LX40/LX50/LX60S/LX70S RMT-V293A/V294A SERVICE MANUAL Chilean Model SLV-LX50CL/LX50CS/LX70SCL/ LX70SCS Mexican Model SLV-LX40MX/LX50MX/LX60SMX/ LX70SMX 1 4 7 2 3 5 6 8 9 Panama Model Venezuelan Model 0 SLV-LX50PA/LX50PC/LX50VZ/ LX70SPA/LX70SPC/LX70SVZ g S MECHANISM SLV-LX70S Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENT for MECHANICAL ADJUSTMENTS.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. 2. 3. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair.
Section SERVICE NOTE Title TABLE OF CONTENTS Page Section 1. ERROR CODE INDICATION ........................................... 5 1 GENERAL Getting Started ........................................................................... 1-1 Step 2 : Setting up the remote commander ............................. 1-1 Step 3 : Hookups ..................................................................... 1-1 Selecting a language ...............................................................
SERVICE NOTE 1. ERROR CODE INDICATION • Error codes are indicated using the lower 5 digits in the fluorescent display tube. “At this time, Colon “:” between character is not indicated.” Mode code indication when the error has occurred.
SLV-LX40/LX50/LX60S/LX70S This section is a translated version of Instruction Manual SLV-LX70S model Part number: 3-065-284-12 SECTION 1 GENERAL Controlling other TVs with the remote commander (SLV-LX70S and LX60S only) Step 2 : Setting up the remote commander The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number. Inserting the batteries 1 Set •TV / VIDEO at the top of the remote commander to •TV.
For SLV-LX50 and LX40 Hookup 1 A Use this hookup if your TV has stereo jacks Antenna hookup VCR Make the following connections if you’re using an antenna (if you don’t have cable TV).
3 The SINTONIZADOR menu appears. Set ANTENA/CABLE to CABLE and press OK. For details, see page 26. Hookup 2 : VCR setup Before you start… • Turn on the VCR and the TV. AJUSTE SINTONIZADOR ANT CABLE ANTENA / CABLE • Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window. SELECCIONAR SIGUIENTE CANCELAR the RF UNIT switch to CH3 1 Set or CH4, whichever channel is not used in your area. If both are used, set the switch to either channel. For details, see page 67.
3 The SINTONIZADOR menu appears. Set ANTENA/CABLE to ANT and press OK. For details, see page 26. AJUSTE SINTONIZADOR Selecting a language ANT CABLE ANTENA / CABLE You can change the on-screen display language. SELECCIONAR SIGUIENTE CANCELAR : : OK : EASY SET UP 4 The AJUSTE AUTO. starts. AJUSTE SINTONIZADOR MENU Before you start… • Turn on the VCR and the TV. • Set the TV to the VCR channel (channel 3 or 4). If your TV is connected to the VCR using A/V connections, set the TV to video input.
If the clock does not activate Press M/m to highlight NO for TOTAL. AUTO. and press OK. 2 PLAY OK AJUSTE AUTOMATICO RELOJ TOTAL. AUTO. NO CH AJUSTE RELOJ HORARIO VERANO ––– AUTO VOLVER SELECCIONAR AJUSTAR PARA SALIR 1 2 Press M/m to highlight the item you want to set and press OK. Then press M/m to make the setting and press OK.
Press M/m to highlight ANTENA/CABLE, then press OK. 3 Presetting channels PLAY This VCR is capable of receiving VHF channels 2 to 13, UHF channels 14 to 69 and unscrambled CATV channels 1 to 125. First, we recommend that you preset the receivable channels in your area using automatic presetting methods. Then, if there are any unwanted channels, disable them manually. If you have already decided which channels you wish to preset, set them directly using manual presetting methods.
Press M/m to highlight PREAJUSTE DEL SINTONIZADOR, then press OK. 2 PLAY If the picture is not clear PREAJUSTE DEL SINTONIZADOR CH ANTENA / CABLE AJUSTE AUTO. OK MANUAL AFT SINTONIA FINA VOLVER SELECCIONAR AJUSTAR PARA SALIR 3 1 2 3 4 5 6 7 8 9 0 • To preset a channel: 1 Press the number buttons to enter the channel number, then press ENTER. 2 Press OK. 3 Press M/m to set MANUAL to +, then press OK. PLAY • To disable a channel: 1 Press CH +/– to select the channel number. 2 Press OK.
Turning on the VCR and TV, and starting playback automatically (Trinitron TV Synchro Play) Press H PLAY. 3 PLAY When the tape reaches the end, it will rewind automatically. You can only use this function if your TV is made by Sony (Trinitron TV). OK How to connect to use this function Connect the VCR and TV with the audio/video cable (see “Audio/video (A/V) hookup” on pages 8 and 9). Be sure to connect the audio/video cable to the VIDEO IN 1 jacks on the TV if the TV has two inputs or more.
To watch another TV program while recording Recording TV programs using the Dial Timer 1 Press TV/VIDEO to turn off the VIDEO indicator in the display window. the TV is connected to the VCR’s LINE OUT jacks, set the TV to the TV’s 2 Ifantenna input; if not, skip this step. Select another channel on the TV. 3 To save a recording To prevent accidental erasure, break off the safety tab as illustrated. To record on the tape again, cover the tab hole with adhesive tape.
To use the VCR after setting the timer Notes • If eight programs have already been set using the PROG./VERIF. menu, “LLENO” appears in the display window for about five seconds. • If you set the clock using the Auto Clock Set function, the clock will adjust itself to the incoming time signal regardless of adjustments made with the Dial Timer. Be sure you have set ACS correctly. To use the VCR before a timer recording begins, just press ?/1.
To use the VCR after setting the timer Locking the VCR (Child Lock) To use the VCR before timer recording begins, just press ?/1. The indicator disappears from the display window and the VCR switches on. Remember to press ?/1 to reset the VCR to the timer recording standby mode after using the VCR. After you have set the timer, you can lock all of the buttons on the VCR so that the settings are not canceled by mistake.
Setting the recording duration time Checking/changing/canceling timer settings After you have started recording, you can have the VCR stop recording automatically after a specified duration. Before you start… • Turn on your TV and set it to the video channel. z REC ?/1 TIMER 1 2 3 4 5 6 7 8 9 0 1 While recording, press z REC. The indicator appears in the display window. VIDEO APC SP CLEAR MENU z REC repeatedly to set the duration time.
How sound is recorded on a video tape Searching for the beginning of a timer recorded program The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with the picture. Monaural sound is recorded onto the normal audio track along the edge of the tape. Monaural sound If you record a program using the timer function, you can easily find the beginning of the recording with this SEARCH MODE function.
Searching using the index function Searching using the Time Search function The VCR marks the tape with an index signal at the point where each recording begins. Use these signals as references to find a specific recording. The VCR can search up to 9 index signals ahead of or behind the current position. You can easily find a specific point on a tape by using the Time Search function.
To cancel searching Press H PLAY or x STOP. Adjusting the picture To turn off the bar indication Press DISPLAY again. Adjusting the tracking Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window, then turns off), distortion may occur if the recording is in poor condition. In this case, manually adjust the tracking. Notes • The figure on the bar indication represents the total time length of the inserted tape as shown below.
PÁGINA2 Editing with another VCR Menu option Set this option to APC • SI to switch on the APC (Adaptive Picture Control) function and improve picture quality. • NO to switch off APC. REALITY REGENERATOR • SI to switch on the Reality Regenerator (Reality Regenerator) function and restore the picture to its original quality during playback. • NO to switch off Reality Regenerator.
Additional Information Attaching the external antenna connector General setup information When using a 300-ohm twin lead cable for a VHF/UHF antenna, use the EAC-32 antenna connector (not supplied) to connect the antenna to the VCR. Setting the RF unit When connecting the VCR to the TV using only the antenna cable, you must set the RF UNIT switch on the rear of the VCR so that the TV can receive the correct signal from the VCR.
SLV-LX50 and LX40 Display window STEREO VIDEO APC SAP LP SP EP RR A ?/1 POWER switch (44) I x STOP button (33) (66) A Timer indicator (40) (44) G RR (Reality Regenerator) indicator (60) B Z EJECT button (33) J X PAUSE button (33) (66) H Tracking indicator (60) C Tape compartment K DIAL TIMER (38) (54) (55) (56) B SAP (Second Audio Program) indicator (52) (SLV-LX70S and LX60S only) D Remote sensor (5) L SEARCH MODE button (54) (55) (56) C STEREO indicator (52) (SLV-LX70S and LX60S only) E m
K ?/1 (power) switch (6) (44) L TV/VIDEO button (6) (37) M AUDIO MONITOR button (52) (SLV-LX70S and LX60S only) N TIMER button (43) (50) O Number buttons (31) P ENTER button (31) 1 2 3 4 5 6 7 8 9 0 Q CH (channel) +/– buttons (6) (36) R CLEAR button (33) (51) S y SLOW button (47) T ×2 button (47) U REPLAY button (33) 78 Index to parts and controls 1-19E 1-19
SLV-LX40/LX50/LX60S/LX70S SECTION 2 DISASSEMBLY NOTE: Follow the disassembly procedure in the numerical order given. 2-1. CASE, FRONT PANEL BLOCK ASSEMBLY 1 Two tapping screws 3 Upper case 4 Flat Cable FFJ-4 2 Two tapping screws Hooks 5 Flat Cable FDM-10 Hooks Hooks Hooks 6 Front panel (Engaged by the six hooks) 2-2. DI-80 BOARD, FJ-32 BOARD 5 FJ-32 board 6 Flat Cable FFJ-4 4 Two screws (B2.6 x 8) 1 Two screws (B2.
2-3. REAR PANEL 2 Rear panel (Engaged by the seven hooks) Hooks Hooks Hooks Hooks 1 POWER code stopper 2-4.
2-5.
2-6.
2-7.
SLV-LX40/LX50/LX60S/LX70S SECTION 3 BLOCK DIAGRAMS 3-1.
SLV-LX40/LX50/LX60S/LX70S 3-2.
SLV-LX40/LX50/LX60S/LX70S 3-3.
SLV-LX40/LX50/LX60S/LX70S 3-4.
SLV-LX40/LX50/LX60S/LX70S 3-5.
SLV-LX40/LX50/LX60S/LX70S 3-6.
SLV-LX40/LX50/LX60S/LX70S SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) (For printed wiring boards) : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.) • Through hole is omitted. • Circled numbers refer to waveforms. • There are few cases that the part printed on diagram isn’t mounted in this model. • Chip parts.
SLV-LX40/LX50/LX60S/LX70S 4-1.
SLV-LX40/LX50/LX60S/LX70S MA-405 (VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER) PRINTED WIRING BOARD — Ref. No.
SLV-LX40/LX50/LX60S/LX70S MA-405 (REC/PB HEAD AMP) SCHEMATIC DIAGRAM – Ref. No: MA-405 board; 1000 series – • See page 4-21 for waveforms. 1 2 3 MA-405 BOARD(1/7) REC/PB HEAD AMP(RP BLOCK) A XX MARK:NO MOUNT 4 5 6 7 8 9 10 11 12 NO MARK:REC/PB MODE R :REC MODE P :PB MODE 13 CN270 4P JL271 5 JL272 4 JL273 C285 0.01u JL274 IC260 B+ 3 D AUDIO CH1 H AUDIO REC 2 1 AUDIO CH2 L 3 2 1 JL266 R270 470 JL270 AUDIO CH1 C271 0.01u B C272 0.1u B 12 H.SYNC 11 AGC DET 13 R2.
SLV-LX40/LX50/LX60S/LX70S MA-405 (Y/C, AUDIO PROCESSOR) SCHEMATIC DIAGRAM – Ref. No: MA-405 board; 1000 series – • See page 4-5 for printed wiring board. • See page 4-21 for waveforms. 2 3 MA-405 BOARD(2/7) Y/C, AUDIO PROCESSOR (VA BLOCK) 6 7 8 9 10 B+ C242 0.01u B 58 INV AMP P 84 OSD V OUT C204 C205 1u 0.01u B B C202 0.01u B 3.7 1.3 R203 330 Q201 2SC2712Y-TE85L BUFFER D7 D8 R204 8200 R210 1500 C5 H C574 10u 16V 1.8 R206 XX 5.
SLV-LX40/LX50/LX60S/LX70S MA-405 (SERVO/SYSTEM CONTROL) SCHEMATIC DIAGRAM – Ref. No: MA-405 board; 1000 series – • See page 4-5 for printed wiring board. • See page 4-21 for waveforms.
SLV-LX40/LX50/LX60S/LX70S MA-405 (AUDIO PROCESS) SCHEMATIC DIAGRAM – Ref. No: MA-405 board; 1000 series – • See page 4-5 for printed wiring board. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 MA-405 BOARD(4/7) AUDIO PROCESS (AU BLOCK) A XX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE LX60S/LX70S JL331 14 SIF MA-405 (6/7) (SEE PAGE 4-17) AN_GND JS302 B JL325 JL326 JL327 SW_5V B+ XX B+ 2.5 2.5 0.4-0.7 HF_GND 1.7 GND R N.C. VCC5V REC ADJ 5.
SLV-LX40/LX50/LX60S/LX70S MA-405 (TUNER) SCHEMATIC DIAGRAM – Ref. No: MA-405 board; 1000 series – • See page 4-5 for printed wiring board.
SLV-LX40/LX50/LX60S/LX70S MA-405 (DISPLAY CONTROL) SCHEMATIC DIAGRAM – Ref. No: MA-405 board; 1000 series – • See page 4-5 for printed wiring board.
SLV-LX40/LX50/LX60S/LX70S MA-405 (POWER SUPPLY) SCHEMATIC DIAGRAM – Ref. No: MA-405 board; 1000 series – • See page 4-5 for printed wiring board. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 MA-405 BOARD(7/7) POWER SUPPLY (PS BLOCK) XX MARK:NO MOUNT NO MARK:REC/PB MODE B L660 68uH JL618 13.5 SW_5V JS606 ET601 C601 0.
SLV-LX40/LX50/LX60S/LX70S MA-405 BOARD (1/7) (R/P BLOCK) MA-405 BOARD (2/7) MA-405 BOARD (3/7) (VA BLOCK) (SS BLOCK) 7 IC201 2 REC 1 IC260 4 REC/PB qf IC201 yj REC/PB qj IC160 el 4fsc (OUT) REC/PB wd IC160 i;T REEL 4.8Vp-p V 3.6Vp-p 2 IC260 5 REC/PB H 8 IC201 7 REC 0.1µsec/div 0.1V/div 3.5Vp-p H 3 IC260 7 PB 0.1µsec/div 50mV/div 360mVp-p H 0.5Vp-p 5.0Vp-p OSC OUT REC/PB 25.3MHz 69.9kHz 4.6Vp-p ql IC160 t; OSC V IN REC wg IC160 il DRUM FG REC/PB 50Vp-p 2.
FJ-32 (LINE 2 IN) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM — Ref. No. FJ-32 Board: 1,000 Series — There are few cases that the part printed on this diagram isn’t mounted in this model. FJ-32 BOARD 1 2 3 4 5 6 7 FJ-32 BOARD LINE 2 IN A •REF.NO.: 1,000 SERIESR801 0 LX40/LX50 CN801 9P JL801 L2_VIDEO 9 JS801 XX JL802 8 L2(L) 7 AU_GND 6 L2(R) 5 AU_GND 4 EJECT 3 POWER 2 D GND 1 C803 0.001u R802 0 JL803 JL804 C805 0.001u LX60S/LX70S JL805 C806 0.
DI-80 (DIAL TIMER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM — Ref. No. DI-80 Board:1,000 Series — There are few cases that the part printed on this diagram isn’t mounted in this model. DI-80 BOARD 1 2 3 4 5 6 7 DI-80 BOARD DIAL TIMER A •REF.NO.
SLV-LX40/LX50/LX60S/LX70S SECTION 5 INTERFACE, IC PIN FUNCTION DESCRIPTION 5-1.
5-3. SYSTEM CONTROL — SYSTEM CONTROL PERIPHERAL CIRCUIT INTERFACE (MA-405 BOARD IC160) Signal RESET I2C DATA 1 I2C CLOCK 1 I2C DATA VIDEO I2C CLOCK VIDEO (ARC) S OUT 1 (ARC) CLK 1 Pin No. MA-405 Board IC160 ef MA-405 Board IC160 es MA-405 Board IC160 ea MA-405 Board IC160 us MA-405 Board IC160 ua MA-405 Board IC160 rs MA-405 Board IC160 ra I/O I I/O level Normally “H”, “L” when service interruption detected or restored. I/O Serial communication data to EEPROM I2C161.
5-7. SERVO/SYSTEM CONTROL MICROPROCESSOR PIN FUNCTIONS (MA-405 BOARD IC160) Pin No.
Pin No.
SLV-LX40/LX50/LX60S/LX70S SECTION 6 ADJUSTMENTS 6-1 MECHANICAL ADJUSTMENTS For the mechanical adjustments, please refer to the “VHS MECHANICAL ADJUSTMENT MANUAL (S MECHANISM)” (9-921-647-11). 6-2. ELECTRICAL ADJUSTMENTS See the adjusting part location diagram from on page 6-6 for the adjustment. 2-1. 2-1-3. Set-up of Adjustment In this adjustment, NTSC pattern generator is connected with LINE input terminal. When check to tuner, connected AERIAL terminal.
2-1-5. Input/Output Levels and Impedance Video input: LINE IN Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative Video output: LINE OUT Output signal: 1 Vp-p, 75 ohms, unbalanced, sync negative Audio input: LINE IN Input level: –7.5 dBs (0 dBs= 0.775 Vrms) Input impedance: more than 47 kilohms Audio output:LINE OUT Standard level: –7.5 dBs at load impedance 47 kilohms Output impedance: less than 10 kilohms 2-2. POWER SUPPLY CHECK 2-2-1.
2-3. SERVO SYSTEM CHECK 2-3-1. RF Switching Position Adjustment (MA-405 Board) [Adjustment Purpose] To adjust the link of the A-ch and B-ch of the tape playback outputs. To make the unit compatible with other tapes and units. If this specification is not satisfied, the link will appear on the screen and the screen will be disrupted, etc. 2-4. AUDIO SYSTEM ADJUSTMENT • Adjust both L ch and R ch.
2-4-2. HiFi Switching Position Adjustment (MA-405 Board) [Adjustment Purpose] To adjust the link of the A-ch and B-ch of the tape playback outputs. To make the unit compatible with other tapes and units. If this specification is not satisfied, the link will appear on the screen and the screen will be disrupted, etc.
2-5.
SLV-LX40/LX50/LX60S/LX70S SECTION 7 REPAIR PARTS LIST 7-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. The components identified by mark ! or dotted line with mark ! are critical for safety.
7-1-2. CHASSIS SECTION 54 55 #1 #1 #1 54 54 54 54 53 56 52 51 54 not supplied not supplied not supplied Ref. No. 51 52 53 * 53 * 53 Part No. Description 3-959-383-01 BASE (R), MD 3-987-076-11 PANEL, REAR A-6713-826-A MA-405 COMPLETE PC BOARD (LX50:CL,CS) A-6713-827-A MA-405 COMPLETE PC BOARD (LX60S/LX70S:MX,PA,PC,VZ) A-6713-828-A MA-405 COMPLETE PC BOARD (LX70S:CL,CS) Remarks Ref. No. Part No.
7-1-3. MECHANISM DECK SECTION-1 707 #2 708 712 711 709 706 723 704 710 705 702 713 720 722 725 703 701 724 701 721 714 716 719 715 717 718 Ref. No. Part No.
7-1-4. MECHANISM DECK SECTION-2 767 770 768 769 761 758 #2 764 762 763 759 760 762 757 763 #3 766 756 765 755 754 752 753 751 Ref. No. Part No. Description 751 752 753 754 755 X-3947-581-4 3-977-462-01 X-3947-573-1 X-3947-580-5 3-977-513-02 BRAKE ASSY,MAIN(T) SPRING,EXTENTION. (MAIN BRAKE) ARM ASSY, PENDULUM BRAKE ASSY, MAIN(S) LEVER, REC PROOF 756 757 758 759 760 3-976-767-01 3-977-487-01 X-3947-587-1 X-3947-589-1 3-977-488-01 SPRING, TENS. (REC.
7-1-5. MECHANISM DECK SECTION-3 816 815 817 M902 803 818 803 814 #2 812 813 828 811 829 810 808 809 819 820 827 821 826 807 805 822 804 806 823 824 832 831 830 M903 803 801 825 802 833 #4 Ref. No. Part No.
MA-405 Ref. No. 7-2. Part No. Description ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • CAPACITORS: uF: µF Ref. No. Part No.
MA-405 Ref. No. Part No. Description Remarks C143 C144 C145 1-126-965-11 ELECT 1-126-965-11 ELECT 1-126-935-11 ELECT 22µF 22µF 470µF 20% 20% 20% 50V 50V 10V C146 C160 C161 C162 C163 1-164-161-11 1-163-809-11 1-163-809-11 1-163-038-00 1-163-809-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0022µF 0.047µF 0.047µF 0.1µF 0.
MA-405 Ref. No. Part No. Description Remarks C323 C324 1-126-163-11 ELECT 1-109-978-81 ELECT 4.7µF 10µF 20% 10% 50V 16V C325 C326 C327 C328 C329 1-126-163-11 1-124-242-00 1-126-160-11 1-126-157-11 1-126-157-11 ELECT ELECT ELECT ELECT ELECT 4.7µF 33µF 1µF 10µF 10µF 20% 20% 20% 20% 20% 50V 25V 50V 16V 16V C330 C331 C332 C333 C334 1-163-023-00 1-124-242-00 1-124-589-11 1-164-004-11 1-164-489-11 CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP 0.015µF 33µF 47µF 0.1µF 0.
MA-405 Ref. No. Part No. Description C666 C669 C671 C672 C701 1-124-589-11 1-164-232-11 1-126-965-11 1-164-159-21 1-104-664-11 ELECT CERAMIC CHIP ELECT CERAMIC ELECT 47µF 0.01µF 22µF 0.1µF 47µF 20% 10% 20% 20% 16V 50V 50V 50V 25V Remarks C702 C704 C706 C707 C709 1-164-232-11 1-126-163-11 1-164-232-11 1-164-161-11 1-126-933-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT 0.01µF 4.7µF 0.01µF 0.
MA-405 Ref. No. Part No. Description JR007 JR008 JR009 JR010 JR011 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 Remarks Ref. No.
MA-405 Ref. No. Part No. Description Remarks TRANSISTOR PT380F3 TRANSISTOR PT380F3 TRANSISTOR 2SC1815GR-TPE2 TRANSISTOR 2SC2712Y-TE85L TRANSISTOR 2SC2712Y-TE85L Ref. No. Part No. Description Remarks R166 R167 1-216-073-00 RES-CHIP 1-249-431-11 CARBON 10K 15K 5% 5% 1/10W 1/4W R168 R169 R170 R171 R172 1-216-073-00 1-216-073-00 1-247-843-11 1-216-089-00 1-216-073-00 RES-CHIP RES-CHIP CARBON RES-CHIP RES-CHIP 10K 10K 3.
MA-405 Ref. No. Part No. Description R306 R308 R310 R311 R313 1-216-033-00 1-216-091-00 1-216-295-00 1-216-295-00 1-249-437-11 RES-CHIP RES-CHIP SHORT SHORT CARBON 220 56K 0 0 47K 5% 5% 1/10W 1/10W R427 R440 R441 1-216-053-00 RES-CHIP 1-216-075-00 RES-CHIP 1-216-085-00 RES-CHIP 1.5K 12K 33K 5% 5% 5% 1/10W 1/10W 1/10W 5% 1/4W RES-CHIP RES-CHIP CARBON RES-CHIP RES-CHIP 47K 33K 47K 47K 3.
MA-405 Ref. No. Part No. Description Remarks R680 R701 1-249-417-11 CARBON 1-249-417-11 CARBON 1K 1K 5% 5% 1/4W 1/4W R702 R703 R704 R709 R710 1-216-061-00 1-249-412-11 1-216-043-91 1-216-049-00 1-216-049-00 RES-CHIP CARBON RES-CHIP RES-CHIP RES-CHIP 3.3K 390 560 1K 1K 5% 5% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 1/10W R711 R712 ! R723 R724 1-216-049-00 1-216-295-00 1-240-307-81 1-216-113-00 RES-CHIP SHORT FUSIBLE RES-CHIP 1K 0 560 470K 5% 1/10W 5% 5% 1/4W 1/10W Ref. No.
Ref. No. Part No. Description Remarks Ref. No. 7-14 Part No.
SLV-LX40/LX50/LX60S/LX70S Ref. No. Part No. Description Remarks Ref. No. Part No. Sony Corporation 9-921-786-11 NETWORK ENTERTAINMENT GROUP –7-15 86 – Description Remarks 20001B0800-1 2001. 2 Published by Quality Assurance Dept.