3-205-808-12(1) UHF Synthesized Wireless Microphone Operating Instructions GB Mode d’emploi FR Bedienungsanletung DE Manual de instrucciones ES WRT-807B [U62] [U66] 2001 Sony Corporation [CE57] [CE62] [CE67]
Notice for customers in the U.S.A. Owner’s Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony Use of Sony wireless devices is regulated by the Federal Communications Commission as described in Part 74 subpart H of the FCC regulations and users authorized thereby are required to obtain an appropriate license. dealer regarding this product.
Notice for customers in Canada: Avis pour les clients au Canada: Use of Sony wireless devices is regulated by the Industry L’usage des appareils sans-fil Sony est réglé par l’Industrie Canada as described in their Radio Standard Specification Canada comme décrit dans leur Cahier des Normes RSS-123. Radioélectriques CNR-123. A licence is normally required. The local district office of Une licence est normalement requise. Le bureau de Industry Canada should therefore be contacted.
Notice for customers in Europe Spécifications particulières pour les consommateurs européens Hinweis für Kunden in Europa Aviso para los usuarios en Europa U.K. Belgium Luxembourg Germany Norway Denmark France Italy Sweden Switzerland Finland Iceland Austria Netherland 854.125 - 862 MHz 854.125 - 862 MHz 854.125 - 862 MHz, 800 - 822 MHz 798 - 822 MHz 800 - 820 MHz 800.100 - 819.
Por la presente, Sony Corporation, declara que este WRT-807B cumple con los requisitos esenciales y otras disposiciones pertinentes de la Directiva 1999/5/EC. Nota: En algunos países, es posible utilizar bandas de frecuencias adicionales con el consentimiento de las autoridades nacionales. Note for customers in Switzerland: Before use, a request of concession for a wireless microphone (Frequency Class 3) has to be submitted to Bakom.
English Table of Contents • The unit is designed for use in ambient temperature range of 0°C to 50°C (32°F to 122°F). • Do not place the unit on or near heat sources, such as lighting equipment, power amplifiers, or in a place subject to direct sunlight or excessive moisture. In such places, the external finish or internal parts of the unit may be damaged.
Introduction The WRT-807B is a UHF-synthesized wireless microphone for use in a 800-MHz band UHF-synthesized wireless microphone system. The WRT-807B operates in conjunction with the MB-806A with WRU-806B UHF Synthesized Tuner Unit for vocal concentration. The WRT-807B can be also used with existing Sony wireless microphone systems consisting of the WRT-805B/ 855B UHF Synthesized Transmitter and WRR-805B/855B/ 862B UHF Synthesized Tuner, etc.
LCD readout of various information The microphones LCD shows the current channel number, frequency, input attenuation setting, and residual battery power. The accumulated battery use time is also indicated (in oneminute increments) to allow precise monitoring of battery use. Notes on operation • When operating two or more microphones, keep the microphones separated from each other by a distance of at least 30 cm (1 foot). • Keep microphones at least 3 meters (10 feet) away from the receiving antenna.
Parts Identification 1 Wind screen Protects against noise caused by wind. 1 2 8 2 Liquid-crystal display A B C AF RF BATT 3 4 5 D Display example for CE62 model A AF (audio input) indication Lights whenever an audio signal stronger than the reference level is received. 7 B RF (antenna output) indication Lights during signal transmission from the antenna. C BATT (battery) indication Shows the battery condition. See “Battery indication” on page 7.
D CH (channel) indication Displays the transmitting channel. Each time you press the SET button in Transmit mode, the channel indication changes as follows. Transmitting channel To adjust these parameters, see “Changing the transmitting Channel” on page 8, “Changing the Input Attenuation Setting” on page 10 or “Resetting the Accumulated Battery Use Time Indication” on page 11. 3 SET button In Transmit mode, press this button to change the indicated items in the lower half of the liquid-crystal display.
Parts Identification 4 POWER indicator Lights when the microphone is on. 6 Antenna 5 POWER switch Turns the microphone ON or OFF. When you set this switch to ON without holding down any other button, the microphone enters Transmit mode, and the signal of the selected channel is transmitted. The HOLD switch appears when the POWER switch is set to ON. Set the HOLD switch to the lock position to prevent an accidental power cut-off during microphone operation. Locking the POWER switch ON ON , HOLD .
Power Supply The microphone can operate on one LR6 (size AA) alkaline battery continuously for about 5 hours at 25 ºC (77ºF). Battery indication Inserting the battery When you turn the power on, the battery condition is indicated by the BATT indication in the liquid-crystal display.
Settings Initiating Setting Mode Channel selection mode* Enter Setting mode to change the transmitting channel, the transmitting frequency and the attenuation level, or to reset the accumulated battery use time indication. Freqency selection mode Attenuator adjustment mode To enter Setting mode While holding down the SET button, turn the POWER switch to ON. Hold the SET button down until an indication appears on the liquid-crystal display.
2 Press the + or – button to select the channel number (or frequency). Pressing the + button cycles the indication in the order shown in separate “Sony Wireless Microphone System Frequency List.” Pressing the – button cycles the indications in the opposite direction. Channel selection mode + button – button Freqency selection mode + button – button Display example for CE62 model Hold down the button to change the channel number (or frequency) quickly.
Setting Changing the Input Attenuation Setting The input attenuation setting can be changed within a range of 0 dB to 21 dB (in 3-dB steps) in either Setting mode or Transmit mode. The next time you turn on the microphone (by turning the POWER switch to ON), the microphone enter Transmit mode with the selected attenuation setting.
Resetting the Accumulated Battery Use Time Indication 4 Turn the POWER switch to OFF to release Setting mode. The accumulated battery use time is the total time (in hours and minutes) the battery has been used. It is recorded whenever the WRT-807B is on. Reset the indication to 00:00 whenever you replace the battery. 1 2 Set the microphone to Setting mode. 3 Press the – button. The indication resets to 00:00.
Troubleshooting If you have any problem using this unit, use the following checklist. Should any problem persist, consult your Sony dealer. Symptom Meaning/Remedy The microphone does not turn on. • The + and – poles of the battery do not match those of the battery compartment. b Insert the battery with the poles correctly matched. • The battery is exhausted. b Replace the battery with new one. • The battery terminals in the microphone are dirty. b Clean the + and – terminals with a cotton swab.
Symptom Meaning/Remedy The sound is weak. • The attenuation level setting is too high. b The output level is low. Press the – button in attenuation level setting mode to lower the attenuation level. • The volume on the amplifier, mixer or tuner is low. b Adjust the volume. There is distortion in the sound. The attenuation level setting is too low. b The input level is extremely high. Press the + button in attenuation level setting mode to raise the attenuation level.
Specifications Transmitter and modulator section Oscillator Crystal controlled PLL synthesizer Type of emission F3E Carrier frequencies CE57 model: 758.025 to 782.000 MHz CE62 model: 798.025 to 822.000 MHz CE67 model: 838.025 to 862.000 MHz U62 model: 758.125 to 781.875 MHz U66 model: 782.125 to 805.875 MHz RF power output 10 mW (50-ohm load) Tone signal 32.768 kHz Battery condition signal 32.
Specifications Error Messages When a problem occurs, one of the following error messages may appear on the display. Standard frequency response 90° 0° dB 20 Message Contents Measures Error 11 An error occurred in backup memory data. The data was initialized. Set the transmitting channel and the input attenuation again. Error 21 The PLL synthesized circuit is in trouble. Contact your Sony dealer. Error 31 The battery voltage Use the specified battery. exceeds the allowable value.
Français Table des matières • Cet appareil est conçu pour être utilisé à une température ambiante allant de 0 à 50˚C (32 à 122˚F). • Ne placez pas cet appareil sur ou près d’une source de chaleur, telle qu’appareil d’éclairage, amplificateur de puissance, ou à un autre endroit en plein soleil ou soumis à une très forte humidité. A de tels endroits, la finition ou des composants internes risqueraient d’être endommagés.
Introduction Le WRT-807B est un microphone sans fil synthétisée UHF à utiliser dans un système de microphone sans fil synthétisé UHF à bande 800 MHz. Le WRT-807B fonctionne conjointement avec MB-806A avec le syntoniseur UHF à synthétiseur WRU-806B pour la concentration vocale. Le WRT-807B peut aussi être utilisé avec les systèmes de microphone sans fil Sony existants comprenant un émetteur synthétisé UHF WRT-805B/855B et un syntoniseur synthétisé UHF WRR-805B/855B/862B, etc.
Indication sur afficheur à cristaux liquides (ACL) de diverses informations L’ACL du microphone indique le numéro du canal actuel, la fréquence, le réglage d’atténuation d’entrée et la puissance restante de la pile. Le temps d’utilisation total de la pile est également indiqué (par incréments d’une minute) pour permettre de contrôler précisément l’usure de la pile.
Identification des pièces 1 Ecran antivent Protège contre le bruit provoqué par le vent. 1 2 8 2 Afficheur à cristaux liquides (ACL) A B C AF RF BATT 3 4 5 D Exemple d’affichage pour le modèle U68 A Indication AF (entrée audio) S’allume à la réception d’un signal audio plus puissant que le signal de référence. 7 B Indication RF (sortie d’antenne) S’allume pendant la transmission du signal de l’antenne. C Indication BATT (pile) Indique l’état de la pile.
D Indication CH (canal) Affiche le canal de transmission. A chaque pression du bouton SET en mode de transmission, l’indication de canal change comme suit. Canal de transmission Fréquence de transmission Niveau d’atténuation Temps d’utilisation total de la pile Pressez le bouton SET.
Identification des pièces 4 Témoin d’alimentation (POWER) S’allume quand le microphone est sous tension. 5 Interrupteur d’alimentation (POWER) Met le microphone sous/hors tension. Si vous mettez cet interrupteur sur ON sans maintenir un autre bouton enfoncé, le microphone passe en mode de transmission, et le signal du canal sélectionné est transmis. Le commutateur HOLD apparaît quand l’interrupteur POWER est réglé sur ON.
Alimentation Le microphone peut fonctionner en continu pendant environ 5 heures à 25˚C sur une pile alcaline LR6 (format AA). Indication d’état de la pile A la mise sous tension, l’état de la pile est indiquée par indication BATT sur l’afficheur à cristaux liquides. Insertion de la pile 1 e 2 E 1,3 1 Tournez la poignée dans le sens de la flèche pour ouvrir le logement de la pile. 2 Faites correspondre les marques de polarité de la pile avec celles du logement, et insérez-la dans le logement.
Réglages Passage au mode de réglage Mode de sélection de canal* Passez au mode de réglage pour changer de canal de transmission, de fréquence de transmission et de niveau d’atténuation, ou pour remettre l’indication du temps d’utilisation total de la pile à zéro. Mode de sélection de fréquence Mode d’ajustement de l’atténuateur Pour passer en mode de réglage Maintenez le bouton SET pressé et régler l’interrupteur POWER sur ON.
2 Appuyez sur le bouton + ou – pour sélectionner le numéro de canal (ou la fréquence). La pression du bouton + modifie cycliquement l’indication dans l’ordre indiqué dans les tableaux dans la “Liste des fréquences des systèmes de microphone sans fil Sony” séparée. La pression du bouton – fait parcourir cycliquement les indications en sens opposé.
Réglages Modification du réglage d’atténuation d’entrée Le réglage d’atténuation d’entrée peut être modifié sur la plage de 0 à 21 dB (par incréments de 3 dB) en mode de réglage ou de transmission. Modification de l’atténuation d’entrée en mode de réglage Mettez le microphone en mode de réglage. 3 Appuyez sur le bouton + ou – pour modifier le réglage d’atténuation. Si le niveau d’atténuation n’est pas affiché, appuyez sur le bouton SET jusqu’à ce qu’il apparaisse.
Remise à zéro de l’indication du temps d’utilisation total de la pile 4 Mettez l’interrupteur POWER sur OFF pour quitter le mode de réglage. Le temps d’utilisation total de la pile est le temps total (en heures et minutes) pendant lequel la pile a été utilisée. Il est enregistré quand le WRT-807B est sous tension. Remettez l’indication à 00:00 au remplacement de la pile. 1 2 Mettez le microphone en mode de réglage. 3 Appuyez sur le bouton –. L’indication est remise à 00:00.
Dépannage En cas de problème avec cet appareil, utilisez la liste de contrôle ci-dessous. Si le problème persiste, consultez votre revendeur Sony. Symptôme Signification/mesure à prendre Le microphone ne se met pas sous tension. • Les pôles + et – de la pile ne correspondent pas à ceux indiqués dans le logement de la pile. b Insérez la pile en respectant les polarités. • La pile est épuisée. b Remplacez-la par une neuve. • Les bornes + et – de la pile du microphone sont sales.
Symptôme Signification/mesure à prendre Son faible • Le niveau d’atténuation est réglé trop haut. b Le niveau de sortie est faible. Appuyez sur le bouton – en mode de réglage de niveau d’atténuation pour baisser le niveau d’atténuation. • Le volume sur l’amplificateur, le mixeur ou le syntoniseur est trop bas. b Ajustez le volume. Déformation du son • Le niveau d’atténuation est réglé trop bas. b Le niveau d’entrée est très haut.
Spécifications Section émetteur et modulateur Oscillateur Synthétiseur PLL piloté au cristal synthesizer Type d’émission F3E Fréquences porteuses Modèle CE57: 758,025 à 782,000 MHz Modèle CE62: 798,025 à 822,000 MHz Modèle CE67: 838,025 à 862,000 MHz Modèle U62: 758,125 à 781,875 MHz Modèle U66: 782,125 à 805,875 MHz Puissance de sortie RF 10 mW (charge de 50 ohms) Signal de tonalité 32,768 kHz Signal d’état de la pile 32,782 kHz Type d’antenne Filaire, longueur d’onde 1/4 Section audio Type de microphone P
Messages d’erreur En cas d’anomalie, l’un des messages suivants s’affiche. Réponse en fréquence standard 90° 0° dB 20 Message Signification Mesure à prendre Error 11 Une erreur est survenue au niveau des données de la mémoire de sauvegarde. Les données ont été initialisées. Réglez à nouveau le canal de transmission et l’atténuation d’entrée. Error 21 Problème dans le Contactez votre circuit PLL synthétisé. revendeur Sony. Error 31 La tension de la pile dépasse la valeur admissible.
Deutsch Inhaltsverzeichnis • Das Mikrofon ist für Umgebungstemperaturen zwischen 0 °C und 50 °C bestimmt. • Legen Sie das Mikrofon nicht in die Nähe von Wärmequellen wie Lampen oder Verstärkern und auch nicht an Plätze, die direktem Sonnenlicht oder Feuchtigkeit ausgesetzt sind, da sonst das Gehäuse in Mitleidenschaft gezogen und interne Teile beschädigt werden können.
Kurzbeschreibung Das drahtlose Mikrofon WRT-807B ist Bestandteil des 800MHz-UHF-Mikrofonsystems. Als Empfänger dient der MB-806A mit die UHFEmpfangseinheit WRU-806B für Sprachübertragung. POWER-Schalter mit Verriegelungsfunktion Der POWER-Schalter läßt sich in Einschaltstellung (ON) verriegeln, um ein versehentliches Ausschalten zu verhindern.
Speichern des Kanals und der Eingangssignaldämpfung Auch nach dem Ausschalten des Mikrofons und dem Herausnehmen der Batterie bleiben der eingestellte Kanal und die eingestellte Eingangssignaldämpfung gespeichert. Beim nächsten Einsatz des Mikrofons werden diese Einstellungen zurückgerufen. Hinweise zum Betrieb • Bei gleichzeitigem Betrieb von zwei oder mehr Mikrofonen sorgen Sie für einen Mindestabstand von 30 cm zueinander. • Sorgen Sie für einen Mindestabstand von 3 Metern zur Antenne des Tuners.
Bezeichnung der Teile 1 Windschutzkorb Schutz gegen Atem- und Windgeräusche. 1 2 8 2 Flüssigkristtaldisplay A B C AF RF BATT 3 4 5 D Anzeigebeispiel von Modell CE62 A AF-Anzeige Leuchtet auf, wenn der Toneingang über dem Referenzpegel liegt. 7 B RF-Anzeige Leuchtet auf, wenn ein Hochfrequenzsignal über die Antenne abgestrahlt wird. 6 4(DE) C BATT-Anzeige Zeigt den Batteriezustand an. Siehe „Batterieanzeigen“ auf Seite 7.
D CH-Anzeige Zeigt den Übertragungskanal an. Im normalen Sendebetrieb kann durch Drücken der SETTaste die Anzeige wie folgt zyklisch weitergeschaltet werden. Siehe auch „Ändern des Übertragungskanals“ auf Seite 8, „Ändern der Eingangssignaldämpfung“ auf Seite 10 und „Zurücksetzen der akkumulierten Betriebszeit“ auf Seite 11. 3 SET-Taste Im normalen Sendebetrieb kann durch Drücken dieser Taste die in der unteren Hälfte des Flüssigkristalldisplays angezeigte Information umgeschaltet werden.
Bezeichnung der Teile 4 POWER-Anzeige Leuchtet bei eingeschaltetem Mikrofon. 6 Antenne 5 POWER-Schalter Zum Einschalten (ON) und Ausschalten (OFF) des Mikrofons. Wenn dieser Schalter auf ON gestellt wird, ohne gleichzeitig eine andere Taste zu drücken, schaltet das Mikrofon auf Sendebetrieb und überträgt das Signal auf dem gewählten Kanal. In Stellung ON wird der HOLD-Schalter sichtbar.
Stromversorgung Das Mikrofon wird durch eine Alkali-Mignonzelle (LR6, Größe AA) versorgt. Bei 25 ºC ist ein durchgehender Betrieb von ca. 5 Stunden möglich. Batterieanzeigen Nach dem Einschalten wird im Flüssigkristalldisplay unter BATT der Batteriezustand angezeigt. Einlegen der Batterie 1 BATTAnzeige Batteriezustand e Leuchtet Gut 2 3 4 Leuchtet Blinkt Erloschen Weniger als die Hälfte Fast leer Ganz leer 2 E 1,3 1 Drehen Sie den Griff in Pfeilrichtung, um das Batteriefach zu öffnen.
Einstellungen Einstellmodus Kanalwahl* Im Einstellmodus können Sie vor dem Betrieb den Übertragungskanal und den Dämpfungspegel ändern oder die akkumulierte Batteriebetriebszeit zurücksetzen. Frequenzwahl Dämpfungseinstellung So schalten Sie den Einstellmodus ein Halten Sie die SET-Taste gedrückt, und schalten Sie gleichzeitig den POWER-Schalter auf ON. Halten Sie die SET-Taste weiter gedrückt, bis die gewünschte Anzeige im Flüssigkristalldisplay erscheint.
2 Wählen Sie durch Drücken der Taste + oder – die gewünschte Kanalnummer (oder Frequenz). Durch Drücken der Taste + wird zyklisch wie in den Tabellen del separaten „Frequenzliste für UHFMikrofonsystem“ weitergeschaltet. Mit der Taste – erfolgt die Wahl in umgekehrter Richtung. Kanalwahl Taste + Frequenzwahl Taste – Taste + Taste – Anzeigebeispiel von Modell CE62 Wenn eine der Tasten gedrückt gehalten wird, erfolgt rasche Weiterschaltung von Kanalnummer (oder Frequenz).
Einstellungen Ändern der Eingangssignaldämpfung Die Eingangssignaldämpfung kann in 3-dB-Schritten von 0 bis 21 dB verändert werden. Dies ist sowohl im Einstellmodus als auch im normalen Sendebetrieb möglich. Im Einstellmodus 4 Sobald der gewünschte Dämpfungspege erscheint, stellen Sie den POWER-Schalter auf OFF, um den Einstellvorgang zu beenden, oder drücken Sie die SETTaste, um weitere Einstellungen vorzunehmen.
Während „00:00“ angezeigt wird, können Sie durch Drücken der Taste + dir ursprüngliche Anzeige zurückrufen. Zurücksetzen der akkumulierten Betriebszeit Nach jedem Batteriewechsel sollte die im Flüssigkristalldisplay (in Stunden und Minuten) angezeigte akkumulierte Betriebszeit des WRT-807B auf „00:00“ zurückgesetzt werden. Die akkumulierte Betriebszeit liefert dann eine Aussage darüber, wie lange die Batterie schon verwendet wurde. 1 2 Schalten Sie das Mikrofon in den Einstellmodus.
Störungssuche Bei Störungen und Problemen versuchen Sie diese bitte anhand der folgenden Liste zu beheben, bevor Sie sich an ihren SonyFachhändler wenden. Symptom Bedeutung/Abhilfe Das Mikrofon läßt sich nicht einschalten. • Die Batterie wurde falsch herum eingelegt. b Legen Sie die Batterie so ein, daß ihre Polung mit der im Batteriefach angezeigten Polung übereinstimmt. • Die Batterie ist erschöpft. b Legen Sie eine frische Batterie ein. • Die Batteriekontakte im Batteriefach sind verschmutzt.
Symptom Bedeutung/Abhilfe Schwacher Ton. • Es ist ein zu hoher Dämpfungspegel eingestellt. b Der Ausgangspegel ist niedrig. Drücken Sie im Dämpfungspegel-Einstellmodus die Taste –, um den Dämpfungspegel zu senken. • An Verstärker, Mischpult oder Tuner ist eine zu geringe Lautstärke eingestellt. b Stellen Sie eine höhere Lautstärke ein. Verzerrter Ton. Es ist ein zu niedriger Dämpfungspegel eingestellt. b Der Ausgangspegel ist viel zu hoch.
Technische Daten Sender und Modulator Oszillator Quarzgesteuerter PLLSynthesizer Modulationsart F3E Trägerfrequenzen Modell CE57: 758,025 bis 782,000 MHz Modell CE62: 798,025 bis 822,000 MHz Modell CE67: 838,025 bis 862,000 MHz Modell U62: 758,125 bis 781,875 MHz Modell U66: 782,125 bis 805,875 MHz RF-Ausgangsleistung 10 mW (Ausgangsimpedanz 50 Ohm) Pilottonsignal 32,768 kHz Batteriezustandsignal 32,782 kHz Antennentyp 1/4 Wellenlänge, Drahtantenne Audio Mikrofontyp Preemphasis Hub Frequenzgang Signal-Rausc
Fehlermeldungen Bei Störungen und Problemen erscheinen die folgenden Meldungen im Display. Standard-Frequenzgang 90° 0° dB 20 Meldung Bedeutung Maßnahmen Error 11 Fehler in den Speicherdaten. Die Daten wurden zurückgesetzt. Den Übertragungskanal und die Eingangssignaldämpfung erneut einstellen. Error 21 Störung in der PLLBenachrichtigen Sie Synthesizerschaltung. Ihren Sony-Fachhändler. Error 31 Falsche Batteriespannung. Error 41 Störung eines internen Schaltkreises.
Español Índice • La unidad ha sido diseñada para emplearse dentro de un entorno de temperaturas ambientes de 0ºC a 50ºC (32ºF a 122ºF). • No coloque la unidad en o cerca de fuentes de calor tales como lámparas amplificadores de potencia o en un lugar expuesto a los rayos del sol o humedad excesivo. Estos lugares pueden afectar la terminación exterior o las piezas en el interior de la unidad.
Introducción El WRT-807B es un micrófono inalámbrico con sintetización UHF para utilizar en la banda de 800 MHz para sistemas de micrófono inalámbrico con sintetización UHF. El WRT-807B se utiliza en combinación con el MB-806A con el sintonizador sintetizado UHF WRU-806B para concentrar la voz. El WRT-807B también puede utilizarse con los sistemas de micrófono inalámbricos de Sony compuestos por el transmisor sintetizado de UHF WRT-805B/855B y el sintonizador sintetizado de UHF WRR-805B/855B/862B, etc.
Visualización de cristal líquido para variada información El visualizador de cristal líquido del micrófono mostrará el número del canal actual, la frecuencia, ajuste de atenuación de entrada y carga residual de la pila. Se indica también el tiempo de uso acumulado de la pila (en incrementos de un minuto) para un control preciso del uso de la pila.
Identificación de piezas 1 Pantalla contra el viento Protege contra el ruido provocado por el viento. 1 2 8 2 Visualizador de cristal líquido A B C AF RF BATT 3 4 5 D Ejemplo de visualización para el modelo CE62 A Indicación de entrada de audio (AF) Se enciende cada vez que se recibe una señal de audio más fuerte que el nivel de referencia. 7 B Indicación de salida de antena (RF) Se enciende durante la transmisión de una señal a través de la antena.
D Indicación de canal (CH) Muestra el canal de transmisión. Cada vez que presione la tecla SET en el modo de transmisión, la indicación de canal cambiará de la siguiente forma. Canal de transmisión Frecuencia de transmisión Nivel de atenuación Tiempo de uso acumulado de la pila Presione la tecla SET.
Identificación de piezas 4 Indicador POWER Se enciende cuando se está utilizando el micrófono. 5 Interruptor de alimentación (POWER) Utilícelo para conectar y desconectar el micrófono. Cuando ponga este interruptor en ON sin mantener presionada ninguna otra tecla, el micrófono pasará al modo de transmisión y se transmitirá la señal del canal seleccionado. Aparece el interruptor HOLD cuando el interruptor POWER está en ON.
Fuente de alimentación El micrófono puede funcionar con una pila alcalina LR6 (tamaño AA) durante unas 5 horas continuas a 25ºC (77ºF). Indicación de pila Cuando conecte la alimentación, en la indicación BATT del visualizador de cristal líquido aparecerá el estado de la pila.
Ajustes Activación del modo de ajuste Modo de selección de canal* En el modo de ajuste podrá cambiar el canal de transmisión y el nivel de atenuación o reponer la indicación de tiempo de uso acumulado de la pila. Modo de selección de frecuencia Modo de ajuste de atenuador Para entrar en el modo de ajuste Mantenga presionada la tecla SET y ponga el interruptor POWER en ON. Mantenga presionada la tecla SET hasta que en el visualizador aparezca una indicación.
2 Presione la tecla + o – para seleccionar el número de canal (o frecuencia). Al presionar la tecla + la indicación cambiará cíclicamente en el orden mostrado en la tabla “Lista de frequencias del sustema de micrófono inalámbrico de Sony” por separado. Cada vez que presione la tecla – cambiará en el orden inverso.
Ajustes Cambio del ajuste de atenuación de entrada Se podrá cambiar el ajuste de la atenuación de entrada dentro de un margen de 0 dB a 21 dB (en pasos de 3 dB) en el modo de ajuste o en el modo de transmisión. Cambio de la atenuación de entrada en el modo de ajuste 4 Cuando visualice el nivel deseado, ponga el interruptor POWER en OFF para salir el modo de ajuste o presione la tecla SET para continuar las operaciones en el modo de ajuste.
Reposición de la indicación de tiempo de uso acumulado de la pila 4 Ponga el interruptor POWER en OFF para salir del modo de ajuste. La indicación de tiempo de uso acumulado de la pila es el tiempo total (en horas y minutos) de utilización de la pila. Se registra siempre que el WRT-807B esté conectado. Reponga la indicación a 00:00 cada vez que reemplace la pila. 1 2 Ponga el micrófono en el modo de ajuste. 3 Presione la tecla –. La indicación se repone a 00:00.
Localización de averías Si tiene problemas para el uso de este aparato, recurra a la siguiente lista de comprobación. Si no puede solucionar el problema, consulte con su proveedor de Sony. Síntoma Significado/Solución El micrófono no se conecta. • Los polos + y – de la pila no coinciden con los dibujados en el portapila. b Coloque la pila con las polaridades en el sentido correcto. • La pila está gastada. b Cambie la pila por otra nueva. • Los terminales de pila en el micrófono están sucios.
Síntoma Significado/Solución El sonido se escucha bajo. • El nivel de atenuación está demasiado alto. b El nivel de salida está bajo. Presione la tecla – en el modo de ajuste de nivel de atenuación para bajar el nivel de la atenuación. • El volumen del amplificador, mezclador o sintonizador está bajo. b Ajuste el volumen. Hay distorsión en el sonido. El ajuste de nivel de atenuación está demasiado bajo. b El nivel de entrada está muy alto.
Especificaciones Sección del transmisor y modulador Oscilador Sintonizador de PLL controlado por cristal Tipo de transmisión F3E Frecuencias portadoras Modelo CE57: 758,025 a 782.
Mensajes de error Cuando ocurra un problema, es posible que en el visualizador aparezca uno de los mensajes de error siguientes. Respuesta de frecuencia estándar 90° 0° dB 20 180° Mensajes Contenido Medidas Error 11 Se ha producido un error en los datos de la memoria de respaldo. Los datos se han inicializado. Vuelva a ajustar el canal de transmisión y la atenuación de entrada. Error 21 El circuito sintetizado Póngase en contacto con de bucle de enganche su proveedor Sony. de fase está averiado.
Sony Corporation Printed in Japan