- 4-698-030-11(1) SONY: ----- Bluetooth® Audio System Operating Instructions GB Mode d’emploi FR Owner’s Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. MEX-GS820BT Serial No. To cancel the demonstration (DEMO) display, see page 21. For the connection/installation, see page 39.
For safety, be sure to install this unit in the dashboard of the car as the left side of the unit becomes hot during use. For details, see “Connection/Installation” (page 39). The nameplate indicating operating voltage, etc., is located on the bottom of the chassis. Warning FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC. POUR LES CLIENTS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA PROVINCE DE QUÉBEC.
This device complies with Part 15 of the FCC Rules and Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
Important notice Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE. Dear customer, this product includes a radio transmitter.
Settings Table of Contents Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Guide to Parts and Controls. . . . . . . . . . . . . 6 Getting Started Detaching the Front Panel . . . . . . . . . . . . . . 8 Resetting the Unit. . . . . . . . . . . . . . . . . . . . . 8 Setting the Clock. . . . . . . . . . . . . . . . . . . . . . 8 Checking the Battery Voltage . . . . . . . . . . . 8 Preparing a BLUETOOTH Device . . . . . . . . . 9 Connecting a USB Device. . . . . . . . . . . . . . .
Guide to Parts and Controls Main unit VOICE (page 18, 20, 21) Press and hold for more than 2 seconds to activate voice dial, voice recognition (Android™ smartphone only), or the Siri function (iPhone only). N-Mark Touch the control dial with Android smartphone to make BLUETOOTH connection. Front panel removed (inner panel) ~ [IT] Front panel release button Disc slot SRC (source) Turn on the power. Change the source.
(back) Return to the previous display. MODE (page 12, 13, 17, 19) RM-X231 Remote commander Receptor for the remote commander Number buttons (1 to 6) Receive stored radio stations. Press and hold to store stations. ALBUM / Skip an album for audio device. Press and hold to skip albums continuously. (Not available when a USB device in Android mode or iPod is connected.) Press to thumbs up, or to thumbs down in Pandora® (page 17).
Getting Started Detaching the Front Panel You can detach the front panel of this unit to prevent theft. 1 Press and hold OFF until the unit turns off, press the front panel release button , then pull the panel towards you to remove. Resetting the Unit Before operating the unit for the first time, or after replacing the car battery or changing connections, you must reset the unit. Press RESET on the inner panel with a ballpoint pen, etc., after detaching the front panel.
Preparing a BLUETOOTH Device You can enjoy music, or perform handsfree calling depending on the BLUETOOTH compatible device such as a smartphone, cellular phone and audio device (hereafter “BLUETOOTH device” if not otherwise specified). For details on connecting, refer to the operating instructions supplied with the device. Before connecting the device, turn down the volume of this unit; otherwise, loud sound may result.
6 Select [MEX-GS820BT] (your model name) shown in the display of the BLUETOOTH device. If your model name does not appear, repeat from step 2. Connecting with a paired BLUETOOTH device To use a paired device, connection with this unit is required. Some paired devices will connect automatically. 0>))) DR-BT30Q 7 MEX-GS820BT 7 If passkey* input is required on the BLUETOOTH device, input [0000]. * Passkey may be called “Passcode,” “PIN code,” “PIN number” or “Password,” etc., depending on the device.
To install the microphone For details, see “Installing the microphone” (page 42). Connecting with an iPhone/iPod (BLUETOOTH Auto Pairing) Connecting a USB Device 1 2 Turn down the volume on the unit. Connect the USB device to the unit. To connect an iPod/iPhone, use the USB connection cable for iPod (not supplied). When an iPhone/iPod with iOS5 or later installed is connected to the USB port, the unit is paired and connected with the iPhone/iPod automatically.
Listening to the Radio Listening to the Radio To listen to the radio, press SRC to select [TUNER]. Storing automatically (BTM) 1 Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2). 2 Press MENU, rotate the control dial to select [GENERAL], then press it. 3 Rotate the control dial to select [SET BTM], then press it. The unit stores stations in order of frequency on the number buttons. Tuning 1 Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2). 2 Perform tuning.
Notes Listening to the SiriusXM Radio Activating your SiriusXM Subscription Only SiriusXM brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Connect Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.
3 Enter the passcode by rotating the control dial on the unit or pressing / on the remote commander. To move the entry position, press / (SEEK –/+) on the unit or / on the remote commander. The initial passcode is [0000]. 4 After entering the passcode, press ENTER. Playback Playing a Disc 1 Insert the disc (label side up). To unlock the channels, select [GENERAL] [SXM PARENTAL] [LOCK SELECT] [LOCK-OFF]. To change the passcode 1 Press MENU and rotate the control dial.
• Playback of the following files is not supported. MP3/WMA/AAC/FLAC: – copyright-protected files – DRM (Digital Rights Management) files – Multi-channel audio files MP3/WMA/AAC: – lossless compression files WAV: – Multi-channel audio files Before making a connection, select the USB mode (Android mode or MSC/MTP mode) depending on the USB device (page 22). 1 Connect a USB device to the USB port (page 11). Playback starts.
Searching a track by name (QuickBrowZer™) Not available when a USB device in Android mode or iPod is connected. 1 During CD, USB or BT AUDIO*1 playback, press Q (browse)*2 to display the list of search categories. When the track list appears, press (back) repeatedly to display the desired search category. *1 Available only for audio devices supporting AVRCP (Audio Video Remote Control Profile) 1.4 or above.
When activating the BLUETOOTH function Handsfree Calling (via BLUETOOTH only) You can adjust the volume level. Press MENU, then select [SOUND] [SET BTA VOL] (page 24). Available Operations in Pandora® “Thumbs” feedback To use a cellular phone, connect it with this unit. You can connect two cellular phones to the unit. For details, see “Preparing a BLUETOOTH Device” (page 9). ~□ “Thumbs Up” or “Thumbs Down” feedback allows you to personalize stations.
3 Rotate the control dial to select an initial from the initial list, then press it. 4 Rotate the control dial to select a name from the name list, then press it. 5 Rotate the control dial to select a number from the number list, then press it. By redial 1 Press CALL. When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it. 2 Rotate the control dial to select [REDIAL], then press it. The phone call starts. The phone call starts.
Available Operations during Call To adjust the ringtone volume Rotate the control dial while receiving a call. To adjust the talker’s voice volume Rotate the control dial during a call. To adjust the volume for the other party (Mic gain adjustment) Press MIC. Adjustable volume levels: [MIC-LOW], [MICMID], [MIC-HI]. To reduce echo and noise (Echo Canceler/Noise Canceler Mode) Press and hold MIC. Settable mode: [EC/NC-1], [EC/NC-2].
If the device number appears Make sure that the number is displayed (e.g., 123456), then select [Yes] on the iPhone/Android smartphone. To terminate connection 1 Press MENU, rotate the control dial to select [SONY APP], then press it. Making sound and display settings You can adjust the settings relating to sound and display via iPhone/Android smartphone. For details on settings, refer to the help of the application. 2 Rotate the control dial to select [CONNECT], then press it.
2 Press and hold VOICE for more than 2 seconds. Settings The voice command display appears. 3 After the iPhone beeps, speak into the microphone. The iPhone beeps again, then Siri starts responding. To deactivate Siri Eyes Free Press VOICE. Canceling the DEMO Mode You can cancel the demonstration display which appears when the source is off and the clock is displayed. 1 Press MENU, rotate the control dial to select [GENERAL], then press it.
General Setup (GENERAL) DEMO (demonstration) Activates the demonstration: [ON], [OFF]. CLOCK-ADJ (clock adjust) (page 8) CAUT ALM (caution alarm) Activates the caution alarm: [ON], [OFF] (page 8). (Available only while the source is off and the clock is displayed.) BEEP (beep) Activates the beep sound: [ON], [OFF]. AUTO OFF (auto off) Shuts off automatically after a certain time when the unit is turned off: [ON] (30 minutes), [OFF].
SXM RESET (SiriusXM reset) Initializes the SiriusXM Connect Vehicle Tuner settings (preset channels/parental lock): [YES], [NO]. (Available only when SiriusXM is selected.) FIRMWARE (firmware) (Available only while the source is off and the clock is displayed.) Checks/updates the firmware version. For details, visit the support site on the back cover. FW VERSION (firmware version) Displays current firmware version. FW UPDATE (firmware update) Enters firmware update process: [YES], [NO].
FADER (fader) Adjusts the relative level: [FRONT-15] – [CENTER] – [REAR-15]. DSEE (digital sound enhancement engine) Improves digitally compressed sound by restoring high frequencies lost in the compression process: [ON], [OFF]. This setting can be memorized for each source other than the tuner. AAV (advanced auto volume) Adjusts the playback volume level of all playback sources to the optimum level: [ON], [OFF].
Display Setup (DISPLAY) DIMMER (dimmer) Changes the display brightness: [OFF], [ON], [AT] (auto), [CLK] (clock). ([AT] is available only when the illumination control lead is connected, and the head light is turned on.) To set this function to be active only during a fixed period, select [CLK], then set the start and end times. – To set the brightness when the dimmer function is activated: Set [DIMMER] to [ON], then adjust [BRIGHTNESS].
BT INIT (BLUETOOTH initialize) Initializes all the BLUETOOTH related settings (pairing information, device information, etc.): [YES], [NO]. When disposing the unit, initialize all the settings. (Available only while the source is off and the clock is displayed.) Additional Information Updating the Firmware To update the firmware, visit the support site on the back cover, then follow the online instructions.
• This unit is designed to play discs that conform to the Compact Disc (CD) standard. DualDiscs and some of the music discs encoded with copyright protection technologies do not conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this unit. • Discs that this unit CANNOT play – Discs with labels, stickers, or sticky tape or paper attached. Doing so may cause a malfunction, or may ruin the disc. – Discs with non-standard shapes (e.g., heart, square, star).
Maintenance Specifications Replacing the lithium battery of the remote commander FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC. POUR LES CLIENTS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA PROVINCE DE QUÉBEC. Under normal conditions, the battery will last approximately 1 year. (The service life may be shorter, depending on the conditions of use.) When the battery becomes weak, the range of the remote commander becomes shorter.
*3 may be less than the measured value if folder/ file names contain many characters USB Player section Interface: USB (High-speed) Maximum current: Front: 1 A Rear: 1.5 A Maximum number of recognizable files (tracks): 10,000 Compatible Android Open Accessory protocol (AOA): 2.0 Corresponding codec: MP3 (.mp3) Bit rate: 8 kbps – 320 kbps (Supports VBR (Variable Bit Rate)) Sampling rate: 16 kHz – 48 kHz WMA (.wma) Bit rate: 32 kbps – 192 kbps (Supports VBR (Variable Bit Rate)) Sampling rate: 32 kHz, 44.
Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information. Design and specifications are subject to change without notice. Copyrights {()) READY SiriusXM Connect Vehicle Tuner and Subscription sold separately. www.siriusxm.com Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc.
Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. For details on using the fuse and removing the unit from the dashboard, see “Connection/Installation” (page 39). If the problem is not solved, visit the support site on the back cover. General No power is being supplied to the unit.
Radio reception Stations cannot be received. The sound is hampered by noises. The connection is not correct. – If your car has built-in radio antenna (aerial) in the rear/side glass, connect an REM OUT lead (blue/white striped) or accessory power supply lead (red) to the power supply lead of a car’s antenna (aerial) booster. – Check the connection of the car antenna (aerial). – If the auto antenna (aerial) will not extend, check the connection of the power antenna (aerial) control lead.
NFC function One-touch connection (NFC) is not possible. If the smartphone does not respond to the touching. – Check that the NFC function of the smartphone is turned on. – Move the N-Mark part of the smartphone closer to the N-Mark part on this unit. – If the smartphone is in a case, remove it. NFC receiving sensitivity depends on the device. If One-touch connection with the smartphone fails several times, make BLUETOOTH connection manually.
The volume of the connected audio device is low (high). Volume level will differ depending on the audio device. – Adjust the volume of the connected audio device or this unit (page 24). The sound skips during playback of a BLUETOOTH audio device. Reduce the distance between the unit and the BLUETOOTH audio device. If the BLUETOOTH audio device is stored in a case which interrupts the signal, remove the audio device from the case during use.
Pandora® operation Pandora® connection is not possible. Shut down the Pandora® application on the mobile device, and then launch it again. CD PUSH EJT: The disc could not be ejected properly. Press (eject). LLLL or 7777 : The beginning or the end of the disc has been reached. Messages For USB device playback: The following messages may appear or flash during operation. HUB NO SUPRT: USB hubs are not supported. INVALID The selected operation could be invalid.
For BLUETOOTH function: BTA NO DEV: The BLUETOOTH device is not connected or recognized. Make sure the BLUETOOTH device is securely connected, or the BLUETOOTH connection is established with the BLUETOOTH device. ERROR: The selected operation could not be performed. Wait for a while, then try again. NO DEVICE: The BLUETOOTH device supporting HFP (Handsfree Profile) is not connected or recognized.
NO STATIONS: No stations on your account. Create the station on the mobile device. NOT ALLOWED: The selected operation is not allowed. “Thumbs” feedback is not allowed. – Wait until the commercial ends. – Some functions, such as Shared Station, do not permit feedback. Wait until the next track begins, or select another station on the list. Bookmark is not allowed. – Wait until the commercial ends. – Select another track or station, then try it again.
CODE ERROR The entered passcode is incorrect. – Enter the correct passcode. – If you forget your passcode, perform [SET SXM RESET] in [GENERAL] (page 23). Note that performing [SXM RESET] will initialize all the SiriusXM settings and stored contents in the SiriusXM Connect Vehicle Tuner. NO SIGNAL SiriusXM Connect Vehicle Tuner is having difficulty receiving the SiriusXM satellite signal. – Verify that your vehicle is outdoors with a clear view of the sky.
Connection/Installation Parts List for Installation Cautions • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power supply leads only after all other leads have been connected. • Be sure to insulate any loose unconnected leads with electrical tape for safety. ×2 5 × max.
Connection Subwoofer*1 *3 *3 *3 Power amplifier*1 Satellite radio tuner (SiriusXM)*1 *5*6 *10 *1 Smartphone*8, iPod/ iPhone*9, USB device o,. (G)(G} I!m t==========~:,. White White/black striped Gray Gray/black striped Green Front speaker*1*2*11 = L=====~~~·.. ~~ mI! Green/black striped Purple l===============:A:cc~ + Purple/black striped Red Blue/white striped Orange/white striped Black Yellow 0 Rear speaker*1*2*11 O REM OUT (MAX 0.4A) .. • ILLUMINATION O . .
*1 *2 *3 *4 Not supplied Speaker impedance: 4 Ω – 8 Ω × 4 RCA pin cord (not supplied) Depending on the type of car, use an adaptor for a wired remote control (not supplied). For details on using the wired remote control, see “Using the wired remote control” (page 43). *5 Whether in use or not, route the microphone input cord such that it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet.
Subwoofer Easy Connection You can use a subwoofer without a power amplifier when it is connected to a rear speaker cord. Installing the microphone To capture your voice during handsfree calling, you need to install the microphone . Front speaker = Subwoofer Note Use a subwoofer with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.
Using the wired remote control When using the steering wheel remote control Installation of the connection cable RC-SR1 (not supplied) is required before use. Installation Removing the protection collar and the bracket 1 To enable the steering wheel remote control, select [SET STEERING] [EDIT CUSTOM] to make the registration (page 22). When the registration completes, the steering wheel remote control becomes available.
Mounting the unit in a Japanese car Mounting the unit in the dashboard • Before installing, make sure the catches on both sides of the bracket are bent inwards 2 mm (3/32 in). • For Japanese cars, see “Mounting the unit in a Japanese car” (page 44). You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. TOYOTA to dashboard/center console CAUTION Do not touch the left side of the unit when removing from the dashboard.
Detaching and attaching the front panel For details, see “Detaching the Front Panel” (page 8). Resetting the unit For details, see “Resetting the Unit” (page 8). Fuse replacement When replacing the fuse, Fuse (15 A) be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
Support site Site d’assistance If you have any questions or for the latest support information on this product, please visit the web site below: Si vous avez des questions ou si vous souhaitez consulter les toutes dernières informations techniques sur ce produit, rendez-vous sur le site Web suivant : http://esupport.sony.com/ If you have any questions/problems regarding this product, try the following: 1 Read Troubleshooting in these Operating Instructions. 2 Please contact (U.S.A.
SONY MEX-GS820BT High-Power GS Series CD Receiver with Bluetooth ® CD receiver with NFC and Dual Bluetooth5 connectivity, voice control, EXTRA BASS and a 4 x 100W1 built-in amp. r Dual Bluetooth connectivity lets you connect two smartphones simultaneously 5 r Hi-power 100 watt x 4 Digital Amp (45W x 4 CEA RMS wattage) 1 r Take control with the Music Center app3 1 -o·- ·:. . 111 • .::UNY -- -- --- • ~ .
SONY Create virtual speakers right in front of you Sound waves are directional, so if your speakers are in your doors or under your dash, the audio may seem muddy or unclear. Dynamic Stage Organizer adjusts the signal, improving the stereo positioning so music sounds like it's coming from right in front of you. Bring out the bass Hit the EXTRA BASS button for deep, punchy sound at any volume. Switch between two settings for different intensities of bass boost.
SONY TRACK +/- Yes Bluetooth Feature # of records connected 9 (HFP+Audio) Call history (# of) Yes (20 numbers via PBAP) Digital Sound Enhancement Engine (DSEE) Yes EQ Yes (EQ10) EXTRA BASS Yes (1,2) High Pass Filter Yes (OFF/50/60/80/100/120) High Voltage Pre Out 5 Volt Call history browse with PBAP Yes (Combined call) Call Volume Level Control Yes Low Pass Filter Yes (50/60/80/100/120) Connection Status (maximum #) [2HFP+1Audio] Output Power (4ohm, 1kHz,16V) 100W Echo/Noise Cancel
SONY Steering Wheel Remote Input FM: Tuning range (MHz) 87.5-107.9 FM: Usable sensitivity (75 ohm) (dBf) 8 Others / Instruction Manual Language MW: Tuning range(kHz) 530-1710 English Yes USB Mass Strage Device Control Feature French Yes Yes NFC Feature NFC One-touch connection Yes CODEC (for USB) MP3, WMA, AAC, FLAC, WAV Others / Cosmetic Print Jump Mode Yes **Wx4 100 Yes List Browsing (Folders/Files) Yes Bluetooth logo Cosmetic Sticker Sticker (100W x4 Max.
SONY 1. Rated Power: CEA2006 Standard Power Output: 45 Watts RMS × 4 at 4 Ohms 1% THD+N SN Ratio: 80 dBA (reference: 1 Watt into 4 Ohms). 2. Siri is available on iPhone 4s or later, iPad Pro, iPad Air or later, iPad (3rd generation) or later, iPad mini or later, and iPad touch (5th generation or later) and requires internet access. Siri may not be available in all languages or in all areas, and features may vary by area. Cellular data charges may apply. 3.
SONY. 4- 467-585-01 For Dealers For display purposes it is necessary to secure the front panel to the unit as shown below. Secure the screw on the left side of the unit.
SONY. 4-485-223-12{1) ] [ l _____f) SERIAL No... .€.1.§t~..iii■i■t•i~I~~~~0 IMPORTANT NOTICE FOR DEALER: MAKE SURE THE SERIAL NUMBERS ON THE BOTTOM OF THE UNIT 0 AND THE REAR OF THE FRONT PANEL C, ARE IDENTICAL. OTHERWISE THE NFC FUNCTION OF THIS UNIT WILL NOT WORK. AVIS IMPORTANT POUR LE REVENDEUR : ASSUREZ-VOUS QUE LES NUMEROS DE SERIE INDIQUES SOUS L'APPAREIL O ET A L'ARRIERE DE LA FA(ADE C, SONT IDENTIQUES. SINON, LA FONCTION NFC DE CET APPAREIL NE POURRA PAS FONCTIONNER.
BELANGRIJKE KENNISGEVING VOOR VERDELER: GA NA OF DE SERIENUMMERS OP DE ONDERKANT VAN HET APPARAAT Q EN OP DE ACHTERKANT VAN HET VOORPANEEL G) IDENTIEK ZIJN. IS DIT Nl~T HET GEVAL, DAN ZAL DE NFC-FUNCTIE VAN DIT APPARAAT NIET WERKEN. BA>KHOE C005LUEHME AJlA AMnEPOB: Y6EtJ.VITECb, 4TO CEPVIVIHblE HOMEPA HA HVl)KHEL'l nAHEnVI YCTPOVICTBA G VI HA 3At].HEli1 4ACTVI nEPEAHEL'l nAHEnVI G) VltlE HTVl 4 Hbl. B nPOTVIBHOM cnY4AE c.t>YHKUVI~ NFC 3TOro YCTPOL'lCTBA HE 6YAET PA60TAT6.
11111111 11111111111111 4-597-061-11 II SONY@ LIMITED WARRANTY Car Audio U.S. and Canada only- 3 years Sony Electronics Inc. solely for purchases made in the United States and Sony of Canada Ltd. solely for purchases made in Canada (collectively "Sony") warrants this product against defects in material or workmanship for the original owner and any subsequent end user owner(s) ("You" or ''Your") for the time period set forth above as set forth herein.
SONY@ GARANTIE LIMITEE I E.-U. et Canada uniquement - 3 ans Sony Electronics Inc. exclusivement pour les achats effectues aux Etats-Unis et Sony du Canada Ltee. exdusivement pour les achats effectues au Canada (collectivement « Sony ») garantit ce produit contre les defauts de materiaux ou de fabrication pour le proprietaire d'origine et tousles proprietaires utilisateurs finaux suivants (« Vous » ou «Vos») pendant la periode definie ddessus et comme indique clans les presentes.
