Manual

could affect picture quality If you still experience
problems even when you connect your system
directly to you! TV, tl), connecting yore system to
your TV's S video input (page 19, 23).
Even though you set the aspect ratio in [TV
TYPE] of [SCREEN SETUP], the picture does
not fill the screen.
• The aspect ratio on the disc is fixed.
Sound
There is no sound.
• The speaker cord is not connected securely.
• Press MUTING on the lemote if "MUTING ON"
is displayed in the front panel display.
• The system is in pause mode or in Sitar-motion
Play mode Press [2> to return to nolanal play
mode
• Fast forward or thst reverse is perfolmed. Press
[2> to re0un to nolmal play mode.
• Check the speaker settings (page 76).
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected conectly and securely
There is no sound from the subwoofer.
• Check the speake! connections and settings
(page 14 76).
• Set the sound field to "AUTO FORMAT DIRECT
AUTO" (page 55)
Severe hum or noise is heard.
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away fiom a
transforlner or motor, and at least 3 meters (10 It)
away fioln your TV set or a fluorescent light.
• Move your TV away flora the mldio components.
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcotml.
• Clean tile disc.
The sound loses stereo effect when you play a
VIDEO CD, a CD, or an MP3.
• Set [AUDIO] to [STEREO] by pressing AUDIO
(page 53)
• Make stue the system is connected properly
The surround effect is difficult to hear when
you are playing a Dolby Digital, DTS, or MPEG
audio sound track.
• Make sine tile somld field fimction is on (page 55).
• Check the speaker connections and settings (page
14, 76).
• Depending on tile DVD, the output signal may not
be the entire 5.1 channel. It may be monaural or
stereo even if the sound tlack is recorded in Dolby
Digital or MPEG mldio tblmat
The sound comes from the center speaker
only.
• Depending on the disc the sound may come flora
the cente! speake! only.
No sound is heard from the center speaker.
• Check the speake! connections and settings
• Make sure tile solmd field function is on (page 55).
• Depending on the source, the effect of the
sunotmd speakers may be less noticeable.
No sound or only a very low-level sound is
heard from the surround speakers.
• Check the speake! connections and settings.
• Make sure the solmd field function is on (page 55).
• Depending on the source, the effect of the
sunotmd speakers may be less noticeable.
Operation
Radio stations cannot be tuned in.
• Check that the antenna (aerial) is connected
seculely Adjust the antenna (aerial) o! comiect an
extelnal antenna (aerial) if necessary.
• The signal strength of the stations is too weak
(when tuning in with automatic iaming) Use direct
tuning.
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 67)
• Press DISPLAY so that the frequency appears in
the front panel display.
The remote does not function.
• There are obstacles between the relnote and tile
system.
• The distance beiween the remote and the system is
too far.
• The remote is not pdiilted at the remote sensor on
the system.
• The batteries in the remote are weak.
The disc does not play.
• There is no disc inse_ted
• The disc is upside down
Inselt the disc with the playback side facing down
• The disc is skewed on the disc tray.
• The system cannot play CD-ROMs, etc. (page 7)
• The region code on the DVD does not match tile
system.
IZ
con_nued
81G8