode de lecture) (34, 36) I REPEAT (Répétition) (34, 37) J ANGLE (56) K DISPLAY/JUMP (Affichage/Saut) (42, 73) L SUBTITLE (Sous-titres) (57) M .
ef AV MENU/ALBUM+ (Menu AV/Album+) (27, 29, 30, 68) eg VOLUME +/– (24, 73) eh O RETURN/EXIT (Retour/Quitter) (28, 29, 30, 34, 39, 61, 76) ej TV/VIDEO (67) ek MUTING (Sourdine) (24) el AMP MENU (Menu amplification) (49, 52, 54, 55, 72, 74, 75) r; DVD SETUP (Configuration DVD) (61, 76) 98FR
Liste des codes de langue L’orthographe des langues est conforme à la norme ISO 639 : 1988 (E/F).
Liste des paramètres du menu de configuration DVD Vous pouvez régler les paramètres suivants avec le menu de configuration DVD. Le réglage par défaut est souligné. CHOIX DE LA LANGUE ECRANS REGLAGE DE L’ECRAN (Sélectionnez la langue de votre choix à partir de la liste des langues affichées.) MENU DVDa) (Sélectionnez la langue de votre choix à partir de la liste des langues affichées.) AUDIOa) SOUSTITREa) (Sélectionnez la langue de votre choix à partir de la liste des langues affichées.
REGLAGE H-P TAILLE CENTRE SURROUND GAUCHE SURROUND DROIT SURROUND ARRIERE INFRAGRAVE ÉQUILIBRE TEST TONALITE AVANT NON OUI –10 dB – +10 dB (0 dB) –10 dB – +10 dB (0 dB) –10 dB – +10 dB (0 dB) –10 dB – +10 dB (0 dB) –10 dB – +10 dB (0 dB) 6 pas à gauche ou à droite (CENTRE) Informations complémentaires GRAND PETIT GRAND CENTRE PETIT NEANT SURROUND GRAND (DERRIERE, BAS) GRAND (DERRIERE, HAUT) GRAND (LATERAL, BAS) GRAND (LATERAL, HAUT) PETIT (DERRIERE, BAS) PETIT (DERRIERE, HAUT) PETIT (LATERAL, BAS) PET
Index Chiffres E P 16:9 78 4:3 LETTER BOX 78 4:3 PAN SCAN 78 Economie d’énergie 24 ECONOMISEUR D’ECRAN 79 Ecoute de la radio 73 Ecran de menu Affichage du menu de commande 11 ECRANS 77 ÉQUILIBRE 84 Panneau arrière 96 Panneau frontal 94 Piles 13 PLAGE 39 Plage 7, 92 PLAY MODE 34, 36 PRIORITE CD DONNEES 80 A ALBUM 29, 39 Album 7, 90 ALEATOIRE 36 ANGLE 56 ARRIERE-PLAN 79 AUDIO 46, 77 Avance rapide 38 B Balayage 38 C CD VIDEO 90 Champ acoustique 48 CHAPITRE 40 Chapitre 7, 90 CHOIX DE LA LANGUE 77 Code l
Sony Corporation Printed in Malaysia