DIGITAL VIDEOCASSETTE RECORDER DVW-M2000 DVW-M2000P DVW-2000 DVW-2000P Note The supplied CD-ROM includes operation manuals for the DVW-2000 series of digital videocassette recorders (English, Japanese, French and German versions). For more details, see page 1-5 “Using the CD-ROM Manual.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité. Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.
AVERTISSEMENT: CET AVERTISSEMENT EST VALABLE POUR LES AUTRES PAYS. 1. Utiliser un cordon d’alimentation approuvé (conducteur d’alimentation 3 âmes)/connecteur d’appareil/prise avec contacts de mise à la terre conforme aux règles de sécurité de chaque pays si applicable. 2. Utiliser un cordon d’alimentation approuvé (conducteur d’alimentation 3 âmes)/connecteur d’appareil/prise conforme aux valeurs nominales (tension, ampérage) correctes.
Table of Contents Chapter 1 Overview 1-1 Features ........................................................................................... 1-1 1-2 Example System Configuration .................................................... 1-4 1-3 Using the CD-ROM Manual .......................................................... 1-5 1-3-1 CD-ROM System Requirements ............................................ 1-5 1-3-2 Preparations ............................................................................
Table of Contents Chapter 5 Editing (Continued) 5-2 DMC Editing ................................................................................. 5-11 5-2-1 Overview of DMC Editing ................................................... 5-11 5-2-2 Carrying Out DMC Editing.................................................. 5-12 5-3 Special Automatic Editing Methods ........................................... 5-13 5-3-1 Quick Editing .......................................................................
-1 Chapter 11 Function Menu 11-1 Overview of the Function Menu ............................................... 11-1 11-1-1 Function Menu Configuration ........................................... 11-1 11-1-2 Using the Function Menu .................................................. 11-2 11-2 Function Menu Item List ...........................................................
1-1 Features lightweight, and low power consumption design. It not only offers recording and playback in digital Betacam format, but can also play back tapes recorded in Betacam SX format, analog Betacam format, or MPEG IMX format 1).
1-1 Features Chapter 1 Overview High-performance heads and compatibility playback function The newly developed high-performance heads and dynamic tracking (DT) technology provide highdensity recording and playback in narrow tracks with high reliability.
Wide range of editing functions By combining two units, you can carry out both assemble editing and insert editing automatically. All of the necessary editing functions are provided to set and amend edit points, to preview and review results of editing, and so on. DMC editing This allows automatic editing with a varying playback speed memorized beforehand for an edit segment. Split editing Cross-fade editing In audio editing, to avoid unnatural effects at edit points, you can fade the audio track.
1-1 1-2Features Example System Configuration Chapter 1 Overview The following conceptual diagram shows an example of use.
1-3 Using the CD-ROM Manual The following are required to access the supplied CDROM disc. • Computer: PC with Intel Pentium CPU - Installed memory: 64 MB or more - CD-ROM drive: × 8 or faster • Monitor: Monitor supporting resolution of 800 × 600 or higher • Operating system: Microsoft Windows Millennium Edition, Windows 2000 Service Pack 2, Windows XP Professional or Windows XP Home Edition When these requirements are not met, access to the CD-ROM disc may be slow, or not possible at all.
2-1 Control Panels Upper control panel (see page 2-2) Z VID. IN PB/EE CONFI CTL/TC MENU TCGSET PB Y-R,B OFF TC Lower control panel (see page 2-3) CONTROL PANEL KEY INHI ON OFF PANEL SEL REAR Switch panel (access by opening the lower control panel) (see page 2-14) FRONT Lower control panel unlock buttons Pushing in these buttons allows you to open the lower control panel.
2-1 Control Panels 2-1-1 Upper Control Panel Chapter 2 Location and Function of Parts 1 POWER switch 2 REMOTE buttons and RS-232C indicator 3 EJECT button 4 Format indicators BETACAM/SP POWER REMOTE 1(9P) 2(50P) RS-232C BETACAM SX MPEG IMX Cassette compartment Digital BETACAM EJECT Z PHONES 5 PHONES jack and control 1 POWER switch Pressing the ‘ ) ’ side of the switch powers the unit on.
2-1-2 Lower Control Panel Chapter 2 Location and Function of Parts 4 Time data/menu display section (see page 2-7) 2 CHANNEL CONDITION indicator (see page 2-6) 1 Audio control section (see page 2-4) 5 MULTI CONTROL knob and SHIFT indicator (see page 2-8) 6 RESET button (see page 2-8) 3 Menu control buttons (see page 2-6) VID.
2-1 Control Panels 1 Audio control section Chapter 2 Location and Function of Parts 1 Audio selection function selector buttons 2 DISPLAY FULL/FINE button 3 Audio setting display section 4 Audio signal selection buttons MIXING (mixing setting mode) button: Pressing this button puts the unit into mixing setting mode. In the audio setting display section, the MIX indicator flashes.
3 Audio setting display section Input signal indicator MIX indicator OVER indicator Level meter SDI AES/EBU/ANA DATA 5 6 7 8 MIX 1 2 3 4 dB OVER dB 20 0 2 10 -10 1 Input channel indicator -20 0 -1 -10 -30 -20 -40 -2 -40 -60 L EMPH R Monitor channel L and R indicators EMPH indicator Input signal indicator: Indicates the currently selected input signal (‘SDI’, ‘AES/EBU’, ‘ANA’ for analog) for the corresponding audio input channel.
2-1 Control Panels Note Chapter 2 Location and Function of Parts Before selecting signals from two input channels for recording in one recorder channel, check to be sure that the emphasis settings (ON or OFF) of the two input channels are the same. Recording and playback of mixed signals cannot be carried out correctly if the emphasis settings are different. For audio tracks with emphasis on, the EMPH indicator in the audio setting display section lights.
Overview of the function menu The function menu provides convenient access to frequently used function settings, such as input video signal selection and time code settings. For details on the function menu, see Chapter 11. 4 Time data/menu display section 2F 01:23:45:06 Time data type indicator This indicates the type of data displayed in the time data display area 1.
2-1 Control Panels Chapter 2 Location and Function of Parts CONFI (ON)/PREREAD indicators These indicate the state of the VTR CONFI playback 1) function. When the CONFI playback function is enabled by the setting in function menu HOME page, the CONFI indicator appears, and when CONFI playback is actually being carried out the ON indicator also appears. When F6 (PREREAD) is set to ON in function menu page 4, the CONFI playback function is disabled and one of the following is displayed.
Playback modes using the search dial Playback mode Operations and functions Press the SHUTTLE button or the search dial so that the SHUTTLE button lights, then turn the search dial. Playback is carried out at a speed determined by the position of the search dial. The playback speed range is as follows: Shuttle For details of playback in shuttle mode, see the description of the search dial 5. 2 JOG button To use the search dial for playback in jog mode, press this button, turning it on.
2-1 Control Panels 8 REC INHI (recording inhibit) indicator Chapter 2 Location and Function of Parts This indicator is on or off according to the combination of the F5 (RECINH) setting on function menu page 4 and the record inhibit plug on the cassette, as shown in the following table. When this indicator is on, recording on tape is prohibited.
Fault display function The STOP button flashes in the following cases related to reference signals: • When F2 (OUTREF) is set to INPUT on function menu page 4, and there is no input video signal. • When F2 (OUTREF) is set to REF in function menu page 4, and there is no external reference signal input or the input external reference signal is not synchronized to the input video signal. 6 F FWD (fast forward) button To fast forward the tape, press this button, turning it on.
2-1 Control Panels Chapter 2 Location and Function of Parts KEY INHI (inhibit) indicator This indicator lights when the KEY INHIBIT switch on the switch panel (see page 2-14) is set to ON. qs PLAYER button and RECORDER button When you carry out editing using a VTR connected to the REMOTE 1-IN(9P) or REMOTE 1-OUT(9P) connector (see page 2-18) as the player and this unit as the recorder, these buttons select which VTR the editing control buttons and tape transport buttons on this unit control.
3 MARK button Hold this button down for 2 seconds or more, to enable writing, amending, and deleting of shot marks. 6 REVIEW button Use this button to review the editing results after carrying out automatic editing. 7 AUTO (automatic) EDIT button After edit point setting, to carry out automatic editing (recording), press this button, turning it on. If the IN point is not set, the automatic editing is carried out with the point where you pressed this button as the IN point.
2-1 Control Panels 2-1-3 Switch Panel Chapter 2 Location and Function of Parts To access the switch panel, open the lower control panel. On how to open the lower control panel, see the figure on page 2-1. CONTROL PANEL KEY INHI ON OFF PANEL SEL REAR FRONT 4 CONTROL PANEL connector 3 PANEL SELECT switch 2 KEY INHIBIT switch 1 Memory stick slot 1 Memory stick slot Use this to update the firmware. You can also save or load setup menu settings onto the Memory Stick.
2-2 Connector Panel 2 Analog video input/output section (see page 2-16) Cooling fan Chapter 2 Location and Function of Parts 1 Analog audio input/output section 3 Digital audio input/output section (see page 2-16) 75Ω 75Ω 4 Digital signal input/ output section (see page 2-17) Cooling fan 5 Power supply section (see page 2-17) 7 Time code input/output section (see page 2-18) 6 External device connectors (see page 2-17) 8 Audio monitor signal output section (see page 2-18) 2 AUDIO INPUT CH1 to C
2-2 Connector Panel 2 Analog video input/output section Chapter 2 Location and Function of Parts 1 REF.VIDEO INPUT connectors and 75 Ω termination switch 2 COMPOSITE VIDEO INPUT connectors and 75 Ω termination switch 5 COMPOSITE VIDEO OUTPUT connectors (BNC type) These connectors output analog composite video signals. When the setting of F4 (CHARA) in function menu page 4 is ON, connector 3 (SUPER) outputs a signal with superimposed time code, menu settings, alarm messages, and other text information.
4 Digital signal input/output section 5 Power supply section Chapter 2 Location and Function of Parts SDI INPUT 1 AC IN connector 1 SDI INPUT connectors 2 Ground terminal SDI 1 AC IN connector Use a power cord to connect this to an AC outlet. OUTPUT 1 2 2 SDI OUTPUT connectors 3(SUPER) 2 Ground terminal Connect this to ground. 6 External device connectors 1 SDI (Serial Digital Interface) INPUT connectors (BNC type) Input D1 format digital video/audio signals.
2-2 Connector Panel Chapter 2 Location and Function of Parts 2 CONTROL PANEL connector (round type, 10pin) In addition to the lower control panel, a similar control panel can be connected to this unit. To connect such a second control panel, use this connector. When two control panels are connected, use the PANEL SELECT switch on the switch panel (see page 2-14) to specify which control panel will control this unit.
3-1 Connections to External Devices shows the connections with a MSW-A2000/A2000P/ M2000/M2000P/2000/2000P unit as a player, with this unit used as recorder. This unit can input serial digital signals (video and audio) from another digital VTR such as the MSWA2000/A2000P/M2000/M2000P/2000/2000P and DVW-A500/A500P/500/500P. The following example Reference signal 75 Ω termination switch: OFF REF.
3-1 Connections to External Devices 3-1-2 Connections to Analog Devices The following example shows the connections with an analog VTR (a Betacam SP VTR, D2 VTR, 1-inch VTR, etc.) for recording analog audio and video signals. Chapter 3 Preparations Video monitor COMPONENT/ COMPOSITE VIDEO OUTPUT AUDIO INPUT CH1 to CH4 and CUE IN LEVEL switches: Set according to the analog/cue audio input level and the impedance.
3-2 Reference Signals for Video Output and Servo System This section describes how reference signals for the video output signals and servo system are selected. The output from the internal reference video signal generator is supplied to the output video signal and servo circuits as a reference signal.
3-2 Reference Signals for Video Output and Servo System 3-2-2 Reference Signal for the Servo System The VTR automatically selects either the input video signal or the output from the internal reference video signal generator as the reference signal for the servo system. Which of the two signals is selected depends on the operational status of the VTR, as shown in the following flowchart.
3-2-3 Connecting Reference Signals Connect reference signals as shown below, according to the way in which the unit is to be used. Connections for recording from a switcher or signal generator Chapter 3 Reference signal Preparations Switcher or signal generator 75 Ω termination switch: ON REF. VIDEO INPUT 75Ω SDI INPUT 75Ω DVW-M2000/M2000P/2000/2000P Connections for recording from an external VTR (player) Reference signal 75 Ω termination switch: OFF REF.
3-2 Reference Signals for Video Output and Servo System Connections for playback Reference signal Video monitor Chapter 3 75 Ω termination switch: ON REF.
3-3 Setup The principal setup operations before operating this unit can be carried out using setup menus. The setup menus of this unit comprise a basic setup menu and an extended setup menu. The contents of these menus are as follows.
3-2 Signals for Video Output and Servo System 3-4Reference Superimposed Character Information When the function menu item CHARA is set to ON, the video signal output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector or the SDI OUTPUT 3 (SUPER) connector contains superimposed character information, including time code, menu settings, and alarm messages.
2 Time code reader drop frame mark (for 525-line mode only) “.”: Indicates drop frame mode “:”: Indicates non-drop-frame mode Block B TAPE UNTHREAD Cassette is not loaded. STANDBY OFF Standby off mode T.RELEASE Tape tension released STOP Stop mode F.
3-2 Signals for Video Output and Servo System 3-5Reference Cassettes 3-5-1 Cassette Types This unit uses the following digital Betacam cassettes for both recording and playback. 3-5-2 Inserting and Ejecting Cassettes It is not possible to insert or eject a cassette unless the unit is powered on.
Removing slack from the tape Press in one of the reels with a finger, and turn gently in the direction shown by the arrows until there is no slack in the tape. Chapter 3 Preparations Ejecting a cassette Press the EJECT button. Note Ejecting is a local operation. It is not possible to eject a cassette in another unit by remote control. If the tape slacks inside the unit, pressing the EJECT button may not eject the cassette.
3-2 Signals for Video Stick Output and Servo System 3-6Reference Using a Memory When a Memory Stick (option) is inserted in the VTR, the file data can be stored on the Memory Stick, which enables you to share data among VTRs. Inserting a Memory Stick Chapter 3 Insert a Memory Stick with the label side up into the Memory Stick slot until it clicks and the access lamp lights in red.
Notes Chapter 3 • Prevent metallic objects or your finger from coming into contact with the terminal of the connecting section. • Do not attach any material other than the supplied label to the label space. • Attach the label at the prescribed labeling position. Make sure the label is attached at the labeling position properly. • Do not bend, drop, or apply strong shock to a Memory Stick. • Do not disassemble or modify a Memory Stick. • Do not let the Memory Stick get wet.
4-1 Recording Chapter 4 Recording and Playback Chapter 4 Recording and Playback This section describes video and audio recording on the unit. 4-1-1 Preparations for Recording For details on each setting, see the pages indicated in parenthesis. Switch and menu settings Before beginning recording, make necessary switch and menu settings. POWER switch: ‘ ( ’ side (ON) REMOTE buttons (see page 2-2): off Audio signal selection buttons (see page 2-5): Select the audio channel to be monitored.
4-1 Recording Adjusting the audio recording levels To use the emphasis function When carrying out audio recording at a reference level Leave the REC controls pressed in. The audio signals will be recorded at a preset reference level (a reference 0 dB indication for an input of +4 dBm). To add emphasis to the analog input audio signal or analog playback audio signal, set the EMPHSS to ON (see page 11-6).
Setting the time code value to the real time With the settings in function menu page 1 set as follows, carry out the procedure under the heading above, “Setting an initial time code value”. In steps 3 and 4, set the value slightly after the current time, then carry out step 6 at the instant the real time catches up with the setting. TCG (F1): INT TCG (F2): PRESET RUN: FREE DF: DF (525/60 mode only) Setting an initial time code value Use the following procedure.
4-1 Recording To synchronize the internal time code generator to an external signal Chapter 4 Recording and Playback Use this method to synchronize the time code generators of a number of VTRs, or to record the playback time code signal from an external VTR without deterioration of the signal waveform. In this case the RUN and DF settings are ignored. You can synchronize the internal time code generator to either of the following external time codes.
To record an external time code without modification 4-1-3 Recording Procedure To record, use the following procedure. Using this method has no effect on the running of the internal time code generator. To record the playback time code from an external VTR, the method under the heading above, “To synchronize the internal time code generator to an external signal”, is recommended. Z Chapter 4 Z 1 IN TIME CODE OUT 2 For details, see the section “Inserting a cassette” (page 3-10).
4-1 4-2Recording Playback This section describes playback of video and audio. 4-2-1 Preparations for Playback For details on each setting, see the pages indicated in parenthesis. Switch and menu settings Before beginning playback, make necessary switch and menu settings. Chapter 4 POWER switch: ‘ ( ’ side (ON) Recording and Playback REMOTE buttons (see page 2-2): off Audio signal selection buttons (see page 2-5): Select the audio channel(s) to be monitored. Z VID.
Time data selection Normal playback Displayed time data Use the CTL/TC setting in function menu HOME page to select one of CTL (control), time code, and user bit values. When you select time code, the data displayed is determined by the TCR setting (LTC/AUTO/VITC) in function menu page 1 as follows. First insert a cassette.
4-2 Playback Playback in jog mode Playback in shuttle mode In jog mode, you can control the speed of playback by the speed of turning the search dial. The playback speed range is ±1 times normal speed. In shuttle mode, you can control the speed of playback by the angular position of the search dial.
To alternate between normal-speed playback and variable speed mode playback Set the search dial to the position corresponding to the desired variable playback speed, then switch between normal-speed playback and variable speed playback by pressing the PLAY and VAR buttons alternately. For intermittent variable speed mode playback, press the STOP and VAR buttons alternately.
4-2 Playback 2 When the adjustment is completed, release the PLAY button. The tape transport returns to normal speed, and the SERVO indicator comes on again. To perform continuous capstan override playback Chapter 4 Z Recording and Playback 3 1 2 2 Set setup menu item 111 (TSO PLAY) to TSO. Hold down the DMC EDIT button and turn the MULTI CONTROL knob to select the playback speed.
4-2-3 Dynamic Motion Control (DMC) Playback Overview DMC playback allows you to vary the playback speed for a certain section of a tape, in variable speed mode (from –1 to +3 times normal speed for digital Betacam playback, from –1 to +3 times normal speed for MPEG IMX playback, from –1 to +2 times normal speed for Betacam SX playback, or from –1 to +3 times normal speed for analog Betacam playback), and store the varying speed in memory for later playback at the same varying speed.
4-2 Playback 4 Holding down the DMC EDIT button, turn the search dial, to set the initial speed at the playback start point. The speed you set appears in the speed indication area. During this period the tape does not move. When the initial speed setting is complete, release the DMC EDIT button. 5 Press the PREVIEW button. Chapter 4 The tape is prerolled and played back at normal speed from the on-air start point to the speed variation start point.
To start playback immediately after preroll Press the PREVIEW button. The PREVIEW button lights, and after preroll, DMC playback is carried out for the section from the speed variation start point, then playback continues at normal speed from the speed variation end point. To stop the tape during DMC playback Press the STOP button. Chapter 4 To exit DMC playback mode Press the DMC EDIT button and the DELETE button simultaneously.
5-1 Automatic Editing Chapter 5 This section describes how to carry out automatic editing with this unit and another VTR connected to the REMOTE1-IN(9P) connector. Sequence of editing operations The following flowchart outlines the sequence of operations in automatic editing with two VTRs.
5-1 Automatic Editing 5-1-2 Switch and Menu Settings Before beginning editing, make necessary switch and menu settings. Recorder settings POWER switch: ‘ ( ’ side (ON) REMOTE buttons (see page 2-2): 1(9P) Editing mode setting section (see page 2-11): Select assemble editing or insert editing. Chapter 5 Z Editing VID.IN setting (see page 11-3): Select the input video signal. VID.
5-1-3 Selecting the Editing Mode 1 To select the editing mode Select assemble editing or insert editing. Press the RECORDER button or PLAYER button to select the VTR on which you will set the edit point. The button which you have pressed lights. ASSEMBLE button 2 INSERT buttons Z Turn the search dial in jog or shuttle mode, and position the tape at the required edit point.
5-1 Automatic Editing Note Setting split edit points In split editing, you can set the edit points for audio and video independently. Set the audio edit points with the AUDIO IN/OUT buttons, and the video edit points with the IN/OUT buttons. Note that split editing is only possible when the recording mode is insert editing. Z Chapter 5 Editing 4 1 1 2 3 Press the appropriate INSERT button (VIDEO, CH1 to CH4, CUE, or TC). The IN/OUT button flash.
When the audio IN point is not set for insert editing of audio only As long as the audio OUT point is set, the VTR is ready for preview or editing. If the audio IN point has not been set, the current tape position is automatically used as the audio IN point.
5-1 Automatic Editing 5-1-5 Modifying and Deleting Edit Points If the edit points are not set correctly, for example if an OUT point is before a corresponding IN point, the DELETE button flashes, and it is not possible to carry out a preview or editing operation. In this case, either modify the erroneous edit point, or first delete it and then enter it correctly. Deleting an edit point To delete an edit point, use the following procedure.
5-1-6 Cue-Up to Edit Points and Preroll To preroll to a position before an edit IN point or cue up to any edit point, use the following procedure. 5-1-7 Preview When you have set the edit points, the PREVIEW button flashes, indicating that you can carry out a preview. To carry out a preview, use the following procedure. Z Z Press the RECORDER button or PLAYER button to select the VTR on which you wish to operate. The button you have pressed lights.
5-1 Automatic Editing • From the OUT point to the postroll point, you can monitor the playback from the recorder. Monitor output During a preview, on a monitor connected to the recorder you can monitor the following video and audio. • From the preroll point to the IN point, you can monitor the playback from the recorder. • From the IN point to the OUT point, you can monitor the playback from the player through the recorder in E-E mode. The following figure illustrates this.
The following figure illustrates this. IN point Playback (recorder) OUT point E-E mode (player) Z Playback (recorder) Using a single monitor for video and audio on both player and recorder OUT button ENTRY button For efficient editing if only one monitor is available, use the following method. REVIEW button 1 2 3 PREVIEW button Connect the monitor to the recorder. Press the PLAYER button on the recorder.
5-1 Automatic Editing After automatic editing, to adjust the edit points and reexecute the edit Hold down the DELETE button and press the ENTRY button to recall the edit points. After adjusting the edit points, press the AUTO EDIT button to carry out the edit again. For details of how to adjust edit points, see Section 5-1-5 “Modifying and Deleting Edit Points” (page 5-6).
5-2 DMC Editing By controlling the player playback speed from the recorder you can achieve variable speed editing. 5-2-1 Overview of DMC Editing Conditions for DMC editing DMC editing can be used for insert or assemble editing, but not for audio split editing. Tape movement during DMC editing The following figure illustrates how the tapes move on the player and recorder during DMC editing.
5-2 DMC Editing 5-2-2 Carrying Out DMC Editing 7 When the initial speed setting is complete, release the DMC EDIT button. Setting the edit points and player speed 8 Press the PREVIEW button. The tape is prerolled and then the recorder starts operating at normal speed and the player at the set initial speed. Use the following procedure. 9 Z Chapter 5 2,6,7 8 4 1 5 3 6,9 Editing 1 Press the ASSEMBLE button or the desired INSERT button to select the editing mode. 2 Press the DMC EDIT button.
5-3 Special Automatic Editing Methods This section describes the following automatic editing methods: • Quick editing • Continuous editing • Standalone editing • Manual editing • Preread editing 5-3-1 Quick Editing 5-3-2 Continuous Editing After an automatic editing operation, the recorder automatically returns to the OUT point. For the second and subsequent editing operations, you can continue editing by simply specifying the IN and OUT points on the player.
5-3 Special Automatic Editing Methods 5-3-3 Standalone Editing This refers to editing using as the player an external device which cannot be controlled remotely through the REMOTE1-IN(9P) connector. For example, you can record a color bar signal from a signal generator in the joints between the scenes of an already completed tape. Carrying out standalone editing Set the IN point with neither the PLAYER button or RECORDER button lit.
Notes Set PB/EE in function menu HOME page to PB. 4 After selecting the desired insert editing mode, carry out the preread editing. 5 When the preread editing is completed, remove the connections. 6 7 Set the PREREAD to OFF. Editing 1 2 3 Chapter 5 • In preread editing, if an input video signal is used as the reference signal for the output video signal, this forms a feedback loop.
6-1 Overview Shot marks are indications at desired points on a tape which enable faster cueing. Types of shot mark This unit supports the following three types of shot mark. This chapter describes recording start marks and Shot mark type Writing on a camcorder, etc. post marks, treating them as varieties of shot marks.
6-1 6-2Overview Shot Mark Operation Menu This section describes the settings in the shot mark operation menu. Details of the shot mark operation menu Displaying the shot mark operation menu The shot mark operation menu comprises four items, G01 to G04. The detailed contents appear in the following table. With the function menu HOME page showing in the menu display, hold down the MARK button, and press the F5 (MENU) button.
6-3 Shot Mark Operations This section describes the operations concerning reading and writing shot marks. Note that the following operations cannot be carried out by remote control. 6-3-1 Reading Shot Marks To read in shot marks With a cassette loaded, hold down the LIST button and press the F FWD or REW button. Reading shot marks from more than one cassette After changing the cassettes, carry out the reading operation again.
6-3 Shot Mark Operations To write in crash recording or assemble editing Erasing a shot mark 1 Hold the MARK button down for at least 2 seconds. Select the shot mark from the shot mark list, and then carry out the deletion operation. 2 At the position you wish to write the mark, hold down the ENTRY button, and press the MARK button. A mark of the type selected in item G04 of the shot mark operation menu is written. For details of the procedure, see page 6-6.
Example of list display The following figure shows how the list is organized. Shot mark number of current cursor position / total number of stored shot marks Separator between read-in groups of shot marks Cursor (current shot mark position) Position in list SHOT MARKER (011/180) NO.
6-3 Shot Mark Operations To delete an individual shot mark Use the following procedure. 1 The REC/ERASE indicator lights, indicating that you can rewrite or erase shot marks. Z 3 1 Chapter 6 2 2 3 Display the shot mark list. 4 Press the DELETE button and MARK button simultaneously. 2 1 With the shot mark list displayed, select the shot mark to be deleted using the MULTI CONTROL knob. Shot Mark Function With the MARK button held down, press the DELETE button.
Cueing up to shot marks adjacent to the current tape position (index function) 1 In item G01 of the shot mark operation menu (page 6-2), select one of recording start mark, shot mark 1, shot mark 2, and post mark, or select all. 2 Holding down the MARK button, press the F FWD button or REW button. The tape is played back, and the shot data displayed. To delete the shot data Once again hold down the ENTRY button, and press the PLAY button.
6-3 Shot Mark Operations 6-3-6 Sorting Shot Marks Based on shot data recorded on the tape, you can separate the shot marks by cassette, and sort them in time code sequence. To sort the shot marks Use the following procedure. 1 With the shot mark list displayed, press the F5 (SETING) button. 2 Press the F2 (NEXT) button, and select SORTING LIST. 3 Press the F4 (ON) button to change the setting to ON. Sorting starts. When it ends, the setting indication returns to OFF.
7-1 Overview of Tele-File Functions Memory label Newly developed IC In Tele-File, data is managed in units called “clips.” A clip consists of the following data items, whose settings can be displayed and changed. • Cue point • Write protect • Mark • Recording start point • IN point • OUT point • Take number • Cut number • Scene number • Comment Data library management with handy reader/writer An optional handy reader/writer (supporting Memory Stick) is available to facilitate data library management.
7-1 of Tele-File 7-2Overview Opening theFunctions Tele-File Menu To open from the function menu Configuration of the Tele-File menu Display page 5 of the function menu in the menu display section, and then press the F1 (TELE-F) button. The Tele-File menu has a tree structure, as illustrated below. When the menu first opens, the menu operation mode is clip data display mode. The Tele-File menu opens. For details about the function menu, see Chapter 11 “Function Menu” (page 11-1).
7-3 Tele-File Menu 7-3-1 Clip Data Display For more information about how to display menus on the monitor, see the section “To display menus on the monitor” (page 12-2). Shown below are examples of the default menu displays in the menu display section and the monitor display.
7-3 Tele-File Menu Setting display area Displays the setting of the currently selected data type, and a cursor (“*” or “>”). The meaning of the cursor symbols is as follows: *: Indicates that the mode is clip data display mode or attribute data display/modify mode, and that data is selected. >: Indicates that the mode is clip data modify mode or attribute data display/modify mode, and prompts for data entry or modification. Menu items (functions) Display menu items (functions).
Title The title (maximum 14 characters) set in attribute data display/modify mode. Selected clip number A 4-digit number representing the number of the selected clip (with the “*” cursor). Remaining memory percentage The percentage of remaining memory (user area) available for use. If there is not sufficient free memory, the message << MEMORY FULL!!>> appears (stays lit for three seconds) in time data display area 2 when you attempt to add data.
7-3 Tele-File Menu Moving the cursor directly Regardless of the cursor’s current position, pressing one of the following buttons moves the cursor directly to the specified position in the same clip and displays the data. IN (video IN point) button: IN point data OUT (video OUT point) button: OUT point data MARK button: Cue point data To display the duration Press the IN (video IN point) and OUT (video OUT point) buttons simultaneously.
7-3-3 Modifying Clip Data To modify clip data, put the unit into clip data display mode and then press the F2 (SELECT) button to put it into clip data modification mode (the cursor changes to “>”). The function assignments for menu items in clip data modification mode are as follows. Clip data modification mode menu items Item name Function F1 (RETURN) Returns to clip data display mode. F2 (MODIFY) Changes the setting of the selected data, or makes a new setting.
7-3 Tele-File Menu To add and delete clips To set time code data To add clips Proceed as follows to make or change settings for cue point, IN point, and OUT point data. 1 2 Rotate the MULTI CONTROL knob to move the “*” cursor to the position where you want to insert the clip. Press the F2 (SELECT) button. 1 2 3 Select a clip. Select cue point, IN point, or OUT point. Press the F2 (SELECT) button. The unit enters clip data modification mode. 3 The unit enters clip data modification mode.
To set the set or modified data as other time data Press the F6 (SET TO) button and select the time data (cue point, IN point, or OUT point), and then press the F5 (SET) or F6 (SET NL) button. The position where the data is set differs as follows, depending on the button pressed. • F5 (SET): The data is set in the selected time data position. • F6 (SET NL): A new clip is added at the lowest line and the time data is set at the selected data position in the new clip.
7-3 Tele-File Menu To make comment settings Proceed as follows to make comment settings. 1 2 3 Select a clip. Select comment. Press the F2 (SELECT) button. The unit enters clip data modification mode. 4 Press the F2 (MODIFY) button. The data entry area begins to flash, and the data can be set. Enter a character by rotating the MULTI CONTROL knob. 6 Press F4 (t) button to move to the next character place. 7 Repeat steps 5 and 6 until you have entered the entire comment.
7-3-5 Displaying and Modifying Attribute Data You can display and modify attribute data. The example below shows attribute data displayed on the monitor. Video final recording date Title ID Administrator data Model name Serial number Write inhibit setting Thread count Number of cue points TELE-FILE INFORMATION *REC DATE 2001/07/21 TITLE TEST 01 ID ADMIN MODEL SERIAL 00000 WRITE INHIBIT OFF THREAD COUNT 00012 CUE POINT No.
7-3 Tele-File Menu To modify attribute data You can modify the title, ID, administrator data, and write inhibit setting attributes. However, the attributes cannot be modified when the write inhibit setting is ON. Proceed as follows after setting the write inhibit setting to OFF. 1 Rotate the MULTI CONTROL knob to select the item. The F2 (SELECT) button is enabled when you select an item that can be modified (title, ID, administrator data, and write inhibit setting). 2 Press the F2 (SELECT) button.
8-1 Overview of UMID Functions UMID Basic device that recorded the material and whether the material is the original or a copy. The Source Pack section contains information about when/where/who recorded the material. A UMID with a Basic section only is called a Basic UMID. A UMID with both Basic and Source Pack sections is called an Extended UMID. The following figure shows a general overview of the information contained in a UMID.
8-1 of UMID Functions 8-2Overview Recording UMIDs UMIDs can be recorded when recording video signals with this unit. You can select whether to inherit (copy) the UMID contained in input signals, or automatically or forcibly generate a new UMID. Selecting the type of UMID to record Select whether to record a Basic UMID or an Extended UMID by using setup menu item 655 UMID RECORDING.
Time zone settings ITEM-029 STORED OWNERSHIP COUNTRY ORGANIZATION *USER 2 The UMID uses the UTC (Coordinated Universal Time) time standard. Setting this unit’s built-in calendar clock to the local time, and then setting a time zone to indicate the difference from global UTC standard time allows correct UMIDs to be generated. To set the time zone, display the HOME page of the function menu and proceed as follows.
8-1 of Output UMID Functions 8-3Overview UMID and Display This section explains how to output and display UMIDs. UMID display on the video monitor 8-3-1 UMID Output Settings You can choose to output UMIDs or not, and select either Basic UMID or Extended UMID when you choose to output UMIDs. Make these settings using setup menu item 651 UMID OUTPUT. See page 12-18 for more information about setup menu item 651.
Note The function for converting unit count to UTC works only when the unit rate is 2 (24 frames), 3 (24/1.001 frames), 4 (25 frames), 6 (30 frames), or 7 (30/1.001 frames). For other unit rates, the unit rate number and unit rate are displayed in hexadecimal. Chapter 8 5 Altitude XXXXXXXXm: Altitude data indicating the distance from the center of the earth is displayed in this format. S+XXXXXXXm Y+D: Altitude data indicating the distance from sea level is displayed in this format.
9-1 Overview of Essence Mark Functions Chapter 9 Essence Marks An essence mark uses a term value dictionary item as defined in the SMPTE RP210A Metadata Dictionary to express and transfer points such as recording start points and edit point candidates in up to 32 bytes of data. The basic format of the SMPTE RP210A Metadata Dictionary is defined in SMPTE 336M Data Encoding Protocol using Key-Length-Value (KLV coding specifications).
9-1 Übersicht über dieMark Essenzmarken-Funktionen 9-2 Essence Recording and 9-2-1 Essence Mark Recording Essence marks contained in SDI input signals and essence marks generated by this unit can be recorded to tape together with video signals. All essence mark data generated by this unit is 7-bit ASCII codes. The generation period is 1 frame. Selecting the SDI VANC line into which to insert essence marks You can select the SDI signal VANC line into which essence marks should be inserted.
10-1 Overview of Auto Event Detector Functions See Chapter 9 for more information about essence marks, and see Chapter 7 for more information about the Tele-File functions. Note Events are output about 3 frames after the actual locations of the events. 10-2 Event Output and Recording Outputtting events converted into essence marks You can select whether or not to convert into essence marks and output events detected by the AED during playback (normal playback, variable speed playback, and jog playback).
11-1 Overview of the Function Menu 11-1-1 Function Menu Configuration The function menu consists of six pages by factory default: the HOME page and five pages numbered 1 to 5. You can also display the HOME2 page by setting user-defined function keys. The following icons appear at the left edge of the menu display section to denote the current page. 1 : HOME page 1: Page 1 2: Page 2 3: Page 3 HOME2 page (user-defined function keys) Up to six function keys can be defined (i.e.
11-1 Overview of the Function Menu Chapter 11 11-1-2 Using the Function Menu Function Menu To change a menu item setting To change a menu item setting, press the corresponding function button (F1 to F6) to display the desired setting in the lower part of the menu display. Each press of the button displays the next setting. When a menu item setting flashes Menu item settings flash to inform you that you can change the setting value by rotating the MULTI CONTROL knob.
11-2 Function Menu Item List Chapter 11 The function menu has the following items. Function Menu HOME page Item Setting F1 (VID.IN) Selects the input video signal. COMPST: Analog composite signal Y-R,B: Analog component signal SDI: SDI signal SG (normally not displayed): Test signal from the internal test signal generator (For details, see setup menu item 710 on page 12-22.) F2 (PB/EE) Selects the video and audio signals output during fast forward, rewind, stop, and standby.
11-2 Function Menu Item List Chapter 11 Page 1 Function Menu Item Setting F1 (TCG) Selects the time code to use. INT: Time code generated by the internal time code generator EXT: One of the following time codes • When F6 (TCR) is set to LTC or AUTO, the external time code input from the TIME CODE IN connector • When F6 (TCR) is set to VITC, the VITC time code of the input video signal RP188: Synchronize the internal time code generator with the SMPTE RP188 time code contained in the SDI input signal.
Chapter 11 Page 2 Setting F1 (V.PROC) Selects the control method for the internal digital video processor. Function Menu Item LOCAL: Change the settings of the internal digital video processor by using this function menu. REMOTE: Use the optional BVR-50/50P Remote Control Unit to control the internal digital video processor. MENU: Change the settings of the internal digital video processor by using the MENU of the HOME page. F2 (VIDEO) Sets the video signal output level (–∞ to +3 dB).
11-2 Function Menu Item List Chapter 11 Page 3 Function Menu Item Setting F1 (SYNC) Sets the output signal sync phase. Setting method With the displayed setting flashing, you can rotate the MULTI CONTROL knob to adjust the output signal sync phase across the range ±15 µs relative to this unit’s input reference signal.
Chapter 11 Page 4 Setting F1 (CAPSTN) Selects the number of fields for capstan lock in playback and editing. Function Menu Item For DVW-M2000/2000 2F: The capstan servo locks in units of 2 fields. • For tape output, color framing may not match the reference signal selected with the F2 (OUTREF). • In assemble editing, color framing may be non-continuous at edit points. When playing back a tape that was recorded with composite source signals, a vertical shift in the video (H shift) occurs.
11-2 Function Menu Item List Chapter 11 Item Setting Function Menu F5 (RECINH) Specifies whether or not to inhibit recording to tape. ON: Inhibit recording to tape depending on the setting of setup menu item 310. OFF: Do not inhibit recording to tape. F6 (PREREAD) Specifies whether or not to preread (read before write) in insert editing. ON: Preread depending on the setting of setup menu item 319. OFF: Do not preread. Page 5 Item Setting F1 (TELE-F) Displays the Tele-File menu.
12-1 Setup Menu Configuration Configuration of the extended setup menu The extended setup menu comprises the following groups of items. Item group Function Refer to Items 100 to 199 Settings relating to control panels Page 12-8 For details, refer to the Installation Manual. Items 200 to 299 Settings relating to the remote control interface Page 12-11 In this manual, both the basic setup menu items and extended setup menu items are also referred to simply as setup menu items or menu items.
12-2 Menu Operations 12-2SetupSetup Menu Operations To display setup menus Chapter 12 MULTI RECORDER CONTROL ASSEMBLE VIDEO TC CH1 CH2 CH3 CH4 CUE PUSH/ SHIFT Setup Menus CHANNEL CONDITION VID.
To display a desired sub-item For a menu item having sub-items, you can select a desired sub-item as follows. With a desired menu item selected, press the F2 (SELECT) button. 2 1 Turn the MULTI CONTROL knob to select a desired sub-item. The current setting of the sub-item flashes. 2 Changing menu item setting values The procedures for changing menu item setting values or sub-item setting values are described below.
12-2 Setup Menu Operations Resetting the menu settings to their factory default values (menu item B20) Recall (B01) Save Chapter 12 Current active menu settings Save (B11) Menu bank 1 To reset the current active menu settings to their factory default values, proceed as follows. Setup Menus 1 Perform steps 1 to 3 of the procedure described in the section “To change the settings of menu items without sub-items” on page 12-3 to set menu item B20 RESET SETUP to ON.
12-3 Items in the Basic Setup Menu The basic setup menu contains the following items. In the “Settings” column of the table, the factory default settings are indicated by an enclosing box. 001 PREROLL TIME 0S ... 5S ... 30S: Set the preroll time to between 0 and 30 seconds. A preroll time of at least 5 seconds is recommended when using this unit for editing.
12-3 Items in the Basic Setup Menu Item number Item name 009 a) Settings Determines the type of characters such as time code output from the COMPOSITE VIDEO OUTPUT 3 (SUPER) connector and the SDI OUTPUT 3 (SUPER) connector for superimposed display on the monitor.
023 Sub-item When MAP is selected in menu item 006, the buttons that can be operated on the control panel of this unit when it is being controlled by remote control from another device can be selected from the following sub-items. The settings of each sub-item are as follows. DIS : Do not function. ENA: Function. 1 STOP Select whether the STOP button functions. 2 PLAY Select whether the PLAY button functions. 3 REC/EDIT Select whether the REC and EDIT buttons function.
12-4 in the Extended Setup Menu 12-4ItemsItems in the Extended The extended setup menu contains the following items. Setup Menu In the “Settings” column of the table, the factory default settings are indicated by an enclosing box. Chapter 12 Menu items in the range 100 to 199, relating to the control panels Setup Menus Item number Item name Settings 101 SELECTION FOR SEARCH DIAL ENABLE Select how the unit enters the search mode.
Menu items in the range 100 to 199, relating to the control panels (Continued) Item number Item name Settings Select whether or not to flash the REC INHI indicator when the function menu item RECINH is set to OFF and the record inhibit plug on the cassette is pressed in. OFF : Do not flash the REC INHI indicator. ON: Flash the REC INHI indicator.
12-4 Items in the Extended Setup Menu Menu items in the range 100 to 199, relating to the control panels (Continued) Item number Item name Settings Chapter 12 118 KEY INHIBIT SWITCH EFFECTIVE AREA Sub-item Select which switches and buttons can be operated when the KEY INHIBIT switch on the switch panel is set to ON. The following sub-items control different sets of switches and buttons independently.
Menu items in the range 100 to 199, relating to the control panels (Continued) Item number Item name Settings Selects the device used for data modification operations in the Tele-File menu. CONTROL PANEL : Operate with the control panel of this unit. REMOTE: Operate with remote devices connected to connectors such as REMOTE1, REMOTE2, and RS-232C. 134 TELE-FILE MENU AUTO POPUP Selects whether to open the Tele-File menu automatically when a cassette with a Tele-File label is loaded.
12-4 Items in the Extended Setup Menu Item number Item name Menu items in the range 300 to 399, relating to editing operations Settings Chapter 12 VAR SPEED RANGE FOR Select the playback speed range when carrying out playback in variable speed SYNCHRONIZATION mode from a remote control unit connected to the REMOTE 1-IN(9P) connector or REMOTE 1-OUT (9P) connector.
Menu items in the range 300 to 399, relating to editing operations (Continued) Item number Item name Settings Select the STD or NON-STD mode in accordance with a composite video input. AUTO : Detect automatically whether the input video luminance and chrominance signals are interleaved or not. If they are interleaved, select the STD mode. If they are not interleaved, select the NON-STD mode. STD: The STD mode is always used (forced STD mode).
12-4 Items in the Extended Setup Menu Menu items in the range 300 to 399, relating to editing operations (Continued) Item number Item name Settings Chapter 12 316 CONFIDENCE PB MODE Setup Menus Sets F3 (CONFI) in function menu HOME page to ENABLE. For settings of F3 (CONFI), see page 11-3. mode1: The CONFI playback function is only enabled during recording. mode2 : The CONFI playback function is also enabled during normal playback with the edit preset function being on, as well as during recording.
Menu items in the range 400 to 499, relating to preroll Settings Item number Item name FUNCTION MODE AFTER CUEUP Select the state that the unit goes into after a cuing-up operation. STOP : Stop (the “stop mode”) STILL: Still playback (in search mode) 402 TIME REFERENCE FOR PREROLL When prerolling a tape with time code discontinuities, select whether or not to use CTL pulses to count time code from before a discontinuity. CTL : Use CTL pulses to count time code.
12-4 Items in the Extended Setup Menu Menu items in the range 600 to 699, relating to the time code generator Chapter 12 Item number Item name Settings 601 In 525-line mode Select a line to insert the VITC in. 12H ... 16H ... 20H: Select any line from 12 to 20. VITC POSITION SEL-1 Setup Menus Note You can insert the VITC signal in two places. To insert it in two places, set both items 601 and 602. In 625-line mode Select a line to insert the VITC in. 9H ... 19H ...
Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number Item name Settings Select the signal output from the TIME CODE OUT connector during normal (×1) speed playback in the following cases: • For tape playback when the function menu item TCG (F1) is set to INT and TCG (F2) set to REGEN. • For preroll or postroll playback during automatic editing with the tape. TAPE: During tape playback, the playback time code signal is output without regeneration.
12-4 Items in the Extended Setup Menu Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number Item name Settings Chapter 12 REGEN CONTROL MODE In editing performed using the control panel of this unit, select whether or not the time code is automatically regenerated.
Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number Item name Settings Select whether to inherit the UMID in the input signal when recording a UMID. INPUT : Inherit the UMID in the input signal, if it is present. • Even when INPUT is selected, a new UMID is generated if the input signal does not contain UMID data (the same behavior as when NEW is selected).
12-4 Items in the Extended Setup Menu Menu items in the range 600 to 699, relating to the time code generator (Continued) Item number Item name Settings Chapter 12 ESSENCE MARK INPUT RECORD Select whether or not to record essence marks contained in the video input. off : Do not record. on: Record. 662 ESSENCE MARK SELF RECORD Select whether or not to record to tape essence marks generated by this unit when recording video.
Item number Item name Menu items in the range 700 to 799, relating to video control Settings In E-E mode the video signal is output delayed with respect to the video input signal by the time for video circuit processing. With this item, select whether or not to delay the sync signal attached to the output video signal by an amount corresponding to the delay. SYNC : Delay the sync signal by the corresponding amount before attaching it. VIDEO: Attach a sync signal with the same timing as the input signal.
12-4 Items in the Extended Setup Menu Menu items in the range 700 to 799, relating to video control (Continued) Item number Item name Settings Chapter 12 Setup Menus 707 FORCED VERTICAL INTERPOLATION OFF The “Y-add” functiona) is normally switched on automatically during jog or variable speed playback. This item selects whether or not to force the “Y-add” function off. AUTO : Automatically switch the “Y-add” function on. OFF: Force the “Y-add” function off.
Menu items in the range 700 to 799, relating to video control (Continued) Item number Item name Settings VIDEO PROCESS ON CAP LOCK 2FIELD When the function menu item CAPSTN or menu item 106 is set to 2F for 2-field playback, select whether or not to carry out a “picture shift”. OFF : No picture shift ON: Carry out picture shift.
12-4 Items in the Extended Setup Menu Menu items in the range 700 to 799, relating to video control (Continued) (Items 715 to 721: Settings for controlling the video processing system according to the menu settings) Item number Item name Settings Chapter 12 Setup Menus 715 VIDEO GAIN CONTROL Adjust the video output level. –2048 to 0 to +848 716 CHROMA GAIN CONTROL Adjust the chroma output level. –2048 to 0 to +848 717 CHROMA PHASE CONTROL Adjust the chroma phase.
Menu items in the range 700 to 799, relating to video control (Continued) Item number Item name Settings Select the horizontal blanking width of the video output signal. NAROW : Digital blanking (narrow) WIDE: Analog blanking (wide) When WIDE is selected, the horizontal blanking width complies with RS170A, and normally the blanking is widened and the image becomes narrower.
12-4 Items in the Extended Setup Menu Menu items in the range 800 to 899, relating to audio control Chapter 12 Setup Menus Item number Item name Settings 801 DIGITAL JOG SOUND Turns the digital jog sound on and off. OFF: Digital jog sound is turned off. Audio of digital channels not subjected to speed correction is output. When the tape stops, after one second the audio is muted. ON : Digital jog sound is turned on.
Menu items in the range 800 to 899, relating to audio control (Continued) Item number Item name Settings Select the output timing of digital audio playback signals: (SDI and AES/EBU only). The reference position corresponds to a setting of 80H; when the setting is less than 80H, the output timing is advanced, and when it is higher than 80H, the output timing is delayed. (at 80H, 128 samples = approx. 2.7 ms, and 1 sample=approx. 20 µs) 0 ... 80 ...
12-4 Items in the Extended Setup Menu Menu items in the range 800 to 899, relating to audio control (Continued) Item number Item name Settings Chapter 12 823 NAU FLG PB Sub-item Setup Menus 1 CH1/CH2 2 CH3/CH4 3 CCH5/CH6 (DVW-M2000/ M2000P only) Valid only for an MPEG IMX format 8-channel recording tape 4 824 825 12-28 CH7/CH8 (DVW-M2000/ M2000P only) Valid only for an MPEG IMX format 8-channel recording tape Controls the non-audio flag when the playback format is Digital Betacam or Betacam
Menu items in the range 800 to 899, relating to audio control (Continued) Item number Item name Settings AUDIO PB VOLUME SELECT (DVW-M2000/M2000P only) Selects which PB control knobs are assigned to control playback of digital audio channels. 827 828 0 ALL CH DEFAULT : Use the following settings. CH1: Control knob 1 CH2: Control knob 2 CH3: Control knob 3 CH4: Control knob 4 CH5: Unity CH6: Unity CH7: Unity CH8: Unity UNITY: Set all channels to unity, and disable the control knobs.
12-4 Items in the Extended Setup Menu Item number Item name Chapter 12 901 Menu items in the range 900 to 999, relating to digital processing Settings VIDEO OUTPUT DATA Set the bit length for SDI video output data. 8bit: Set the bit length to 8 bits. 10bit : Set the bit length to 10 bits. Setup Menus It is recommended that you select the optimal setting for the device to which you are going to connect this unit. 903 FREEZE MODE Select the freeze mode and freeze timing. FIELD : Freeze a video field.
13-1 Overview of Setup Utility Menu Functions See Section 3-6 “Using a Memory Stick” (page 3-12) for more information about memory sticks. Refer to the Maintenance manual Volume 1 for more information about downloading, uploading, and formatting operations. To download files saved in memory sticks Proceed as follows. 1 To display the setup utility menu Press the F1 (DNLOAD) button. The menu display changes, allowing you to execute the download.
13-1 Overview of Setup Utility Menu Functions 5 Press the F5 (SET) button. ROM TO STICK SETUP MENU UPLOAD The selected file is downloaded. STICK <- VTR File: XXXXXXXX.XXX Note Chapter 13 Setup Utility Menu Functions Do not do any of the following during the download. Doing so can corrupt the ROM software of this unit, making the unit unable to download normally. • Power the unit off. • Remove or insert a memory stick. • Remove or load a cassette. EXECUTE - ON 5 Press the F5 (SET) button.
3 Press the F5 (SET) button. Formatting is executed. If you are using a new memory stick, or if an error occurs during execution of F3: FORMAT STICK, use the sub mode to format the memory stick. Chapter 13 Note Setup Utility Menu Functions All data in the memory stick is erased when you execute F3: FORMAT STICK.
14-1 Removing a Cassette When Tape Slack Occurs For details, refer to Section 1-17 in the Installation Manual. To clean the video heads and audio heads, always use the special-purpose Sony BCT-HD12CL cleaning cassette. If you insert the cleaning cassette, it is automatically ejected after a head cleaning operation which lasts for 5 seconds. Follow the instructions with the cleaning cassette carefully, as inappropriate use of the cleaning cassette can damage the heads.
14-5 Regular Checks 14-3 Error Messages This unit is equipped with a self-diagnosis function, and if a problem is detected, displays an error message in the time data display and on the monitor. If an error message appears, contact your Sony service representative. Indications in the time data display Chapter 14 If a problem is detected, the ALARM indicator in the lower control panel lights, and an error message and error code appear in time data display area 1.
Error Message List Description NO COMMUNICATION Abnormality in the interface between the lower control panel and SYS CPU (SS-89 board) has been detected in the lower control panel side. 01 REEL TROUBLE Tape slacking has been detected in the threading or unthreading operation. 02 REEL TROUBLE Tape slacking or tape breaking has been detected in the SEARCH, FF,or REW mode. 03 REEL TROUBLE Tape slacking,tape breaking,or supply or take-up reel locking has been detected in the REC or PLAY mode.
14-5 Regular Checks 14-4 Moisture Condensation When the unit is suddenly moved from a cold to a warm location, or used in a very humid place, moisture from the air can condense on the head-drum. This is called moisture condensation. If the tape is run in this state, it can adhere to the drum. To prevent such a condition from occurring, the unit is provided with a moisture detecting function.
14-5 Regular Checks 14-5-1 Digital Hours Meter The hours meter can display seven items of information, in corresponding display modes, about the operational history of the unit. Use it as a guide in scheduling periodic maintenance.
14-5 Regular Checks 14-5-2 Maintenance Timings Use the following table as a timing guide for checking and replacing components of the unit. These intervals are not guaranteed lifetimes; the timing for replacing components depends on the particular conditions of use. In particular, depending on the degree of dirt contamination and abrasion, pinch rollers and cleaners may require replacement earlier than suggested by this table.
Specifications Tape transport system Tape speed Digital Betacam: 96.7 mm/s MPEG IMX (DVW-M2000/ M2000P): 64.5 mm/s (525/60) 53.8 mm/s (625/50) Betacam SX (DVW-M2000/ M2000P): 59.6 mm/s Analog Betacam (DVW-M2000/ M2000P): 118.6 mm/s (525/60) 101.
Specifications Recommended tapes Digital Betacam cassettes (S, L): BCT-D6/D12/D22/D32/D40 BCT-D34L/D64L/D94L/D124L MPEG IMX cassettes (S, L) (for playback only on DVW-M2000/ M2000P) Betacam SX cassettes (S, L) (for playback only on DVW-M2000/ M2000P) Betacam SP cassettes (S, L) (for playback only on DVW-M2000/ M2000P) Betacam cassettes (S, L) (for playback only on DVW-M2000/ M2000P) Appendix Digital video system Digital video signal system Sampling frequency Y: 13.5 MHz R–Y/B–Y: 6.
MPEG IMX playback (DVW-M2000/M2000P) Video Bandwidth Y DVW-M2000: 0 to 5.75 MHz +0.5 dB/–2 dB DVW-M2000P: 0 to 2.75 MHz +0.5 dB/–2 dB R–Y/B–Y 0 to 2.75 MHz +0.5 dB/–2dB S/N ratio 56 dB or more K factor 1% or less Digital Audio Frequency response (0 dB at 1 kHz) 20 Hz to 20 kHz +0.5 dB/–1.0 dB Dynamic range 95 dB (at 1 kHz, emphasis on) in 4-channel/24-bit mode 90 dB (at 1 kHz, emphasis on) in 8-channel/16-bit mode Distortion (T.H.D at 1 kHz reference level) 0.
Specifications Audio LNG AFM Metal tape Oxide tape Frequency response (at 10 dB below reference level a)) 50 Hz to 15 kHz +1.5 dB/ –2.0 dB 50 Hz to 15 kHz +3.0 dB S/N ratio (at 3% distortion level) 72 dB or more 50 dB or more (Dolby NR off) Distortion (THD at 1 kHz reference level a)) 1% or less 2% or less Wow and flutter 0.1% rms or less Frequency response (at reference level a)) 20 Hz to 20 kHz + 0.5 dB/–2.
Processor adjustment range TIME CODE IN Video level ±3 dB/ –∞ to +3 dB selectable Chroma level ±3 dB/ –∞ to +3 dB selectable Setup level (DVW-M2000/2000) ±30 IRE Black level (DVW-M2000P/2000P) ±210 mV Y/C delay ±100 ns (in analog Betacam playback) Chroma phase ±30° System phase Sync: ±15 µs SC: ±200 ns CUE IN SDI INPUT BNC (1 with active through out) Serial digital (270 Mbits/s) SMPTE 259M/ITU-R BT.656 REF. VIDEO INPUT BNC (2 in loop through connection) Black burst or composite sync 0.
Specifications Remote connectors CONTROL PANEL 10-pin (2), female Front/rear selectable REMOTE 1-IN (9P) D-sub 9-pin, female REMOTE 1-OUT (9P) D-sub 9-pin, female RS-232C D-sub 9-pin, male VIDEO CONTROL D-sub 15-pin, male (for optional BVR-50/50P) REMOTE 2 PARALLEL I/O (50P) 50-pin, female Appendix Memory stick slot Memory stick (8 to 128MB) Accessories supplied PSW 4 × 16 screws for rack mounting (4) Operation Manual (English version ×1, Japanese version ×1) Installation Manual (English version ×1, Japa
Index B Basic menu items 12-5 Betacam Cassette 3-10 compatibility 1-2 SX/SP cassette 3-10 BLACK (function menu) 11-5 C C PHAS (function menu) 11-5 CAPSTN (function menu) 11-7 Capstan override function 4-9 Cassettes 3-10 CD-ROM manual 1-5 CHANNEL CONDITION indicator 2-6 CHARA (function menu) 11-7 CH1 to CH4 buttons 2-11 CHROMA (function menu) 11-5 COMPONENT VIDEO INPUT connectors 2-16 COMPONENT VIDEO OUTPUT connectors 2-16 COMPOSITE VIDEO INPUT connectors/ 75 Ω termination switch 2-16 COMPOSITE VIDEO OUTPU
Index MENU (function menu) 11-3 Menu control buttons 2-6 display 2-8 operation 2-6, 6-2, 12-2 MIXING button 2-4 Moisture condensation 14-4 MONITOR OUTPUT connectors 2-18 MPEG IMX 1-1 cassette 3-10 compatibility 1-2 N Non-drop frame mark 3-9 mode 11-4 O Operation mode 3-9 OPTION connector 2-18 OUTREF (function menu) 11-7 Index P PANEL SELECT switch 2-14 Parts replacement 14-6 PB controls 2-6 PB/EE (function menu) 11-3 PHONES jack/control 2-2 PLAY button 2-11 Playback capstan override 4-9 dynamic motion
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
DVW-M2000/M2000P DVW-2000/2000P (SY, Sony Corporation B & P Company ) 3-826-015-03(1) 2004
