Sony Corporation
3-860-143-15(1) Personal Component System Operating Instructions page 2EN EN Bedienungsanleitung Seite 2D D PMC-205L 1997 by Sony Corporation
Warning CAUTION To prevent fire or shock hazard, do not expose the player to rain or moisture. You can use this player on AC power source only. You cannot use it on batteries. When you use this player for the first time, or when you have not used it for a long time, leave it connected to AC power source for about one hour to charge the built-in backup battery for the clock, timer, preset radio stations, etc. You can use the player during charging.
Table of contents Basic Operations Basic Operations 4 Playing a CD 6 Listening to the radio 8 Playing a tape 10 Recording on a tape The CD Player 12 Using the display 13 Locating a specific track 14 Playing tracks repeatedly (Repeat Play) 15 Creating your own program (Program Play) The Radio 17 Presetting radio stations 18 Playing preset radio stations Setting Up 23 Hooking up the system 27 Selecting the audio emphasis (Sound Mode/MEGA BASS) EN Additional Information 28 30 33 34 35 Precautions
Basic Operations Playing a CD 3 1,2 For hookup instructions, see pages 23 - 26. 1 Press 6 OPEN/CLOSE down to open the disc compartment and place the CD on the CD compartment. With the label side up 2 3 Close the lid of the CD compartment. Press ( (direct power-on). The player plays all the tracks once.
Use these buttons for additional operations OPERATE P p VOLUME +/– Basic Operations 6 OPEN/CLOSE =/+ Tip Next time you want to listen to a CD, just press (. The player turns on automatically and starts playing the CD. To Press Adjust the volume VOLUME +/– Stop playback p Pause playback P Press again to resume play after pause.
Listening to the radio 1 2 For hookup instructions, see pages 23 - 26. 1 2 Press BAND until the band you want appears in the display (direct power-on). Hold down TUNE +/– until the frequency digits begin to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button once at a time. 6EN Basic Operations Display Indicates an FM stereo broadcast.
Use these buttons for additional operations OPERATE Basic Operations VOLUME +/– PLAY MODE MONO/ST/ISS Tips • If the FM broadcast is noisy, press PLAY MODE/MONO/ST/ISS on the player until “Mono” appears in the display and the radio will play in monaural. • Next time you want to listen to the radio, just press BAND. The player turns on automatically and starts playing the previous station.
Playing a tape 2 1 For hookup instructions, see pages 23 - 26. 1 Press p6 to open the tape compartment and insert a recorded tape. Use TYPE I (normal) tape only. Close the compartment. With the side you want to play facing forward 2 Press (. The player turns on (direct power-on) and starts playing.
Use these buttons for additional operations OPERATE 0/) VOLUME +/– Basic Operations p6 P Tip Next time you want to listen to a tape, just press (. The player turns on automatically and starts playing the tape. To Press Adjust the volume VOLUME +/– Stop playback p6 Pause playback P Press the button again to resume play after pause.
Recording on a tape 3 1 For hookup instructions, see pages 23 - 26. 1 Press p6 to open the tape compartment and insert a blank tape. Use TYPE I (normal) tape only. With the side you want to record on facing forward 2 Select the program source you want to record. To record from the CD player, insert a CD (see page 4) and press p on the CD section. To record from the radio, press BAND and tune in the station you want (see page 6.) 3 10EN Basic Operations Press r to start recording.
Use these buttons for additional operations OPERATE p6 P Basic Operations Tips • Adjusting the volume or the audio emphasis (see page 27) will not affect the recording level. • If the MW/LW radio makes a whistling sound after you’ve pressed r in step 3, press PLAY MODE/ MONO/ST/ISS to select the position that most decreases the noise. • To erase a recording, proceed as follows: 1 Turn on the power and press FUNCTION until “TAPE”appears in the display. 2 Press r.
The CD Player Using the display You can check information about the CD using the display. DISPLAY/ ENTER Checking the total track number and playing time Press DISPLAY/ENTER in stop mode. If the CD has more than 10 tracks, “OVER 10” appears in the display. Total playing time Total track number Music calendar Checking the remaining time Press DISPLAY/ENTER while playing a CD. The track numbers in the music calendar disappear after they are played.
Locating a specific track Number buttons The CD Player You can quickly locate any track using the number buttons. You can also find a specific point in a track while playing a CD. 0/–, )/+ Note You cannot locate a specific track if “PGM” or “SHUF REP” is lit in the display. Turn off the indication by pressing p on the CD section. Tip When you locate a track numbered over 10, press > 10 first, then the corresponding number buttons. Example: To play track number 23, press >10 first, then 2 and 3.
Playing tracks repeatedly (Repeat Play) Number buttons You can play tracks repeatedly in normal, shuffle or program play modes (see pages 15 and 16.) MODE ( p Note When you repeat a single track or all the tracks, make sure neither “PGM” nor “SHUF REP” is lit in the display. If either is lit, turn it off by pressing p on the CD section. 1 Press p. “Cd” appears in the display. 2 3 Press MODE until the repeat mode you want appears in the display.
Creating your own program (Program Play) MODE ( The CD Player Number buttons You can make a program of up to 20 tracks in the order you want them to be played. p Tips • To create your own program on the player by selecting the track you want while listening to the CD, proceed as follows: 1 Press ( to start play. 2 Press PGM SET/ AUTO PRESET . “PGM” flashes in the display. 3 Press =/+ to select the track you want to program, and press DISPLAY/ ENTER/MEM. Repeat this step. 4 Press p.
Creating your own program (Program Play) (continued) Tips • You can play the same program again, since the program is saved until you open the CD compartment. • You can record your own program. After you’ve created the program, insert a blank tape into the tape compartment and press r on the player to start recording. 16EN The CD Player To cancel Program Play Press MODE until “PGM” disappears in the display. To check the order of tracks before play Press + on the player.
The Radio Presetting radio stations PGM SET/AUTO PRESET BAND The Radio You can store radio stations into the player's memory. You can preset up to 30 radio stations, 10 for each band in any order. 1 Press BAND until the band you want appears in the display. 2 Press PGM SET/AUTO PRESET until “AUTO ” appears. The stations are stored in memory from the lower frequencies unless a station has a weak signal.
Playing preset radio stations Once you've preset the stations, use the number buttons to tune in your favorite stations. Number buttons BAND Tip You can tune in a preset station with the player. Use PRESET +/– instead of the number buttons. 18EN The Radio 1 2 Press BAND to select the band. Press the number buttons to tune in a stored station.
The Timer Setting the clock “0:00” indication appears in the display until you set the clock. As long as the clock goes, “:” flashes. DISPLAY/ ENTER 0/–, )/+ Tip The time display system: 24-hour system The Timer TIMER/ CLOCK Before you begin, hook up the systems (see page 23.) 1 Press and hold TIMER/CLOCK for about 2 seconds until the hour digit flash. 2 Set the clock. 1 Press 0/– or )/+ to set the hour and press DISPLAY/ ENTER. . 2 Press 0/– or )/+ to set the minutes. 3 Press DISPLAY/ENTER.
Waking up to music STANDBY You can wake up to music or a radio program at a preset time. Make sure you have set the clock (“Setting the clock” on page 19). TIMER/ CLOCK DISPLAY/ ENTER 0/–, )/+ Before you begin, make sure the t (clock) indication is not lit in the display. If it is lit, press STANDBY. 1 Prepare the music source you want to play. Source 2 Do this CD Insert a CD. RADIO Tune in a station. Press TIMER/CLOCK to display the t indication.
Tips • The display window does not light while the waking up timer is operating even if the power is on. • You can have the player go on the next day at the same time. Just press STANDBY until the t indication appears in the display. The preset settings remain until you reset them. 5 6 Note The timer mode is cancelled: – when you press ( while music plays in the timer mode. – when you select “TAPE” using FUNCTION on the remote.
Falling asleep to music SLEEP You can set the player to turn off automatically after 10, 20, 30, 60, 90 and 120 minutes, allowing you to fall asleep while listening to music. Tips • The display window does not light while the sleep timer is on. • You can combine the waking up timer with the sleeping timer. Set the waking up timer first (see page 20), turn on the power, and then set the sleep timer. • You can prepare the different music for the waking up timer and the sleeping timer.
Setting Up Hooking up the system 2 MW/LW loop aeral Make sure you turn off the power before making any connections. 2 FM aerial 1 Audio connecting cord Setting Up Right speaker Left speaker 1 Speaker cord 1 Power cord To a wall outlet 3 AC power cord Note Connect the right speaker for this unit only to the speaker terminals of the left speaker. If you connect any other speaker or equipment, malfunction may occur.
Hooking up the system (continued) 2 Connect the audio connecting cord (supplied) to the SIGNAL OUTPUT jacks of the player and the SIGNAL INPUT jacks of the left speaker. Connect the white plugs to the L (left) jacks and the red plugs to the R (right) jacks. 3 Connect the speaker cord of the right speaker to the SPEAKER OUT terminals of the left speaker. Connect the red wire to the (+) plus terminal, and the black wire to the (–) minus terminal.
Note Keep the aerials away as far as possible from the speaker cords and other connecting cords. If you do not, noise may be heard. 2 Hooking up the aerials MW/LW loop aerial* (supplied) Setting Up FM aerial** (supplied) *Reorient the aerial to improve broadcast reception. **Keep the aerial as horizontal as possible. Setting up the MW/LW loop aerial Tip The sound quality may be changed depending on the polarity of the plug. Change the direction of inserting the plug and check the sound quality.
Hooking up the system (continued) 4 Inserting batteries into the remote Insert two R6 (size AA) batteries (not supplied) Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. To improve the FM reception Disconnect the supplied FM aerial and connect the FM outdoor aerial (not supplied). If you use a distributor, you can also use the TV aerial.
Selecting the audio emphasis SOUND (Sound Mode/MEGA BASS) You can adjust the audio emphasis of the sound you are listening to. Setting Up Selecting the sound characteristic Press SOUND to select the audio emphasis you want. Choose To get powerful, clean sounds, emphasizing low and high range audio “MEGA BASS” appears in the display.
Additional Information Precautions On safety • As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components.
Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. Notes on cassettes • Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. Side A • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs.
Troubleshooting Remedy There is no audio. • Press OPERATE to turn on the player. • Connect the AC power cord to a wall outlet securely. • Connect the power cord to the POWER IN of the player (page 23). • Connect the audio connecting cord correctly (page 24.) • Adjust the volume. • Unplug the headphones when listening through speakers. “no disc“ lights in the display even when a CD is in place. • Insert the CD with the label surface up. The CD does not play. • • • • The sound drops out.
Tape Player Timer Symptom Remedy The tape does not move when you press an operation button. • Close the cassette compartment securely. The REC r button does not function/The tape does not play. • Make sure the safety tab on the cassette is in place. • Press FUNCTION to switch the function of the player to “TAPE”. The tape does not erase completely. • Clean the erasing heads (see page 33.) The tape does not record. • Make sure the tape is inserted properly.
Troubleshooting (continued) Remedy The remote does not function. • Replace all the batteries in the remote with new ones if they are weak. • Make sure that you are pointing the remote at the remote sensor on the player. • Remove any obstacles in the path of the remote and the player. • Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. • Move closer to the player when using the remote.
Maintenance Cleaning the lens If the lens becomes dirty, it may cause a skipping of sound during CD operation. Clean with a commercially available blower. Cleaning the tape heads and tape path Wipe the heads, the pinch rollers and the capstans with a cleaning swab slightly moistened with cleaning fluid or alcohol after every 10 hours of operation for optimum playback and recording quality.
Specifications CD player section General System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length:780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20,000 Hz +1/–2.
Index A I, J, K S Audio emphasis 27 Selecting AUTO PRESET 17 Improving broadcast reception 7 B L Batteries for remote 26 tracks 5, 13 Listening to the radio 6 Locating a specific track 13 C CD player 12 Cleaning cabinet 33 tape heads and tape path 33 Setting the clock 19 Setting up 23 Sound mode 27 M, N, O T MEGA BASS 27 Timer P, Q Falling asleep to music 22 Playing Waking up to music 20 Connecting a CD 4 AC power cord 25 Troubleshooting 30 a tape 8 the system.
Achtung VORSICHT Um Feuergefahr und die Gefahr eines elektrischen Schlags zu vermeiden, setzen Sie das Gerät weder Regen noch sonstiger Feuchtigkeit aus. Sie können dieses Gerät nur mit Netzstrom betreiben. Sie können es nicht mit Batterien betreiben.
Inhalt Grundfunktionen Grundfunktionen 4 Wiedergeben einer CD 6 Radiobetrieb 8 Wiedergeben einer Kassette 10 Aufnehmen auf eine Kassette Der CD-Player 12 Das Display 13 Ansteuern eines bestimmten Titels 14 Wiederholtes Wiedergeben von Titeln (Repeat Play) 15 Zusammenstellen eines eigenen Programms (Program Play) Das Radio Vorbereitungen 23 Anschließen des Systems 27 Auswählen der Klangbetonung (Klangmodus/MEGA BASS) D Weitere Informationen 28 30 33 34 35 Sicherheitsmaßnahmen Störungsbehebung War
Grundfunktionen Wiedergeben einer CD 3 1,2 Informationen zum Anschließen des Systems finden Sie auf Seite 23 - 26. 1 Öffnen Sie mit 6 OPEN/CLOSE das CD-Fach, und legen Sie die CD in das CD-Fach ein. Mit der beschrifteten Seite nach oben 2 3 Schließen Sie den Deckel des CDFachs. Drücken Sie ( (Direkteinschaltfunktion). Der CD-Player gibt alle Titel einmal wieder.
Folgende Tasten stehen für weitere Funktionen zur Verfügung: P p 6 OPEN/CLOSE VOLUME +/– Grundfunktionen OPERATE =/+ Tip Wenn Sie das nächste Mal eine CD hören wollen, drücken Sie einfach (. Das Gerät schaltet sich automatisch ein und beginnt die Wiedergabe der CD. Zum Drücken Sie Einstellen der Lautstärke VOLUME +/– Beenden der Wiedergabe p Unterbrechen der Wiedergabe P Drücken Sie die Taste erneut, um die Wiedergabe nach einer Pause fortzusetzen.
Radiobetrieb 1 2 Informationen zum Anschließen des Systems finden Sie auf Seite 23 - 26. 1 2 Drücken Sie BAND, bis der gewünschte Frequenzbereich im Display angezeigt wird (Direkteinschaltfunktion). Display Halten Sie TUNE +/– gedrückt, bis die Ziffern der Frequenzangabe im Display durchzulaufen beginnen. Zeigt an, daß es sich um einen UKWStereosender handelt.
Folgende Tasten stehen für weitere Funktionen zur Verfügung: VOLUME +/– Grundfunktionen OPERATE PLAY MODE MONO/ST/ISS Tips • Wenn beim UKWEmpfang Störgeräusche auftreten, drücken Sie PLAY MODE/MONO/ ST/ISS am Gerät, bis “Mono” im Display erscheint. Der Radioempfang ist in diesem Fall monaural. • Wenn Sie das nächste Mal Radio hören wollen, drücken Sie einfach BAND. Das Gerät schaltet sich automatisch ein, und der zuvor eingestellte Sender ist zu hören.
Wiedergeben einer Kassette 2 1 Informationen zum Anschließen des Systems finden Sie auf Seite 23 - 26. 1 Öffnen Sie mit p6 das Kassettenfach, und legen Sie eine bespielte Kassette ein. Verwenden Sie nur Kassetten des Typs TYPE I (normal). Schließen Sie das Kassettenfach. Mit der wiederzugebenden Seite nach vorne 2 Drücken Sie (. Das Gerät schaltet sich ein (Direkteinschaltfunktion) und startet die Wiedergabe.
Folgende Tasten stehen für weitere Funktionen zur Verfügung: 0/) p6 VOLUME +/– Grundfunktionen OPERATE P Tip Wenn Sie das nächste Mal eine Kassette abspielen wollen, drücken Sie einfach (. Das Gerät schaltet sich automatisch ein und startet die Wiedergabe der Kassette. Zum Drücken Sie Einstellen der Lautstärke VOLUME +/– Beenden der Wiedergabe p6 die Wiedergabe zu unterbrechen P Drücken Sie die Taste erneut, um die Wiedergabe nach einer Pause wiederaufzunehmen.
Aufnehmen auf eine Kassette 3 1 Informationen zum Anschließen des Systems finden Sie auf Seite 23 - 26. 1 Öffnen Sie mit p6 das Kassettenfach, und legen Sie eine leere Kassette ein. Verwenden Sie nur Kassetten des Typs TYPE I (normal). Mit der Seite, auf die aufgenommen werden soll, nach vorne 2 Wählen Sie die aufzunehmende Tonquelle. Um vom CD-Player aufzunehmen, legen Sie eine CD ein (siehe Seite 4) und drücken p am CD-Player.
3 Folgende Tasten stehen für weitere Funktionen zur Verfügung: OPERATE p6 P Zum Drücken Sie Beenden der Aufnahme p6 Unterbrechen der Aufnahme P Drücken Sie diese Taste erneut, um die Aufnahme fortzusetzen. Ein-/Ausschalten des Geräts OPERATE Grundfunktionen Grundfunktionen Tips • Das Einstellen der Lautstärke oder der Klangbetonung (siehe Seite 27) beeinflußt den Aufnahmepegel nicht.
Der CD-Player Das Display Im Display können Sie Informationen zur CD anzeigen lassen. DISPLAY/ ENTER Anzeigen der Gesamtzahl der Titel und der Gesamtspieldauer Drücken Sie im Stopmodus DISPLAY/ENTER. Sind auf der CD mehr als 10 Titel vorhanden, erscheint “OVER 10” im Display. Gesamtspieldauer Gesamtzahl der Titel Musikkalender Anzeigen der Restspieldauer Drücken Sie DISPLAY/ENTER während der Wiedergabe einer CD.
Ansteuern eines bestimmten Titels Zahlentasten Der CD-Player Mit Hilfe der Zahlentasten können Sie mühelos jeden beliebigen Titel direkt ansteuern. Darüber hinaus können Sie während der Wiedergabe einer CD eine bestimmte Passage innerhalb eines Titels suchen. 0/–, )/+ Hinweis Sie können einen bestimmten Titel nicht ansteuern, wenn “PGM” oder “SHUF REP” im Display leuchtet. Schalten Sie die Anzeige aus, indem Sie p im CD-Feld drücken.
Wiederholtes Wiedergeben von Titeln (Repeat Play) Zahlentasten Sie können die Titel auf einer CD mehrmals wiedergeben lassen, und zwar wahlweise in der normalen Reihenfolge (Normal Play), in willkürlicher Reihenfolge (Shuffle Play) oder in einer vorher festgelegten Reihenfolge (Program Play) (siehe auf Seite 15 - 16). Hinweis Wenn Sie einen einzelnen Titel oder alle Titel wiederholt wiedergeben möchten, achten Sie darauf, daß weder “PGM” noch “SHUF REP” im Display leuchtet.
Zusammenstellen eines eigenen Programms (Program Play) Sie können bis zu 20 Titel in beliebiger Reihenfolge zu einem individuellen Programm zusammenstellen und wiedergeben lassen. Der CD-Player Zahlentasten MODE ( p Tips • Wenn Sie ein eigenes Programm zusammenstellen wollen, indem Sie während der CD-Wiedergabe die Titel auswählen, gehen Sie folgendermaßen vor: 1 Starten Sie mit ( die Wiedergabe. 2 Drücken Sie PGM SET/ AUTO PRESET. “PGM” blinkt im Display.
Zusammenstellen eines eigenen Programms (Program Play) (Fortsetzung) Tips • Sie können dasselbe Programm nochmals abspielen, da das Programm gespeichert bleibt, bis Sie das CDFach öffnen. • Sie können Ihr eigenes Programm aufnehmen. Legen Sie nach dem Zusammenstellen des Programms eine leere Kassette in das Kassettenfach ein, und starten die Aufnahme mit r am Gerät. 16D Der CD-Player So brechen Sie Program Play ab Drücken Sie MODE, bis “PGM” nicht mehr im Display angezeigt wird.
Das Radio Speichern von Radiosendern PGM SET/AUTO PRESET BAND Das Radio Sie können bis zu 30 Radiosender, 10 pro Frequenzbereich, in beliebiger Reihenfolge voreinstellen und im Speicher des Geräts abspeichern. 1 Drücken Sie BAND, bis der gewünschte Frequenzbereich im Display erscheint. 2 Drücken Sie PGM SET/AUTO PRESET, bis “AUTO” erscheint. Die Sender werden in numerischer Reihenfolge, beginnend mit der niedrigsten Frequenz, gespeichert, sofern sie in ausreichender Signalstärke empfangen werden.
Wiedergeben gespeicherter Radiosender Wenn Sie die Radiosender gespeichert haben, können Sie sie mit Hilfe der Zahlentasten mühelos abrufen. Zahlentasten BAND Tip Sie können einen gespeicherten Sender auch mit den Tasten am Gerät einstellen. Verwenden Sie dazu PRESET +/– anstelle der Zahlentasten. 18D Das Radio 1 2 Wählen Sie mit BAND den Frequenzbereich. Stellen Sie mit den Zahlentasten einen gespeicherten Sender ein.
Der Timer Einstellen der Uhr Die Anzeige “0:00” erscheint im Display, bis Sie die Uhr einstellen. Wenn die Uhr läuft, blinkt “:” im Display. DISPLAY/ ENTER 0/–, )/+ Tip Die Uhrzeit wird im folgenden Format angezeigt: 24-Stunden-Format Der Timer TIMER/ CLOCK Schließen Sie zunächst alle Geräte an (siehe Seite 23). 1 Halten Sie TIMER/CLOCK etwa 2 Sekunden lang gedrückt, bis die Stundenangabe blinkt. 2 Stellen Sie die Uhrzeit ein.
Aufwachen mit Musik STANDBY Sie können sich zu einer bestimmten Zeit mit Musik wecken lassen. Dazu muß die Uhr eingestellt sein (siehe “Einstellen der Uhr” auf Seite 19). TIMER/ CLOCK DISPLAY/ ENTER 0/–, )/+ Sorgen Sie zunächst dafür, daß die Anzeige t (Uhrzeit) nicht im Display leuchtet. Andernfalls drücken Sie STANDBY. 1 Bereiten Sie die wiederzugebende Musikquelle vor. Musikquelle 2 Gehen Sie folgendermaßen vor: CD Legen Sie eine CD ein. RADIO Stellen Sie einen Sender ein.
Tips • Das Display leuchtet nicht, solange der Weck-Timer in Betrieb ist, auch wenn das Gerät eingeschaltet ist. • Sie können das Gerät so einstellen, daß es sich am nächsten Tag zur selben Zeit einschaltet. Drücken Sie einfach STANDBY, bis die Anzeige t im Display erscheint. Die Einstellungen bleiben im Gerät gespeichert, bis Sie sie ändern. 5 Hinweis Der Timer-Modus wird aufgehoben: – wenn Sie am Bedienfeld für den Kassettenrecorder die Taste ( drücken, während die Wiedergabe im Timer-Modus läuft.
Einschlafen mit Musik SLEEP Sie können das Gerät so einstellen, daß es sich automatisch nach 10, 20, 30, 60, 90 oder 120 Minuten ausschaltet. Auf diese Weise können Sie beim Einschlafen Musik hören. Tips • Die Anzeige im Display ist abgeschwächt, während der SleepTimer aktiviert ist. • Sie können den WeckTimer mit dem SleepTimer kombinieren. Stellen Sie dazu zuerst den Weck-Timer ein (siehe Seite 20), schalten Sie dann das Gerät ein, und stellen Sie den Sleep-Timer ein.
Vorbereitungen Anschließen des Systems 2 MW/LW-Ringantenne 2 UKW-Antenne 1 Audioverbindungskabel Achten Sie darauf, daß das Gerät ausgeschaltet ist, bevor Sie irgendwelche Anschlüsse vornehmen. Linker Lautsprecher 1 Lautsprecherkabel 1 Netzkabel 3 Netzkabel Hinweise Schließen Sie ausschließlich den rechten Lautsprecher für dieses Gerät an die Lautsprecheranschlüsse des linken Lautsprechers an. Wenn Sie einen anderen Lautsprecher oder ein Gerät daran anschließen, kann es zu Fehlfunktionen kommen.
Anschließen des Systems (Fortsetzung) 2 Schließen Sie das Audioverbindungskabel (mitgeliefert) an die Buchsen SIGNAL OUTPUT des Geräts und an die Buchsen SIGNAL INPUT des linken Lautsprechers an. Schließen Sie die weißen Stecker an die Buchsen L (links) und die roten Stecker an die Buchsen R (rechts) an. 3 Schließen Sie das Lautsprecherkabel des rechten Lautsprechers an die Anschlüsse SPEAKER OUT des linken Lautsprechers an.
Hinweis Halten Sie die Antennen so weit wie möglich von den Lautsprecher- und sonstigen Verbindungskabeln fern. Andernfalls können Störgeräusche zu hören sein. 2 Anschließen der Antennen MW/LW-Ringantenne* (mitgeliefert) Vorbereitungen UKW-Antenne** (mitgeliefert) * Richten Sie die Antenne neu aus, wenn Sie den Empfang verbessern wollen. ** Die Antenne sollte so horizontal wie möglich ausgerichtet sein.
Anschließen des Systems (Fortsetzung) Tip Je nach Polarität des Steckers kann die Klangqualität unterschiedlich sein. Ändern Sie die Richtung, in der Sie den Stecker einstecken, und überprüfen Sie die Klangqualität. 3 Anschließen des Netzkabels Schließen Sie das Netzkabel an eine Netzsteckdose an. 4 Einlegen der Batterien in die Fernbedienung Legen Sie zwei R6-Batterien (Größe AA) (nicht mitgeliefert) ein.
Auswählen der Klangbetonung SOUND (Klangmodus/MEGA BASS) Sie können die Klangbetonung der Musik, die Sie wiedergeben lassen, einstellen. Vorbereitungen Auswählen der Klangeigenschaft Wählen Sie mit SOUND die gewünschte Klangbetonung. Option Ergebnis kraftvolle, klare Klänge mit Betonung des unteren und oberen Klangspektrums “MEGA BASS” erscheint im Display.
Weitere Informationen Sicherheitsmaßnahmen Sicherheit • Der Laser-Strahl, den dieser CD-Player generiert, schädigt die Augen. Versuchen Sie daher nicht, das Gerät zu zerlegen. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal. • Sollten Fremdkörper oder Flüssigkeiten in das Gerät gelangen, trennen Sie es von der Netzsteckdose, und lassen Sie es von qualifiziertem Fachpersonal überprüfen, bevor Sie es wieder benutzen.
• Wurde das Gerät lange Zeit nicht benutzt, schalten Sie es in den Wiedergabemodus, und warten Sie ein paar Minuten lang ab (Aufwärmzeit), bevor Sie eine Kassette einlegen. • Kleben Sie weder Papier noch Klebeband auf die CD, und achten Sie darauf, daß die Oberfläche der CD nicht zerkratzt wird. Sollten an Ihrem Gerät Probleme auftreten oder sollten Sie Fragen haben, wenden Sie sich bitte an Ihren SonyHändler. Kratzer, Schmutz oder Fingerabdrücke auf der CD können zu Spurführungsfehlern führen.
Störungsbehebung Abhilfemaßnahme Es ist kein Ton zu hören. • Schalten Sie das Gerät mit der Taste OPERATE ein. • Schließen Sie das Netzkabel korrekt an eine Netzsteckdose an. • Schließen Sie das Netzkabel an die Buchse POWER IN des Geräts an (Seite 23). • Schließen Sie das Audioverbindungskabel korrekt an (Seite 24). • Stellen Sie die Lautstärke ein. • Ziehen Sie das Kopfhörerkabel aus der Buchse, wenn Sie den Ton über die Lautsprecher hören wollen.
Kassettenrecorder Timer Symptom Abhilfemaßnahme Das Band läuft nicht, wenn Sie eine Bandtransporttaste drücken. • Das Kassettenfach muß korrekt geschlossen sein. Die Taste REC r funktioniert nicht/Das Band wird nicht abgespielt. • Die Überspielschutzlasche an der Kassette muß intakt sein. • Drücken FUNCTION, um am Gerät die Funktion “TAPE” einzuschalten. Das Band wird nicht vollständig gelöscht. • Reinigen Sie die Löschköpfe (siehe Seite 33). Das Band wird nicht bespielt.
Störungsbehebung (Fortsetzung) Abhilfemaßnahme Die Fernbedienung funktioniert nicht. • Tauschen Sie alle Batterien in der Fernbedienung gegen neue aus, wenn sie schwach sind. • Achten Sie darauf, die Fernbedienung auf den Fernbedienungssensor am Gerät zu richten. • Entfernen Sie Hindernisse zwischen Fernbedienung und Gerät. • Achten Sie darauf, daß der Fernbedienungssensor keiner starken Lichteinstrahlung, zum Beispiel direktem Sonnenlicht oder dem Licht einer Leuchtstoffröhre, ausgesetzt ist.
Wartung Reinigen der Linse Wenn die Linse verschmutzt ist, kann es bei der CD-Wiedergabe zu Tonsprüngen kommen. Reinigen Sie die Linse mit einem handelsüblichen Staubbläser. Reinigen der Tonköpfe und des Bandtransportwegs Um eine gute Wiedergabe- und Aufnahmequalität sicherzustellen, wischen Sie Tonköpfe, Andruckwalzen und Kapstan nach jeweils 10 Betriebsstunden mit einem Wattestäbchen ab, das Sie leicht mit einer Reinigungsflüssigkeit oder Alkohol angefeuchtet haben.
Technische Daten CD-Player Allgemeines System Digitales CD-Audio-System Eigenschaften der Laserdiode Material: GaAlAs Wellenlänge:780 nm Emissionsdauer: Kontinuierlich Laseremission: weniger als 44,6 µW (gemessen im Abstand von 200 mm von der Linsenoberfläche am optischen Sensorblock mit einer Apertur von 7 mm) Spindelgeschwindigkeit 200 U/min bis 500 U/min (CLV) Anzahl der Kanäle 2 Frequenzgang 20 - 20.
Index A K T Anschließen Klangbetonung 27 Timer Antennen 25 Klangmodus 27 Aufwachen mit Musik 20 M Einschlafen mit Musik 22 des Netzkabels 26 Lautsprecher 23 System 23 Ansteuern eines bestimmten Titels 13 Aufnehmen auf eine Kassette 10 Auswählen Klangbetonung 27 MEGA BASS 27 P V Program Play 15 Verbessern des Radioempfangs 7 R Vorbereitungen 23 Radioempfang 6 Radiosender Titel 5, 13 einstellen 18 AUTO PRESET 17 B einer Kassette 8 Gehäuse 33 gespeicherter Radiosender 18 Tonköpfe und
36D Weitere Informationen
Weitere Informationen 37D