CWPL Series CWPL series Hardware Specification Rev. 0.
CWPL Series Document Revision 0.1 Date Apr. 19, 2010 Modifier Yishin Wu 0.2 Aug. 13, 2010 Yishin Wu 0.3 Aug.
CWPL Series Contents 1. INTRODUCTION ...................................................................................... 6 1.1 Product Overview ......................................................................................... 6 1.2 Key Features ................................................................................................. 6 3. ELECTRICAL SPECIFICATIONS ............................................................ 7 3.1 Pin Definitions ..........................................
CWPL Series 7. PART NUMBERING ............................................................................... 14 7.1 Part Numbering........................................................................................... 14 7.2 ID Definitions .............................................................................................. 15 8. REGULATORY .......................................................................................
CWPL Series Figures Figure 2.2 CWPL010 Series block diagram .................................................... 7 Figure 4.1 Two Connector- CWPL010 series perspective ............................. 11 Figure 5.1 Two Connector- CWPL010 series mechanical drawing .............. 12 Figure 5.2 RF connector Dimensions ............................................................. 13 Figure 5.3 CWPL0102U Label drawing ........................................................... 13 Figure 7.1 Part Numbering ........
CWPL Series 1. Introduction 1.1 Product Overview The Sony CWPL010 series wireless LAN module contains the Ralink® RT3370 single chip which is a highly integrated MAC/BBP for 2.4GHz RF transmission and supporting 150Mbps PHY rate. It fully complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards, delivers reliable, cost-effective, throughput from an extended distance.
CWPL Series 2. System Architecture Figure 2.1 CWPL010 Series block diagram 3. Electrical Specifications 3.1 Pin Definitions Table 3.1 Pin Definitions Signal Group Signal Name Pin No. Direction Description D+ UDP 2 Input/Output differential pair for transmit D- UDM 3 Input/Output differential pair for receive +5.0V UV+ 4 Input +5.0V V source GND GND 1 N/A Return current path WSP WSP WSP 6 Input/Output GND GND GND 5 N/A USB Interface Power +5.
CWPL Series 3.2 DC Specifications The Max Power (as max defined in USB Spec) is 2500mW 500mA For all USB voltage rails (5.0V), it is recommended not to exceed 100mVpp noise in the frequency range of 10-500KHz. Table 3.2 DC Specifications Parameters Symbol 5V Supply Voltage +UV Conditions Min. - 4.75 Typ. Max. 5.0 5.25 Unit V 3.2.1 Power Consumption Specifications Power consumption is measured using current probe loop on the Power rails of the USB interface (Pins).
CWPL Series 4. RF Specification 4.1 TX Specifications Table 4.1 TX Specifications ModData Rate (Mbps) Modulation Tx Target Power (dBm) 1 DBPSK 15 2 DQPSK 5.5 Data Rate (Mbps) Modulation Tx Target Power (dBm) HT20-7.22 BPSK 15 15 HT20-14.44 QPSK 15 CCK 15 HT20-21.67 QPSK 15 11 CCK 15 HT20-28.89 16-QAM 15 6 OFDM 15 HT20-43.33 16-QAM 15 9 OFDM 15 HT20-57.78 64-QAM 15 12 OFDM 15 HT20-65 64-QAM 14 18 OFDM 15 HT20-72.
CWPL Series 4.2 RX Specifications Table 4.2 RX Specifications Data Rate (Mbps) Modulation Rx Sensitivity (dBm) 1 DBPSK -92 2 DQPSK 5.5 Data Rate (Mbps) Modulation Rx Sensitivity (dBm) HT20-7.22 BPSK -87 -91 HT20-14.44 QPSK -83 CCK -91 HT20-21.67 QPSK -82 11 CCK -88 HT20-28.89 16-QAM -79 6 OFDM -88 HT20-43.33 16-QAM -76 9 OFDM -87 HT20-57.78 64-QAM -72 12 OFDM -85 HT20-65 64-QAM -70 18 OFDM -83 HT20-72.
CWPL Series 4.3 Antenna Specifications Nominal antenna port impedance specification is 50 ohms for the Sony CWPL010 series hardware. For regulatory requirements, it is assumed that the antenna gain is: Antenna gain for the 2.4GHz band : 1.6dBi There are two antennas supporting 2.4-2.5GHz band. The Sony HD96017 connector will be used on the Sony CWPL010 series hardware. The antenna will be defined Main and Aux where is listing below: Figure 4.
CWPL Series 5. Mechanical Specifications 5.1 Mechanical Drawing Figure 5.
CWPL Series 5.2 RF connector Manufacturer: Sony Manufacturer P/N: HD96017 5.2.1 Specification Operating temperature range: -40℃ ℃~90℃ ℃ Storage temperature range: -40℃ ℃~90℃ ℃ Characteristic impedance: 50Ω (0~3GHz) Voltage standing wave ratio: VSWR<=1.3 (0.045~3GHz) 5.2.2 Dimensions: (Unit: mm) Figure 5.2 RF connector dimensions 5.3 Label Specifications Figure 5.
CWPL Series 6. Environmental Specifications The following tables provide normal operating conditions and maximum rating requirements for CWPL010 series hardware. Table 6.1 Operating Conditions Environment Limits Operating 0-70℃ ※The radio parts at operating state and above temperature of T-shield. Table 6.2 Non-operating Conditions Temperature Environment Humidity Min. Typ. Max. Unit Min. Typ. Max.
CWPL Series 7.2 ID Definitions Table 7.1 ID Definitions WLAN Type Mode PID VID CPWL101UXXX-RT3370 BGN 0x0006 0x0489 8.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
