CV.book Page i Thursday, November 30, 2000 2:13 PM Digital Network Receiver TM Hardware Setup Instructions DHG-M55CV © 2000 by Sony Corporation. Reproduction in whole or in part without written permission is prohibited. All rights reserved.
CV.book Page ii Thursday, November 30, 2000 2:13 PM Sony Software License Agreement ATTENTION: USE OF THE SOFTWARE IS SUBJECT TO THE SONY SOFTWARE LICENSE TERMS SET FORTH BELOW. USING THE SOFTWARE OR THE PRODUCT IN WHICH IT IS INCORPORATED INDICATES USER’S ACCEPTANCE OF THESE LICENSE TERMS. IF THE USER DOES NOT ACCEPT THESE LICENSE TERMS, THE USER SHOULD IMMEDIATELY RETURN THE ENTIRE PRODUCT IN ITS ORIGINAL PACKING IN ORDER TO RECEIVE A FULL REFUND OF THE PURCHASE PRICE.
CV.book Page iii Thursday, November 30, 2000 2:13 PM WARNING Macrovision To reduce the risk of fire or shock hazard, do not expose the unit to rain or moisture. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited pay-perview uses only unless otherwise authorized by Macrovision.
CV.book Page iv Thursday, November 30, 2000 2:13 PM Safety ❑ Operate the unit only on AC 60 Hz 110-120 V. ❑ The plug is designed, for safety purposes, to fit into the wall ❑ outlet only one way. If any liquid or solid object should fall inside the cabinet, unplug the unit immediately and have it checked by qualified service personnel before operating it further. Accessories Do not place the set on an unstable cart, stand, table or shelf.
CV.book Page v Thursday, November 30, 2000 2:13 PM Contents Introducing the Digital Network Receiver Unpacking........................................................... 1 Supplied Items .....................................................1 Items Supplied Separately by Cablevision............1 Optional Items .....................................................1 Front Panel ......................................................... 2 Front Panel Controls and Indicators.....................
CV.
CV.
CV.book Page 2 Thursday, November 30, 2000 2:13 PM Introducing the Digital Network Receiver Front Panel 1 2 4 5 7 MENU 3 6 8 Front Panel Controls and Indicators Control or Indicator Description 1 STANDBY 1 Switches the Digital Network Receiver between active and standby modes. 2 Affinity Card Slot The slot in which the Affinity Card is inserted. 3 Front Panel Inputs (Door) Provides convenient audio/video line inputs and a USB connector. For details, see “Front Panel Inputs” on page 3.
CV.book Page 3 Thursday, November 30, 2000 2:13 PM Front Panel Front Panel Inputs The front panel inputs are convenient for connecting audio/video components and USB peripherals to the Digital Network Receiver. 1 Connector 2 Description 1 VIDEO/AUDIO LINE IN Inputs audio and video signals from your camcorder, digital still camera, etc., using audio/video cables (see the Cablevision user guide for details).
CV.book Page 4 Thursday, November 30, 2000 2:13 PM Introducing the Digital Network Receiver Rear Panel 1 2 Connection 1 CABLE IN 2 TO TV/VCR 3 i.LINK (2) 4 VCR CONTROL 3 4 6 8 5 7 9 0 qa qf qs qd qg Description Connects to Cablevision cable network signals using an RF coaxial cable. Outputs audio (variable) and video signals to the VHF/UHF (or RF) input on your TV or VCR using an RF coaxial cable. Used for connecting i.LINK-equipped devices (see the Cablevision user guide for details).
CV.book Page 5 Thursday, November 30, 2000 2:13 PM Using the Remote Control (RM-Y806) Using the Remote Control (RM-Y806) ✍ The following describes the Sony RM-Y806 remote control. If Cablevision supplied you with a different remote control, see the manual that came with that remote for details. Buttons that are highlighted below can also be used to operate your TV and VCR after you’ve programmed the remote control. For details, see “Programming the Remote Control” on page 6.
CV.book Page 6 Thursday, November 30, 2000 2:13 PM Introducing the Digital Network Receiver Programming the Remote Control Button Description FULL TV Displays a full screen display of the last channel. Arrows (G g F f) Moves the highlight within menus and guides. OK Selects the highlighted item. BACK Displays the previous screen. FWD Displays the next screen. LAST CH Toggles between the last and current channel. DISPLAY Displays the Title Bar (see the Cablevision user guide for details).
CV.book Page 7 Thursday, November 30, 2000 2:13 PM Using the Remote Control (RM-Y806) If the component does NOT respond Try programming the remote using the other codes listed for your brand. If you still cannot get your component to respond after trying all the codes, your component may not be compatible with this remote. If this happens, you must use your component’s remote to operate it.
CV.book Page 8 Thursday, November 30, 2000 2:13 PM Introducing the Digital Network Receiver Using the Wireless Keyboard (KI-W55CV) ✍ The following describes the Sony KI-W55CV wireless keyboard. If Cablevision supplied you with a different keyboard, see the manual that came with that keyboard for details. The wireless keyboard works like a regular keyboard and has additional buttons designed to control your Digital Network Receiver.
CV.book Page 9 Thursday, November 30, 2000 2:13 PM Using the Wireless Keyboard (KI-W55CV) Button Description CABLE POWER Switches the Digital Network Receiver between active and standby modes. TV POWER Turns the TV on and off. MENU Displays the Menu screen (see the Cablevision user guide for details). VIEWER Displays the Viewer screen (see the Cablevision user guide for details). FAV Displays the Favorites screen (see the Cablevision user guide for details).
CV.book Page 10 Thursday, November 30, 2000 2:13 PM Introducing the Digital Network Receiver Programming the Wireless Keyboard The keyboard is preset at the factory to operate any Sony brand TV. If you have any other brand of TV, use the following procedures to program the keyboard to use any of the highlighted buttons shown on page 8. To program the keyboard 1 Set the keyboard’s TV/CABLE switch to TV. 2 Turn to “Wireless Keyboard Programmable Codes” on page 13, and find the 3-digit code for your TV.
CV.book Page 11 Thursday, November 30, 2000 2:13 PM Using the Wireless Keyboard (KI-W55CV) Replacing Batteries in the Keyboard When the batteries need to be replaced, insert two size AA batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Then replace the battery compartment lid. ✍ Remove the batteries to avoid damage from possible battery leakage whenever you anticipate that the keyboard will not be used for an extended period.
CV.
CV.book Page 13 Thursday, November 30, 2000 2:13 PM Wireless Keyboard Programmable Codes Wireless Keyboard Programmable Codes TV Codes Manufacturer Code Manufacturer Code Sony 101, 074, 077 NEC Admiral 102, 114, 109,055 Panasonic 103, 112, 001, 005, 006, 008, 020, 075, 025 118, 116, 117, 107, 064, 072, 058, 082, 140 Akai 103, 020, 006 Philco 113, 103, 001, 008, 088, 061, 006, 090, 050, 012, 098, 092, 100, 082, 020 Bell & Howell (Mont.
CV.
CV.book Page 15 Thursday, November 30, 2000 2:13 PM Connecting the Digital Network Receiver Overview This chapter includes illustrated instructions for setting up your Digital Network Receiver: To Connect See Page TV with RF Connector Only 16 TV and VCR with RF Connectors Only 17 TV with A/V Connectors 18 TV and VCR with A/V Connectors 19 Home Entertainment System 21 You can connect the Digital Network Receiver in a variety of configurations.
CV.book Page 16 Thursday, November 30, 2000 2:13 PM Connecting the Digital Network Receiver TV with RF Connector Only 1 Connect the coaxial cable from the wall outlet (Cablevision cable network signal) to the Digital Network Receiver’s CABLE IN jack. 2 Connect the Digital Network Receiver’s TO TV/VCR jack to the TV’s VHF/UHF IN (or RF IN) jack. 3 Connect one end of the AC power cord to the Digital Network Receiver’s AC IN jack, then connect the plug end to an AC outlet.
CV.book Page 17 Thursday, November 30, 2000 2:13 PM Connecting the Digital Network Receiver TV and VCR with RF Connectors Only 1 Connect the coaxial cable from the wall outlet (Cablevision cable network signal) to the Digital Network Receiver’s CABLE IN jack. 2 Connect the Digital Network Receiver’s TO TV/VCR jack to the VCR’s VHF/UHF IN (or RF IN) jack. 3 Connect the VCR’s VHF/UHF OUT (or RF OUT) jack to the TV’s VHF/UHF IN (or RF IN) jack.
CV.book Page 18 Thursday, November 30, 2000 2:13 PM Connecting the Digital Network Receiver TV with A/V Connectors 1 Connect the coaxial cable from the wall outlet (Cablevision cable network signal) to the Digital Network Receiver’s CABLE IN jack. 2 Connect the Digital Network Receiver’s LINE OUT 1 (TV) AUDIO /VIDEO jacks to the TV’s AUDIO/VIDEO IN jacks. 3 Connect one end of the AC power cord to the Digital Network Receiver’s AC IN jack, then connect the plug end to an AC outlet.
CV.book Page 19 Thursday, November 30, 2000 2:13 PM Connecting the Digital Network Receiver TV and VCR with A/V Connectors See the illustration on the next page for details. 1 Connect the coaxial cable from the wall outlet (Cablevision cable network signal) to the Digital Network Receiver’s CABLE IN jack. 2 Connect the Digital Network Receiver’s LINE OUT 1 (TV) AUDIO /VIDEO jacks to the TV’s AUDIO/VIDEO IN jacks.
CV.
CV.book Page 21 Thursday, November 30, 2000 2:13 PM Connecting the Digital Network Receiver Home Entertainment System Connecting a Hi-Fi TV, Hi-Fi VCR, and an Audio/Video Receiver See the illustration on the next page for details. 1 Connect the coaxial cable from the wall outlet (Cablevision cable network signal) to the Digital Network Receiver’s CABLE IN jack. 2 Connect the Digital Network Receiver’s LINE OUT 1 (TV) AUDIO /VIDEO jacks to the A/V Receiver’s AUDIO/VIDEO IN jacks.
CV.
CV.book Page 23 Thursday, November 30, 2000 2:13 PM Connecting the Digital Network Receiver Setting Up the Remote Receiver The optional Remote Receiver enables you to place the Digital Network Receiver out of sight, such as behind a cabinet door. Once the Remote Receiver is set up, the infrared signals are sent from your remote control or wireless keyboard to the Digital Network Receiver via the Remote Receiver.
CV.
CV.book Page 25 Thursday, November 30, 2000 2:13 PM Other Information Troubleshooting Problem Possible Remedies Cannot display cable channels If you connected the Digital Network Receiver to your TV with an RF connection (as described on page 16) you need to tune your TV to channel 3 in order to see cable channels.
CV.book Page 26 Thursday, November 30, 2000 2:13 PM Other Information Changing the Digital Network Receiver’s RF Output Channel If you connected the Digital Network Receiver to your TV or VCR using an RF connection (as described on pages 16 and 18), you need to set the RF output channel of the Digital Network Receiver to match the RF channel (channel 3 or 4) of the cable service provided in your area. The Digital Network Receiver is shipped with its RF output channel set to channel 3.
CV.book Page 27 Thursday, November 30, 2000 2:13 PM Other Information Specifications Inputs and Outputs Cable In To TV/VCR Video Input Output Input Output Audio Input Output Input/Output Input/Output i.
CV.
CV.book Page 29 Thursday, November 30, 2000 2:13 PM Other Information I REMOTE RECEIVER connector i.
CV.
CV.
CV.