To prevent fire or shock hazard, do not expose the TV to Fain o moisture. This symbol is intended /il\\ o alert the user to the L2 presence of insulated “dangerous voltage” within the product’s enclosure that may full sufficient magnitude constitute a risk of electric shock t persons ‘This symbol is m intended 1o alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Step 1: Connecting the TV You can use an indoor antenna, outdoor antenna, or cable system with your TV. Outdoor antennas or cable TV rems usually provide the best picture quality Connecting an Indoor, Outdoor or Cable Antenna Connect your antenna or able to the T antenna terminal. A barony potent axiomatic cable castle If vou cannot connect your antenna ov cable directly to the TV antenna terminal, follow one of the diagrams below.
Step 2: Using the Remote Control Instructions in this manual are based on using the remote contra. You can also use the controls on the TV, The menu illustrations are from KV-20M20. When features found on either models are discussed, the manual lists the medals covered by that specific set of mends Koch + The menu disappears 90 seconds after vou press a button, or immediately after vou press MEN « Refer to separate instructions far remote control per-programming {RV-20V only .
' ep 3: Setting up Your Channels Setting Cable TV On or Off If you have connected the TV to a cable TV system, set CABLE fo ON. I not, set CABLE to OFF. 1 Press MENU. 2 Move the cursor to SET UP and press RETURN. 3 Move the cursor to CABLE and €T UF [ press RETURN. 8070 PRO BRAN CRAVENNESS, ERASE /80D Cruel BLOCK CHANNEL 6108 SHEEN e 0L Press select ON or OFF. Press RETURN. & Press MENU to return to the TV program.
Erasing or Adding Channels After you run AUTO PROGRAM, you can erase unnecessary channels or add new ones 1 Press MENU. 2 Press select SET UP and press RETURN, 3 Press select CHANNEL ERASE/ADD and press RETURN. CHANNEL 5030E SHE NU Use ¥ { VESTRY Exit ) . Creon 4 Yo erase or add a channel: runnel o (1) Press select the channel you want to erase or add. (2) Press select ERAS] or ADD. Use (B9 ar (Cues o set act e carrel tse ¥ § G Exi L 65 (3} Press RETURN.
Watching the TV Press POWER to turn the TV on. Note 1 VIDEO appears on the screen, press EVIDENT o that a channel ambient apparatus Selecting a Channel Directly A o, Press (-9 to select a channel, @ The channel will change after @ 2 seconds, or you can press ENTER for immediate select 0 Scanning Through Channels Press CH until the channel you cH want appears. Umping Quickly Between Two Channels Press JUMP. J Ump The TV switches from the current channel to the previous channel that you watched.
Displaying On-Screen Information Else the DISPLAY key to check the T 1 Press DISPLAY, DISPLAY The channel number will be displaced, The TV will alas display the MTS duodenum if SAF, MAIN MONO are selected (RV20621, 20830, 20Ve0, 21R%29, 2IRG20C, AIRSHOW, 215107 only The MTS mode display disappears after 4 seconds 2 Press DISPLAY again. XIS ON will appear on the serene.
Using the VIDEO Menu Adjusting the Video Settings You can adjust the picture, hue, color, brightness, and sharpness of any TV image. 1 Press MENU. Move the cursor () to VIDEO and press RETURN. 3 Press select the feature that you want to adjust a 2 and press RETURN. RIGHTNESS Il See the Adjustable stems chart for a & SEVERENESS fifth list of the adjustments you can make.
Additional Features Selecting Stereo or Bilingual Programs (MTS) KC-20520, 20521, 20530, 20V60, 21PS1, 21R520, 21RS20C, 21RS36C, 215D1 only. Menus shown are for KC-20520, The Multichannel TV Sound (MTS) feature allows vou to enjoy stereo sound (MAIN, Second Audio Programs (SAP), or monaural sound (MONO when available 1 Press MENU. Move the cursor to AUDIO and press RETURN. Move the cursor to MTS and press RETURN. Press select MAIN, SAP, or MONO. a i S Press MENU to return to the TV program.
5 Move the cursor to FIXED or VARIABLE and press RETURN. Your selection will turn yellow. 6 Press MENU ta return to the TV program. Choose To FIXED Adjust the volume with your stereo. VARIABLE Adjust the volume through the TV, Note + St the volume on v stereo low when switching from VAR to FINED to avoid overloading boar external speakers. Turning on Surround Sound KV-20V60 only Use this feature to listen to TV audio in Surround Sound mode. 1 Press MENU. 2 Move the cursor to AUDIO and press RETURN.
4 Move the cursor to 1.or 2 and press THRONE BLOCK RETURN. >l pressies select the channel Tonne L BLOCK that you want to block. Press 1 RETURN. 6 Repeat steps 4 and 5 to enter the second channel that you want to block, 7 Press MENU to return to the TV program. If you switch to the blocked channel, BLOCKED appears. The screen is black and the sound is muted. To cancel a CHANNEL BLOCK setting 1 Follow steps 1-4 above. 2 Press RESET.
4 Press RETURN again to move the cursor to the number pad. 5 Press A+ or V-to select a number on the CHANNEL GUIDE (the button number will turn red) and press RETURN. The tarns red. Buttons 0-9, DISPLAY (D) and ENTER (E) are available for CHANNEL GUIDE access 6 Press select the channel that you want to assign to that button, and press RETURN.
troubleshooting If you are having a problem with your TV, try the suggestions below. If the problem persists, contact your neared! Sony dealer, Problem Suggestion No picture, no sand o Make sure the power cord i connected Check the TV/VIDEO dotting: when watching TV, set to TV; when watching video @pes to VIDEO {page 9). Try another channel. It could be station froufrou Poor or no picture, + Adjust PICTURE in the VIDEO menu (page 10) good sound * Adjust BRIGHTNESS in the VICED men {pane 10).
SONY KV-20V60 Using the Pr-Programmed Remote Commander With the supplied Remote Commander, you can operate a Sony video cassette recorder {Beta, B mm, VHS) or a video disc player as well a3 mast non-Sen video equipment contradicted to your TV by following the steps below. 1 While pressing CODE SET, pass 0-9 %o enter the manufacturer’s date number, For example, to operate a Sony 8 mm VCR, press 0, 2 and ENTER. oo even Use the video operating buttons on the Remote Commander to operate the video equipment.