SON Y. 4-548-379-11(1) Bluetooth® Audio System Operating Instructions Mode d'emploi Manual de instrucciones The warranty for this product is included in this manual (page 38, 39). La garantie de ce produit est inclus dans le present manuel (page 41). Owner's Record The model and serial numbers are located on the bottom of the unit. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. Serial No.
For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use. For details, see "Connection/Installation" (page 32). The nameplate indicating operating voltage, etc., is located on the bottom of the chassis. Warning FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC. POUR LES CLIENTS AUX ETATS-UNIS. NON APPLICABLE AU CANADA, V COMPRIS LA PROVINCE DE QUEBEC.
Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER'S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE. Dear customer, this product includes a radio transmitter.
Additional Information Table of Contents Warning .......................... ......... 2 Guide to Parts and Controls ................... 5 Getting Started Detaching the Front Panel .................... 7 Resetting the unit .......................... . 7 Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Preparing a BLUETOOTH Device ................ 8 Connecting an iPod/USB Device .............. 10 Connecting Other Portable Audio Device ....... 10 Updating the Firmware . . . . . .
Guide to Parts and Controls Main unit Front panel removed (inner panel) N-Mark Touch the control dial with Android phone to make BLUETOOTH connection. @] Disc slot L [ID Display window rn:J [I] Front panel release button [g) SRC (source) Turn on the power. Change the source. -OFF Press and hold for 1 second to turn the source off and display the clock. Press and hold for more than 2 seconds to turn off the power and the display.
Press A to thumbs up, or • to thumbs down in Pandora®(page 14). 4 (repeat} ~(shuffle} MIC (page 16} PAUSE [H) MEGA BASS Press to turn on/off the MEGA BASS function . M] PTY (program type} Select PTY in RDS. CAT (category} (MEX-N5100BT only) Select radio channels in SiriusXM. [1§] AUX input jack [1] DSPL (display) Press to change display items. - SCRL (scroll} Press and hold to scroll a display item.
Getting Started Detaching the Front Panel You can detach the front panel of this unit to prevent theft. 1 Resetting the unit Before operating the unit for the first time, after replacing the car battery, or changing the connections, you must reset the unit. Press RESET on the inner panel with a ball-point pen, etc., after detaching the front panel. Press and hold OFF CD until the unit turns off, press the front panel release button @, then pull the panel towards you to remove.
Preparing a BLUETOOTH Device You can enjoy music, or perform handsfree calling depending on the BLUETOOTH compatible device such as a smartphone, cellular phone and audio device (hereafter "BLUETOOTH device" if not otherwise specified). For details on connecting, refer to the operating instructions supplied with the device. Before connecting the device, turn down the volume of this unit; otherwise, loud sound may result.
To start playback To install the microphone For details, see "Playing a BLUETOOTH Device" (page 13). For details, see "Installing the microphone (MEXN5100BT only)" (page 35). To cancel pairing Perform step 2 to cancel the pairing mode after this unit and the BLUETOOTH device are paired. To use a paired device, connection with this unit is required. Some paired devices will connect automatically.
Connecting an iPod/USB Device 1 2 Listening to the Radio Turn down the volume on the unit. Connect the iPod/USB device to the unit. Listening to the Radio To connect an iPod/iPhone, use the USB connection cable for iPod (not supplied). To listen to the radio, press SRC to select [TUNER]. 1 Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2). 2 Press MENU, rotate the control dial to select [SET GENERAL], then press it. 3 Rotate the control dial to select [SET BTM], then press it.
Using Radio Data System (RDS) 1 2 Press PTY during FM reception. Rotate the control dial until the desired program type appears, then press it. The unit starts to search for a station broadcasting the selected program type.
To set a parental control The parental control feature allows you to limit access to SiriusXM channels with mature content. When enabled, the parental control feature requires you to enter a passcode to tune to the locked channels. Information on setting up the passcode and locking channels can be found below. 1 2 3 4 Press MENU and rotate the control dial. Select [SET GENERAL] -+ [SET PARENTAL] -+ [SET LOCK SEL]-+ [SET LOCK-ON].
To remove the device Stop playback, then remove the device. Searching and Playing Tracks Caution for iPhone When you connect an iPhone via USB, phone call volume is controlled by the iPhone, not the unit. Do not inadvertently increase the volume on the unit during a call, as a sudden loud sound may result when the call ends. 1 During playback, press c; (repeat) or ~ (shuffle) repeatedly to select the desired play mode. Playback in the selected play mode may take time to start.
Listening to Pandora® Pandora® is available to stream music through your iPhone and Android phone. You can control Pandora® on a BLUETOOTH connected iPhone/ Android phone from this unit. The Pandora® service is not available in some countries/regions. Available Operations in Pandora® "Thumbs Up" or "Thumbs Down" feedback allows you to personalize stations. 1 During playback, press.._ (Thumbs Up) or T (Thumbs Down).
1 Handsfree Calling (via BLUETOOTH only} 1 Press CALL, rotate the control dial to select [RECENT CALL], then press it. A list of the call history appears. To use a cellular phone, connect it with this unit. For details, see "Preparing a BLUETOOTH Device" (page 8). 2 ~ The phone call starts. 1 Press CALL, rotate the control dial to select [DIAL NUMBER], then press it. 2 Rotate the control dial to enter the phone number, and lastly select [ ] (space), then press ENTER*.
You can make a call by saying the voice tag stored in a connected cellular phone that has a voice dialing function. 1 Press CALL, rotate the control dial to select [VOICE DIAL], then press it. Alternatively, press VOICE while the "SongPal" function is off. 2 Say the voice tag stored on the cellular phone. Your voice is recognized, and the call is made. To cancel voice dialing Press VOICE. Available Operations during Call To adjust the ringtone volume Rotate the control dial while receiving a call.
Selecting the source or application You can operate to select the desired source or application on iPhone/Android phone. To select the source Press SRC repeatedly. Alternatively, press SRC, rotate the control dial to select the desired source, then press ENTER. To display the source list Activating voice recognition (Android phone only} By registering applications, you can control an application by voice command. For details, refer to the help of the application.
Using Siri Eyes Free Siri Eyes Free allows you to use an iPhone handsfree by simply speaking into the microphone. This function requires you to connect an iPhone to the unit with BLUETOOTH Auto Pairing. Availability is limited iPhone 4s or later. Make sure that your iPhone is running the latest iOS version. You must complete BLUETOOTH registration and connection configurations for the iPhone with the unit in advance. For details, see "Preparing a BLUETOOTH Device" {page 8).
AUTO OFF Shuts off automatically after a desired time when the unit is turned off: [NO], [30S] {30 seconds), [30M] {30 minutes), [60M] {60 minutes). REAR/SUB (MEX-N4100BT only) Switches the audio output: [SUB-OUT] (subwoofer), [REAR-OUT] (power amplifier). (Available only while the source is off and the clock is displayed.) STEERING Registers/resets the setting of the steering wheel remote control. (Available when connected with the connection cable (not supplied).
EQ10 SETTING Sets [CUSTOM] of EQ10. BASE Selects a preset equalizer curve as a basis for further customizing: [BAND1] 32Hz, [BAND2] 63 Hz, [BAND3] 125Hz, [BAND4] 250Hz, [BANDS] 500 Hz, [BAND6] 1 kHz, [BAND7] 2kHz, [BANDS] 4kHz, [BAND9] 8 kHz, [BAND10] 16kHz. The volume level is adjustable in 1 dB steps, from -6 dB to +6 dB.
HPF {high pass filter) HPF FREQ {high pass filter frequency) Selects the front/rear speaker cut-off frequency: [OFF], [50Hz], [60Hz], [80Hz), (100Hz], (120Hz). HPF SLOP {high pass filter slope) Selects the HPF slope {effective only when [HPF FREQ] is set to other than [OFF]): [1], [2], [3]. AUX VOL {AUX volume level} Adjusts the volume level for each connected auxiliary device: [+18 dB]- [O dB)- (-8 dB]. This setting negates the need to adjust the :\olume level between sources.
AUTO ANS (auto answer) Sets this unit to answer an incoming call automatically: [OFF], [1] (about 3 seconds), [2] (about 10 seconds). AUTOPAIR (auto pairing) Start BLUETOOTH pairing automatically when iOS device version 5.0 or later is connected via USB: [ON], [OFF]. BT SIGNL (BLUETOOTH signal) (page 9) Activates/deactivates the BLUETOOTH function. BT INIT (BLUETOOTH initialize) Initializes all the BLUETOOTH related settings (pairing information, preset number, device information, etc.): [YES], [NO].
Notes on CD-R/CD-RW discs • If the multi-session disc begins with a CD-DA session, it is recognized as a CO-DA disc, and other sessions are not played. • Discs that this unit CANNOT play - CD-R/CD-RW of poor recording quality. - CD-R/CD-RW recorded with an incompatible recording device. - CD-R/CD-RW which is finalized incorrectly. - CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to IS09660 Levei1/Level 2, Joliet/Romeo or multisession.
Notes on the lithium battery • Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. • Wipe the battery with a dry cloth to ensure a good contact. • Be sure to observe the correct polarity when installing the battery. • Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean.
Power amplifier section Output: Speaker outputs Speaker impedance: 4- 8 ohms Maximum power output: 55 W x 4 (at 4 ohms) General Outputs: Audio outputs terminal: MEX-N5100BT: front, rear, sub MEX-N4100BT: front, rear/sub switchable Power antenna (aeriai)/Power amplifier control terminal (REM OUT) Inputs: SiriusXM input terminal {MEX-N5100BT only) Remote controller input terminal Antenna (aerial) input terminal MIC input terminal AUX input jack (stereo mini jack) USB port Power requirements: 12 V DC car batt
documentation and/or other materials provided with the distribution. - Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
The disc does not play. ~ Defective or dirty disc. ~ The CD-R/CD-RW is not for audio use (page 23). MP3/WMA/AAC files cannot be played. ~The disc is incompatible with the MP3/WMA/AAC format and version. For details on playable discs and formats, visit the support site on the back cover. MP3/WMA/AAC files take longer to play than others. ~ The following discs take a longer time to start playback. -A disc recorded with a complicated tree structure. -A disc recorded in Multi Session.
The phone sound quality is poor. -+ Phone sound quality depends on reception conditions of cellular phone. - Move your car to a place where you can enhance the cellular phone's signal if the reception is poor. The volume of the connected audio device is low (high). -+ Volume level will differ depending on the audio device. -Adjust the volume of the connected audio device or this unit. The sound skips during playback of a BLUETOOTH audio device.
READ: Now reading information. -+ Wait until reading is complete and playback starts automatically. This may take some time depending on the disc structure. USB ERROR: The USB device cannot be played. -+ Connect the USB device again. USB NO DEV: A USB device is not connected or recognized. -+ Make sure the USB device or USB cable is securely connected. USB NO MUSIC: There is no playable file. APP DISPLAY: A screen setting display of the application is open.
PAN MAINT: The Pandora® server is under maintenance. ~ Wait for a while, then try again. PAN OPEN APP- PRESS PAUSE: Pandora® is not running. ~ Launch the Pandora® application on the mobile device, then press PAUSE. PAN RESTRICT: Pandora ® is not available outside your country. PLEASE LOGIN - PANDORA APP: You are not logged into your Pandora® account. ~ Disconnect the device, log into your Pandora® account, then connect the device again. UPDATE PAN: An old version of Pandora® is connected.
For steering wheel remote control operation: ERROR: An error occurred during the function registration. -+ Register again from the function where the error occurred (page 19). TIMEOUT: The function registration failed due to a timeout. -+ Try completing the registration while [REGISTER] is blinking (about 6 seconds) (page 19). If these solutions do not help improve the situation, consult your nearest Sony dealer.
Connection/1 nsta llation Parts List for Installation CD Cautions • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power supply leads only after all other leads have been connected. • Be sure to insulate any loose unconnected leads with electrical tape for safety. ® ~ ® /.: 0 Sx max.
Connection (For MEX-NS100BT) Subwoofer*t H®l .......................................................J.!i~~~@~!~w~~t·.~-. ~ • , .................................................J.I!lt''¥~:'1:M:111."! ~ .. ~ !" ...........................................A'.W!.I!!'M:W!P.'' ~ .. ~ Power amplifier*! •MM•iiJWM from a w1red · remote control ................................. :-:':::! .................. (not supplied)*4 Satellite radio tuner (SiriusXM)*t ............................................ AW:V.
Connection (For MEX-N4100BT) Subwoofer*l from a wired remote control ·"·········· ,•••.•. •.•• >. .Q .III~J>. u (not supplied}*4 f) 0 *1 *2 *3 *4 Not supplied Speaker impedance: 4- 8 Q x 4 RCA pin cord (not supplied) Depending on the type of car, use an adaptor for a wired remote control (not supplied). 34GB For details, see "Making e connections" (page 35}. Microphone XA-MC10*1*5 *5 Whether in use or not, route the microphone input cord such that it does not interfere with driving operations.
Speaker connection 0 To a common ground (earth) point First connect the black ground (earth) lead, then connect the yellow and red power supply leads. EJ To the +12 V power terminal which is energized at all times Be sure to first connect the black ground (earth) lead to a common ground (earth) point.
Notes on installing the connection cable RC-SR1 (not supplied) • Refer to the support sites on the back cover for details, then connect each lead properly to the appropriate leads. Making an improper connection may damage the unit. • Depending on the type of car, be sure to insulate the unused leads with electrical tape for safety. • Do not connect this cable when the steering wheel remote control is not used. • Consulting the dealer or an experienced technician for help is recommended.
Mounting the unit in a Japanese car You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. TOYOTA to dashboard/center console When replacing the fuse, be sure Fuse (10 A) to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
This warranty is valid only in the United States. SONY® LIMITE D WARRANTY(u.s.~n~;rAudio 1 Sony Electronics Inc. ("Sony") warrants this product against defects in material or workmanship for the time periods and as set forth below when purchased directly from Sony or a Sony Retailer. Pursuant to this Limited Warranty, Sony will, at its option, (i) repair the product using new or refurbished parts or (ii) replace the product with a new or refurbished product.
This warranty is valid only in Canada. SONY Consumer Warranty (canada only) Sony of Canada Ltd. (hereinafter referred to as "Sony") hereby warrants, subject to the terms and conditions herein set forth, this product against defects in material and workmanship during the specified warranty period.
http:/ /esupport.sony.com/ 1 Read Trouble shootin g in these Operating Instructions. 2 Please contact (U.S.A. only}; Call URL 1-800-22 2-7669 http://www.SO NY.com http:/ /www.sony .
SONYe 4-467-585-01 For Dealers For display purposes it is necessary to secure the front panel to the unit as shown below. Secure the screw on the left side of the unit.
4-485-223-11(1) SONY: - MEX-XXXXXXX - ---0 SERIAL NO. ._1 MEX-XXXXXXX X-XXX-XXX-XX SERIAL NO.I X-XXX-XXX-XX d I ) IH til ++HEll!' e I I 3.t. UfUI ' 1' 61.1.8 IMPORTANT NOTICE FOR DEALER: NOTA IMPORTANTE PER IL RIVENDITORE: MAKE SURE THE SERIAL NUMBERS ON THE BOTTOM OF THE UNIT 0 AND THE REAR OF THE FRONT PANEL G) ARE IDENTICAL. OTHERWISE THE NFC FUNCTION OF THIS UNIT WILL NOT WORK.
