PCG-FXA32/FXA33/FXA35/D/FXA36 SERVICE MANUAL For American Area US Model Canadian Model Ver 4-2002D Revision History S400 Lineup : PCG-FXA32 PCG-FXA33 PCG-FXA35/D PCG-FXA36 l a i t n e d i f Illust : PCG-FXA36 n o C NOTEBOOK COMPUTER 9-874-453-04
Information in this document is subject to change without notice. Caution Markings for Lithium/Ion Battery - The following or similar texts shall be provided on battery pack of equipment or in both the Sony and VAIO are trademarks of Sony. Intel logo and Intel Inside logo are registered trademarks of Intel Corporation. Pentium MMX operating and the service instructions. is a trademark of Intel Corporation.
TABLE OF CONTENTS Section Title Page CHAPTER 1. REMOVAL 1-1. 1-2. 1-3. 1. 2. Section Title Page CHAPTER 2. SELF DIAGNOSTICS ...................... 2-1 Flowchart ......................................................................... 1-1 Main Electrical Parts Location Diagram ......................... 1-1 Removal ........................................................................... 1-2 Assy Hood Keyboard, Keyboard Unit .............................
CHAPTER 1. REMOVAL 1-1.
1-3.Removal 1. Assy Hood Keyboard, Keyboard Unit 3Screw M2X4 Special Head (Black) 4Pull it up sliding it to the right. 8Screw M2X4 Special Head (Black) 6Assy Hood Keyboard q;Keyboard Unit 7 5 Four Claws 1 9 2 MBX-61 Board CON21 MBX-61 Board CON15 2.
3. Combination Drive, DVD-ROM Drive 1. FXA33/FXA35/D/FXA36 Model 6Bracket CD-ROM R 4+B M2 (X2) (Gold) 5+B M2 (X2) (Gold) 0COMBO Drive 7Spring Drive (PA-R) 8Screw (M1.7X3.5) (X3) (Black) Claw 9Assy Door DVD-RW (PA) 1+B M2 (X2) (Gold) 3Spring Drive (PA) 2Bracket (CD-ROM L) 2. FXA32 Model 3+B M2 (X2) (Silver) 5Bracket CD-ROM R 4+B M2 (X2) (Silver) 8DVD-ROM Drive 6Tapping screw (B1.
4. HDD, Door Battery 1Screw M2X6 Special Head (X6) (Gold) 1Screw M3X4 (X2) (Gold) 3 3Bracket HDD 6Spacer (Keyboard) 2FPC 50Pin (for HDD) MBX-61 Board CON9 5HDD 4FPC 50Pin (for HDD) 2Screw M3X4 (X2) (Gold) 4Door Battery 5. Assy Palmrest, Pad Touch, CNX-129 Board, Plate Palmrest, Bracket Pad 3Pull it to the front slightly and raise to remove it.
6. Display Assy, Cover Hinge 1Stand the LCD upright to the MBX-61 board. 7Screw M2.6 Cross (Hole) Bind (Black) 3+B M2 (X2) (Gold) 9Screw M2X6 Special Head (X2) (Gold) q;Screw +B 2X12 (Silver) 4Plate ground (SH) qaScrew M2X6 Special Head (Gold) 2 qs 5Screw M2.6 Cross (Hole) Bind (Black) Six Claws MBX-61 Board CON4 6Screw M2.6 Cross (Hole) Bind (X2) (Black) 8Screw (M2), 0 Number P3 Kind (Black) qdClose simultaneously both left and right hinges approximately 90° in the direction of the arrow.
7. Cooling Unit-2 1Rotate the three screws that are built together with the Cooling Unit-2. Shield Sheet (Fan) Shield Tape (Fan) 2 4Cooling Unit-2 2 3 MBX-61 Board CON14 8.
9.
10. Speaker Unit, SWX-74 Board 6Screw M2X4 (X2) (Black) Note : When removing the speaker unit, be sure not to damage the hood keyboard. 4Screw M2X4 (X5) (Black) SWX-74 Board JP2 SWX-74 Board JP3 7Speaker Unit 3 5SWX-74 Board SWX-74 Board JP1 8Screw M2X4 (X2) (Black) 1 2 9Speaker Unit Note : To re-install it, align the notch of the speaker unit with the projection of the hood keyboard. Notch Speaker Unit Notch Projection Hood Keyboard Projection Hood Keyboard 11.
. Card Modem (Removing from the bottom) 1Screw M2X4 Special Head (Black) 2Door Modem 3Grip M2 (X2) (Black) 4Card Modem 5 Confidential 1-9 PCG-FXA32/FXA33/FXA35/D/FXA36 (AM)
. LCD Section – Made by HI – 1. Assy Housing Bezel, LCD unit (15 inch) 1Cover Screw Side (15) (X3) 3Cover Screw Shaft 4+P 2.6X6 Lock Precision b Type3 (Black) 2Screw M2X3 Special Head (X3) (Gold) Assy Housing Bezel 15H-Z a : claw part 7 3Cover Screw Shaft 2Screw M2X3 Special Head (X3) (Gold) 1Cover Screw Side (15) (X3) c b 4+P 2.
2.
1-4.Replacing the CPU 1. Removing the CPU 1 2 1 Insert a screwdriver tip into the groove as shown and slant it in the direction of the arrow. NOTE: Do not use screwdrivers having a large tip than the width of the groove. Otherwise, it may cause the groove to be damaged. 2 The CPU can be removed upward. The base under the CPU moves slightly in the direction of the arrow and the lock is released. 2. Installing the CPU Attach the CPU while aligning the cut-out with this position.
1-5. Replacing Various Connectors on the MBX-61 Board Replace the connectors of “5-3. Connector Section” as follows. 1. Removing the Bracket I/O When removing the connectors of reference numbers 901, 902 and 903 (refer to page 5-7), remove the bracket I/O first. Shield Tape (USB) 2J +B 2X4 (X2) (Silver) Bracket I/O Screw (HEX) (X6) (Silver) MBX-61 Board 2.
1-6. DIP Switch Setting of the MBX-61 Board Set the DIP switch on the MBX-61 board (main board) to match with the LCD that is used in this computer. Part No. of LCD DIP switch setting ON 1 2 3 4 1-476-186-12 The upper position where ON indication is shown is the ON position . The lower position is the OFF position. No. ON/OFF 1 2 3 4 0 1 0 0 0 : ON 1: OFF ON 1 2 3 4 A-8025-245-A The upper position where ON indication is shown is the ON position . The lower position is the OFF position. No.
CHAPTER 2. SELF DIAGNOSTICS ATTENTION Please confirm “Self Diagnostics” method which will be informed you with distribution of “Self Diagnostics” software.
CHAPTER 3. BLOCK DIAGRAM CPU PCG-FX Series AMD Mobile Duron/Athlon 900/1000MHz BLOCK DIAGRAM Rev.A (Cache:128KB L1 64/256KB L2) (FSB 200 MHz) w/ Port Replicator (PCGA-PRFX1) LCD Panel XGA ADDRESS DATA (Max.
CHAPTER 4.
CHAPTER 5. EXPLODED VIEWS AND PARTS LIST NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “ * ” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • When two or more parts are shown in parallel, use the part described first as the main part. • The indication [CH] is used for identification of part type.
5-1. Main Section Ref.No. 1 3 *8 * 11 15 Part No. X-4623-848-1 4-640-837-22 4-651-706-01 4-656-752-01 4-643-832-21 Description [CH]...ASSY BOTTOM (Q) DOOR BATTERY HEATSINK BOTTOM [CH]...INSULATOR HEATSINK BOTTOM DUMMY CARD 18 19 20 22 24 A-8049-276-A X-4623-389-1 1-529-287-11 1-790-639-22 1-796-230-11 COMPLETE PWB SWX-74 ASSY HOOD KEYBOARD Z (P) SPEAKER UNIT FPC 50PIN (FOR HDD) (FXA35/D/FXA36)...
B8 B1 B33 B33 J 187 181 185 186 B1 I B1 B1 22 J 30 B32 B15 N A N 25 K B1 B15 M 60 19 188 B1 B8 24 164 Supplied with 19 (FXA35/D/FXA36 Model only) 180 15 B1 182 124 76 136 I 72 K 31 28 B37 29 123 34 20 B4 B8 B10 H Supplied with 88 B4 B8 B10 125 18 Supplied with 88 M (FXA32 Model) B1 166 B8 88 26 20 15 63 27 B14 136 81 147 B17 C 194 H 76 149 B8 32 B10 162 33 B4 148 B8 157 F 46 L B7 L C 2 [COR] B1 71 B10 78 D 154 193 161 B12
MEMO 5-1-A. FDD Section How to use properly the FDD repair parts. Types of service to be provided are different depending on the serial No. of the FDD in use. Label FD X-XXX-XXX-XX Serial No. The service types are shown below depending on the serial No. that is printed in the bottom right of the FD label. [Serial No. : 4-656-805-0*] [Serial No. : 4-641-763-3*] 800 800 806 807 804 801 805 802 B1 803 B1 Ref.No. Part No. Description 800 A-8025-674-A FDD UNIT ASSY (TN-CH) Ref.No.
5-2. LCD Section (FXA32/FXA33/FXA36 Model) – Made by HI – 426 424 434 B30 403 B22 435 406 434 408 B22 424 407 Ref.No. 401 402 403 406 407 Part No. 1-476-318-21 X-4623-380-1 X-4623-419-2 4-637-902-31 1-476-186-12 Description INVERTER UNIT HINGE LEFT 15 ASSY HOU,BEZEL 15H-Z LATCH LCD-UNIT (HI 15 TFT XGA) 408 412 413 414 414 4-637-903-01 X-4623-416-1 4-642-762-31 4-658-354-11 4-658-354-21 SPRING LATCH ASSY HOU, DISPLAY 15H-Z COVER HINGE (15) (FXA36)...LABEL ID (U) (FXA33)...
5-2-A. LCD Section (FXA35/D Model) – Made by HI – 303 Ref.No. 301 302 303 304 305 Part No.
5-3. Connector Section Ref.No. 901 Fig. Part No. Description 1-779-745-21 JACK, DC DC IN connector 902 9-885-018-97 CONNECTOR (1.2MM), USB USB connector Bracket I/O 903 902 901 9-885-018-98 CONNECTOR (1.6MM), USB USB connector ∗ Among the parts that are used on the boards of this model, only the connectors that are show in the list can be replaced. (The parts other that the specified connectors cannot be replaced.
Revision History Suffix Ver. Date -01 Ver. 1 2001.10.03 -02 Ver.2 2002.01.07 Contents QM No. First Edition Front Page (Model Line Up), Page 1-3, Page 1-14, Page 4-1, Page 5-2, Page 5-3 M2002_001K Page 5-4, Page 5-6(a), Page 5-6(b), Back Cover -03 Ver.3 2002.03.20 Page 5-3 N2002_020K -04 Ver.4 2002.03.26 Page 5-2, Page 5-4(a) Page 5-4(b) N2002_040K < Remarks > 2001.12.