3-860-142-16(1) Personal Component System Operating Instructions page 2EN EN Bedienungsanleitung Seite 2D D PMC-D305L PMC-D307L 1997 by Sony Corporation
Warning CAUTION To prevent fire or shock hazard, do not expose the player to rain or moisture. You can use this player on AC power source only. You cannot use it on batteries. When you use this player for the first time, or when you have not used it for a long time, leave it connected to AC power source for about one hour to charge the built-in backup battery for the clock, timer, preset radio stations, etc. You can use the player during charging.
Table of contents Basic Operations Basic Operations 4 Playing a CD 6 Listening to the radio 8 Playing a tape 10 Recording on a tape The CD Player 12 Using the display 13 Locating a specific track 14 Playing tracks repeatedly (Repeat Play) 15 Creating your own program (Program Play) The Radio 17 Presetting radio stations 18 Playing preset radio stations The Timer 20 21 23 24 EN Setting Up 26 Hooking up the system 30 Connecting optional components 32 Selecting the audio emphasis (Sound Mode/MEGA B
Basic Operations Playing a CD 3 1,2 For hookup instructions, see pages 26 - 29. 1 Press 6 OPEN/CLOSE down to open the CD compartment and place the CD on the CD compartment. With the label side up 2 3 Close the lid of the CD compartment. Press ( on the CD section (direct power-on). The player plays all the tracks once.
Use these buttons for additional operations OPERATE P p VOLUME +/– =/+ Tip Next time you want to listen to a CD, just press (. The player turns on automatically and starts playing the CD. To Press Adjust the volume VOLUME +/– Stop playback p Pause playback P Press again to resume play after pause.
Listening to the radio 1 2 For hookup instructions, see pages 26 - 29. 1 2 Press BAND until the band you want appears in the display (direct power-on). Hold down TUNE +/– until the frequency digits begin to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button once at a time. 6EN Basic Operations Display Indicates an FM stereo broadcast.
Use these buttons for additional operations OPERATE PLAY MODE MONO/ST/ISS Tips • If the FM broadcast is noisy, press PLAY MODE/MONO/ST/ISS on the player until “Mono” appears in the display and the radio will play in monaural. • Next time you want to listen to the radio, just press BAND. The player turns on automatically and starts playing the previous station.
Playing a tape 1 2 For hookup instructions, see pages 26 - 29. 1 Press 6 PUSH to open the tape compartment and insert a recorded tape. Use TYPE I (normal) tape only. Close the compartment. With the side you want to play facing forward 2 Press ( on the TAPE section. Display The player turns on (direct power-on) and starts playing.
Use these buttons for additional operations OPERATE 9 p 0/) Basic Operations VOLUME +/– 6 PUSH DIR MODE Tips • Press COUNTER RESET on the remote to reset the counter to “000.” (on the remote only) • Next time you want to listen to a tape, just press ( or 9 . The player turns on automatically and starts playing the tape.
Recording on a tape 3 3 1 For hookup instructions, see pages 26 - 29. 1 Press 6 PUSH to open the tape compartment and insert a blank tape. Use TYPE I (normal) tape only. With the side you want to record on facing forward 2 Select the program source you want to record. To record from the CD player, insert a CD (see page 4) and press p on the CD section. To record from the radio, press BAND and tune in the station you want (see page 6.
3 Start recording. r/P 1 Press r/P. Recording from the CD player 2 Press ( (for the front side) or 9 (for the reverse side) on the TAPE section to select the recording side of the tape. Recording from the radio Recording will start automatically. Basic Operations The 9/( indication in the display flashes. (On the remote, while keeping r/P pressed, press ( or 9 on the TAPE section.) Note If recording does not start, press r/P and then ( or 9 again.
The CD Player Using the display You can check information about the CD using the display. DISPLAY/ ENTER Checking the total track number and playing time Press DISPLAY/ENTER in stop mode. If the CD has more than 10 tracks, “OVER 10” appears in the display. Total playing time Total track number Music calendar Checking the remaining time Press DISPLAY/ENTER while playing a CD. The track numbers in the music calendar disappear after they are played.
Locating a specific track Number buttons The CD Player You can quickly locate any track using the number buttons. You can also find a specific point in a track while playing a CD. 0/–, )/+ Note You cannot locate a specific track if “PGM” or “SHUF REP” is lit in the display. Turn off the indication by pressing p on the CD section. Tip When you locate a track numbered over 10, press > 10 first, then the corresponding number buttons. Example: To play track number 23, press >10 first, then 2 and 3.
Playing tracks repeatedly (Repeat Play) Number buttons You can play tracks repeatedly in normal, shuffle or program play modes (see pages 15 and 16.) MODE p ( Note When you repeat a single track or all the tracks, make sure neither “PGM” nor “SHUF REP” is lit in the display. If either is lit, turn it off by pressing p on the CD section. 1 Press p on the CD section. “Cd” appears in the display. 2 3 Press MODE until the repeat mode you want appears in the display.
Creating your own program (Program Play) MODE p The CD Player Number buttons You can make a program of up to 20 tracks in the order you want them to be played. ( Tips • To create your own program on the player by selecting the track you want while listening to the CD, proceed as follows: 1 Press ( on the CD section to start play. 2 Press PGM SET/ AUTO PRESET . “PGM” flashes in the display. 3 Press =/+ to select the track you want to program, and press DISPLAY/ ENTER/MEM. Repeat this step. 4 Press p.
Creating your own program (Program Play) (continued) Notes • You can play the same program again, since the program is saved until you open the CD compartment. • You can record your own program. After you’ve created the program, insert a blank tape into the tape compartment and press r/P and ( (or 9) to start recording. 16EN The CD Player To cancel Program Play Press MODE until “PGM” disappears in the display. To check the order of tracks before play Press + on the player.
The Radio Presetting radio stations PGM SET/AUTO PRESET BAND The Radio You can store radio stations into the player's memory. You can preset up to 30 radio stations, 10 for each band in any order. 1 Press BAND until the band you want appears in the display. 2 Press PGM SET/AUTO PRESET until “AUTO ” appears. The stations are stored in memory from the lower frequencies unless a station has a weak signal.
Playing preset radio stations Once you've preset the stations, use the number buttons to tune in your favorite stations. Number buttons BAND Tip You can tune in a preset station with the player. Use PRESET +/– instead of the number buttons. 18EN The Radio 1 2 Press BAND to select the band. Press the number buttons to tune in a stored station.
The Tape Player Finding the beginning of a track The player senses where a track begins by detecting the pauses between the tracks. Notes • If a soft sound like pianissimo continues for some seconds in a track, the player may start to play as the next track. • If you press the ) or 0 when there is no sound in the track, this function does not operate correctly. • To find the beginning of a track correctly, a pause of approx. 4 seconds is necessary.
The Timer Setting the clock “0:00” indication appears in the display until you set the clock. As long as the clock goes, “:” flashes. TIMER/ CLOCK DISPLAY/ ENTER 0/–, )/+ Tip The time display system: 24-hour system Before you begin, hook up the systems (see page 26.) 1 Press and hold TIMER/CLOCK for about 2 seconds until the hour digit flash. 2 Set the clock. 1 Press 0/– or )/+ to set the hour and press DISPLAY/ ENTER. . 2 Press 0/– or )/+ to set the minutes. 3 Press DISPLAY/ENTER.
Waking up to music STANDBY You can wake up to music or a radio program at a preset time. Make sure you have set the clock (“Setting the clock” on page 20). TIMER/ CLOCK Note You cannot preset wake-up timer and recording timer (page 24) at the same time. The Timer DISPLAY/ ENTER 0/–, )/+ Before you begin, make sure the t (clock) indication is not lit in the display. If it is lit, press STANDBY. 1 Prepare the music source you want to play. Source 2 Do this CD Insert a CD. TAPE Insert a tape.
Waking up to music (continued) Tips • The display window does not light while the waking up timer is operating even if the power is on. • You can have the player go on the next day at the same time. Just press STANDBY until the t indication appears in the display. The preset settings remain until you reset them. 5 Set the timer to the hour and the minutes you want the music to go on. 1 Press 0/– or )/+ to set the hour and press DISPLAY/ ENTER.
Falling asleep to music SLEEP You can set the player to turn off automatically after 10, 20, 30, 60, 90 and 120 minutes, allowing you to fall asleep while listening to music. The Timer Tips • The display window does not light while the sleep timer is on. • You can combine the waking up timer with the sleeping timer. Set the waking up timer first (see page 21), turn on the power, and then set the sleep timer. • You can prepare the different music for the waking up timer and the sleeping timer.
Timer-recording radio programs STANDBY You can set timer to record the radio at a certain time. You can also record the sound of the component connected to the LINE IN jack, using the timer. Make sure you have set the clock (see “Setting the clock” on page 20.) TIMER/ CLOCK DISPLAY/ ENTER 0/–, )/+ Note You cannot preset recording timer and wake-up timer (page 21) at the same time. Tip When you receive the MW/LW program in step 1, press r/P to check if the noise is heard.
6 Set the timer to the hour and the minutes you want to start recording. 1 Press 0/– or )/+ to set the hour and press DISPLAY/ ENTER. 2 Press 0/– or )/+ to set the minutes and press DISPLAY/ ENTER. Tips • The preset settings remain until you reset them. • When you select both sides recording, the recording will stop after the both sides recording finishes so that accidental recording will not be made. • The display window does not light while the recording timer is on.
Setting Up Hooking up the system 2 MW/LW loop aeral 2 FM aerial 1 Audio connecting cord Make sure you turn off the power before making any connections. Right speaker Left speaker 1 Speaker cord 1 Power cord To a wall outlet 3 AC power cord Note Connect the right speaker for this unit only to the speaker terminals of the left speaker. If you connect any other speaker or equipment, malfunction may occur. Tip PMC-D307L only: This unit comes supplied with 8 round (10 mm diameter) slip stoppers.
2 Connect the audio connecting cord (supplied) to the SIGNAL OUTPUT jacks of the player and the SIGNAL INPUT jacks of the left speaker. Connect the white plugs to the L (left) jacks and the red plugs to the R (right) jacks. Setting Up 3 Connect the speaker cord of the right speaker to the SPEAKER OUT terminals of the left speaker. Connect the red wire to the (+) plus terminal, and the black wire to the (–) minus terminal.
Hooking up the system (continued) Note Keep the aerials away as far as possible from the speaker cords and other connecting cords. If you do not, noise may be heard. 2 Hooking up the aerials MW/LW loop aerial* (supplied) FM aerial** (supplied) *Reorient the aerial to improve broadcast reception. **Keep the aerial as horizontal as possible. Setting up the MW/LW loop aerial Tip The sound quality may be changed depending on the polarity of the plug.
4 Inserting batteries into the remote Insert two R6 (size AA) batteries (not supplied) To improve the FM reception Setting Up Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Disconnect the supplied FM aerial and connect the FM outdoor aerial (not supplied). If you use a distributor, you can also use the TV aerial.
Connecting optional components FUNCTION You can enjoy the sound from a VCR or MiniDisc player/ recorder through the speakers of this player. Be sure to turn off the power of each component before making connections. For details, refer to the instruction manual of the component to be connected. Note Connect the cables firmly to avoid any malfunction. Tip You can record the sound of the connected component. Insert a cassette, and while keeping r/P pressed, press ( of the tape player.
Notes • As long as “Cd” appears in the display, the optical digital output jack is in operation and the jack lights even if the CD is in stop mode. • If you play a CD-ROM that is not for audio use, noise may be heard. Recording a CD on a MiniDisc recorder and DAT recorder Front panel of this player MiniDisc recorder, DAT recorder, etc.
Selecting the audio emphasis SOUND (Sound Mode/MEGA BASS) You can adjust the audio emphasis of the sound you are listening to. Selecting the sound characteristic Press SOUND to select the audio emphasis you want. Choose To get powerful, clean sounds, emphasizing low and high range audio “MEGA BASS” appears in the display.
Additional Information Precautions On safety • As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components.
Precautions (continued) Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. Notes on cassettes • Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. Side A • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs.
Troubleshooting Remedy There is no audio. • Press OPERATE to turn on the player. • Connect the AC power cord to a wall outlet securely. • Connect the power cord to the POWER IN of the player (page 26). • Connect the audio connecting cord correctly (page 27.) • Adjust the volume. • Unplug the headphones when listening through speakers. “no disc“ lights in the display even when a CD is in place. • Insert the CD with the label surface up. The CD does not play. • • • • The sound drops out.
Timer Tape Player Troubleshooting (continued) 36EN Symptom Remedy The tape does not move when you press an operation button. • Close the cassette compartment securely. The r/P button does not function/The tape does not play. • Make sure the safety tab on the cassette is in place. • Press p on the TAPE section to switch the function of the player to “TAPE”. The tape does not erase completely. • Clean the erasing heads (see page 38.) The tape does not record.
Remote Symptom Remedy The remote does not function. • Replace all the batteries in the remote with new ones if they are weak. • Make sure that you are pointing the remote at the remote sensor on the player. • Remove any obstacles in the path of the remote and the player. • Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. • Move closer to the player when using the remote.
Maintenance Cleaning the lens If the lens becomes dirty, it may cause a skipping of sound during CD operation. Clean with a commercially available blower. Cleaning the tape heads and tape path Wipe the heads, the pinch rollers and the capstans with a cleaning swab slightly moistened with cleaning fluid or alcohol after every 10 hours of operation for optimum playback and recording quality.
Specifications CD player section General System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length:780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20,000 Hz +1/–2.
Index A I, J, K S Audio emphasis 32 Selecting AUTO PRESET 17 Improving broadcast reception 7 B L Batteries for remote 29 CD player 12 Cleaning cabinet 38 tape heads and tape path 38 MEGA BASS 32 Playing a CD 4 a tape 8 tracks repeatedly 14 Waking up to music 21 Presetting radio stations 17 Troubleshooting 35 Program Play 15 U, V, W, X, Y, Z Using the display 12 Radio stations playing 18 presetting 17 Recording aerials 28 speakers 26 system 26 Additional Information Falling asleep to mus
Additional Information 41EN
Achtung VORSICHT Um Feuergefahr und die Gefahr eines elektrischen Schlags zu vermeiden, setzen Sie das Gerät weder Regen noch sonstiger Feuchtigkeit aus. Sie können dieses Gerät nur mit Netzstrom betreiben. Sie können es nicht mit Batterien betreiben.
Inhalt Grundfunktionen Grundfunktionen 4 Wiedergeben einer CD 6 Radiobetrieb 8 Wiedergeben einer Kassette 10 Aufnehmen auf eine Kassette Der CD-Player 12 Das Display 13 Ansteuern eines bestimmten Titels 14 Wiederholtes Wiedergeben von Titeln (Repeat Play) 15 Zusammenstellen eines eigenen Programms (Program Play) Das Radio 17 Speichern von Radiosendern 18 Wiedergeben gespeicherter Radiosender Der Kassettenrecorder 19 Ansteuern des Anfangs eines Titels Der Timer 20 21 23 24 Einstellen der Uhr Aufw
Grundfunktionen Wiedergeben einer CD 3 1,2 Informationen zum Anschließen des Systems finden Sie auf Seite 26 - 29. 1 Öffnen Sie mit 6 OPEN/CLOSE das CD-Fach, und legen Sie die CD in das CD-Fach ein. Mit der beschrifteten Seite nach oben 2 3 Schließen Sie den Deckel des CDFachs. Drücken Sie ( im CD-Feld (Direkteinschaltfunktion). Der CD-Player gibt alle Titel einmal wieder.
Folgende Tasten stehen für weitere Funktionen zur Verfügung: P p 6 OPEN/CLOSE VOLUME +/– =/+ Tip Wenn Sie das nächste Mal eine CD hören wollen, drücken Sie einfach (. Das Gerät schaltet sich automatisch ein und beginnt die Wiedergabe der CD. Zum Grundfunktionen OPERATE Drücken Sie Einstellen der Lautstärke VOLUME +/– Beenden der Wiedergabe p Unterbrechen der Wiedergabe P Drücken Sie die Taste erneut, um die Wiedergabe nach einer Pause fortzusetzen.
Radiobetrieb 1 2 Informationen zum Anschließen des Systems finden Sie auf Seite 26 - 29. 1 2 Drücken Sie BAND, bis der gewünschte Frequenzbereich im Display angezeigt wird (Direkteinschaltfunktion). Display Halten Sie TUNE +/– gedrückt, bis die Ziffern der Frequenzangabe im Display durchzulaufen beginnen. Zeigt an, daß es sich um einen UKWStereosender handelt.
Folgende Tasten stehen für weitere Funktionen zur Verfügung: PLAY MODE MONO/ST/ISS VOLUME +/– Tips • Wenn beim UKWEmpfang Störgeräusche auftreten, drücken Sie PLAY MODE/MONO/ ST/ISS am Gerät, bis “Mono” im Display erscheint. Der Radioempfang ist in diesem Fall monaural. • Wenn Sie das nächste Mal Radio hören wollen, drücken Sie einfach BAND. Das Gerät schaltet sich automatisch ein, und der zuvor eingestellte Sender ist zu hören.
Wiedergeben einer Kassette 2 1 Informationen zum Anschließen des Systems finden Sie auf Seite 26 - 29. 1 Öffnen Sie mit 6 PUSH das Kassettenfach, und legen Sie eine bespielte Kassette ein. Verwenden Sie nur Kassetten des Typs TYPE I (normal). Schließen Sie das Kassettenfach. Mit der wiederzugebenden Seite nach vorne 2 Drücken Sie ( im Bedienfeld für den Kassettenrecorder (TAPE). Das Gerät schaltet sich ein (Direkteinschaltfunktion) und startet die Wiedergabe.
Folgende Tasten stehen für weitere Funktionen zur Verfügung: 9 p VOLUME +/– Grundfunktionen OPERATE 0/) 6 PUSH DIR MODE Tips • Drücken Sie COUNTER RESET auf der Fernbedienung, um den Zähler auf “000” zu setzen. Diese Funktion steht nur über die Fernbedienung zur Verfügung. • Wenn Sie das nächste Mal eine Kassette abspielen wollen, drücken Sie einfach ( oder 9. Das Gerät schaltet sich automatisch ein und startet die Wiedergabe der Kassette.
Aufnehmen auf eine Kassette 3 3 1 Informationen zum Anschließen des Systems finden Sie auf Seite 26 - 29. 1 Öffnen Sie mit 6 PUSH das Kassettenfach, und legen Sie eine leere Kassette ein. Verwenden Sie nur Kassetten des Typs TYPE I (normal). Mit der Seite, auf die aufgenommen werden soll, nach vorne 2 Wählen Sie die aufzunehmende Tonquelle. Um vom CD-Player aufzunehmen, legen Sie eine CD ein (siehe Seite 4) und drücken p am CD-Player.
3 Starten Sie die Aufnahme. r/P Aufnehmen vom CD-Player 1 Drücken Sie r/P. 2 Mit ( (Vorderseite) bzw. 9 (Rückseite) im Bedienfeld für den Kassettenrecorder (TAPE) wählen Sie die Aufnahmeseite der Kassette. Aufnehmen vom Radio Grundfunktionen Die Anzeige 9/( blinkt im Display. Die Aufnahme startet automatisch. Auf der Fernbedienung halten Sie dazu r/P gedrückt und drücken ( bzw. 9 im Bedienfeld für den Kassettenrecorder.
Der CD-Player Das Display Im Display können Sie Informationen zur CD anzeigen lassen. DISPLAY/ ENTER Anzeigen der Gesamtzahl der Titel und der Gesamtspieldauer Drücken Sie im Stopmodus DISPLAY/ENTER. Sind auf der CD mehr als 10 Titel vorhanden, erscheint “OVER 10” im Display. Gesamtspieldauer Gesamtzahl der Titel Musikkalender Anzeigen der Restspieldauer Drücken Sie DISPLAY/ENTER während der Wiedergabe einer CD.
Ansteuern eines bestimmten Titels Zahlentasten Der CD-Player Mit Hilfe der Zahlentasten können Sie mühelos jeden beliebigen Titel direkt ansteuern. Darüber hinaus können Sie während der Wiedergabe einer CD eine bestimmte Passage innerhalb eines Titels suchen. 0/–, )/+ Hinweis Sie können einen bestimmten Titel nicht ansteuern, wenn “PGM” oder “SHUF REP” im Display leuchtet. Schalten Sie die Anzeige aus, indem Sie p im CD-Feld drücken.
Wiederholtes Wiedergeben von Titeln (Repeat Play) Zahlentasten Sie können die Titel auf einer CD mehrmals wiedergeben lassen, und zwar wahlweise in der normalen Reihenfolge (Normal Play), in willkürlicher Reihenfolge (Shuffle Play) oder in einer vorher festgelegten Reihenfolge (Program Play) (siehe auf Seite 15 - 16). Hinweis Wenn Sie einen einzelnen Titel oder alle Titel wiederholt wiedergeben möchten, achten Sie darauf, daß weder “PGM” noch “SHUF REP” im Display leuchtet.
Zusammenstellen eines eigenen Programms (Program Play) Der CD-Player Zahlentasten Sie können bis zu 20 Titel in beliebiger Reihenfolge zu einem individuellen Programm zusammenstellen und wiedergeben lassen. MODE p ( Tips • Wenn Sie ein eigenes Programm zusammenstellen wollen, indem Sie während der CD-Wiedergabe die Titel auswählen, gehen Sie folgendermaßen vor: 1 Starten Sie mit ( im CD-Feld die Wiedergabe. 2 Drücken Sie PGM SET/ AUTO PRESET. “PGM” blinkt im Display.
Zusammenstellen eines eigenen Programms (Program Play) (Fortsetzung) Tips • Sie können dasselbe Programm nochmals abspielen, da das Programm gespeichert bleibt, bis Sie das CDFach öffnen. • Sie können Ihr eigenes Programm aufnehmen. Legen Sie nach dem Zusammenstellen des Programms eine leere Kassette in das Kassettenfach ein, und starten Sie die Aufnahme mit r/P und ( (bzw. 9). 16D Der CD-Player So brechen Sie Program Play ab Drücken Sie MODE, bis “PGM” nicht mehr im Display angezeigt wird.
Das Radio Speichern von Radiosendern PGM SET/AUTO PRESET BAND Das Radio Sie können bis zu 30 Radiosender, 10 pro Frequenzbereich, in beliebiger Reihenfolge voreinstellen und im Speicher des Geräts abspeichern. 1 Drücken Sie BAND, bis der gewünschte Frequenzbereich im Display erscheint. 2 Drücken Sie PGM SET/AUTO PRESET, bis “AUTO” erscheint. Die Sender werden in numerischer Reihenfolge, beginnend mit der niedrigsten Frequenz, gespeichert, sofern sie in ausreichender Signalstärke empfangen werden.
Wiedergeben gespeicherter Radiosender Wenn Sie die Radiosender gespeichert haben, können Sie sie mit Hilfe der Zahlentasten mühelos abrufen. Zahlentasten BAND Tip Sie können einen gespeicherten Sender auch mit den Tasten am Gerät einstellen. Verwenden Sie dazu PRESET +/– anstelle der Zahlentasten. 18D Das Radio 1 2 Wählen Sie mit BAND den Frequenzbereich. Stellen Sie mit den Zahlentasten einen gespeicherten Sender ein.
Der Kassettenrecorder Ansteuern des Anfangs eines Titels Das Gerät kann den Anfang eines Titels anhand der Pause zwischen den Titeln erkennen. Hinweise • Wenn ein Titel eine sehr leise Passage von einigen Sekunden Länge enthält, startet das Gerät möglicherweise die Wiedergabe an dieser Stelle. • Wenn Sie an einer Stelle, an der kein Ton aufgezeichnet ist, ) oder 0 drücken, arbeitet diese Funktion nicht korrekt.
Der Timer Einstellen der Uhr Die Anzeige “0:00” erscheint im Display, bis Sie die Uhr einstellen. Wenn die Uhr läuft, blinkt “:” im Display. TIMER/ CLOCK DISPLAY/ ENTER 0/–, )/+ Tip Die Uhrzeit wird im folgenden Format angezeigt: 24-Stunden-Format Schließen Sie zunächst alle Geräte an (siehe Seite 26). 1 Halten Sie TIMER/CLOCK etwa 2 Sekunden lang gedrückt, bis die Stundenangabe blinkt. 2 Stellen Sie die Uhrzeit ein. 1 Stellen Sie mit 0/– oder )/+ die Stunden ein, und drücken Sie dann DISPLAY/ENTER.
Aufwachen mit Musik STANDBY Sie können sich zu einer bestimmten Zeit mit Musik wecken lassen. Dazu muß die Uhr eingestellt sein (siehe “Einstellen der Uhr” auf Seite 20). TIMER/ CLOCK 0/–, )/+ Hinweis Sie können für den Weck-Timer und den Aufnahme-Timer (Seite 24) nicht dieselbe Zeit voreinstellen. Der Timer DISPLAY/ ENTER Sorgen Sie zunächst dafür, daß die Anzeige t (Uhrzeit) nicht im Display leuchtet. Andernfalls drücken Sie STANDBY. 1 Bereiten Sie die wiederzugebende Musikquelle vor.
Aufwachen mit Musik (Fortsetzung) Tips • Das Display leuchtet nicht, solange der Weck-Timer in Betrieb ist, auch wenn das Gerät eingeschaltet ist. • Sie können das Gerät so einstellen, daß es sich am nächsten Tag zur selben Zeit einschaltet. Drücken Sie einfach STANDBY, bis die Anzeige t im Display erscheint. Die Einstellungen bleiben im Gerät gespeichert, bis Sie sie ändern. 5 Stellen Sie die Stunden und Minuten für die Uhrzeit ein, zu der sich die Musik einschalten soll.
Einschlafen mit Musik SLEEP Sie können das Gerät so einstellen, daß es sich automatisch nach 10, 20, 30, 60, 90 oder 120 Minuten ausschaltet. Auf diese Weise können Sie beim Einschlafen Musik hören. Der Timer Tips • Die Anzeige im Display ist abgeschwächt, während der SleepTimer aktiviert ist. • Sie können den WeckTimer mit dem SleepTimer kombinieren. Stellen Sie dazu zuerst den Weck-Timer ein (siehe Seite 21), schalten Sie dann das Gerät ein, und stellen Sie den Sleep-Timer ein.
Aufnehmen von Radiosendungen mit dem Timer STANDBY Sie können mit dem Timer die Aufnahme einer Radiosendung für eine bestimmte Zeit vorprogrammieren. Über den Timer können Sie auch Aufnahmen von einer Tonquelle anfertigen, die an die Buchse LINE IN angeschlossen ist. Dazu muß die Uhrzeit korrekt eingestellt sein (siehe “Einstellen der Uhr” auf Seite 20). Hinweis Sie können für den Aufnahme-Timer und den Weck-Timer (Seite 21) nicht dieselbe Zeit voreinstellen.
6 Stellen Sie die Stunden und Minuten für die Uhrzeit ein, zu der die Aufnahme starten soll. 1 Stellen Sie mit 0/– oder )/+ die Stunden ein, und drücken Sie dann DISPLAY/ENTER. Hinweis Wenn Sie als Bandaufnahmeseite statt der Rückseite (9) die Vorderseite (() einstellen wollen, blenden Sie mit STANDBY die Anzeige t aus und drücken STANDBY nochmals. Tips • Die voreingestellten Einstellungen bleiben erhalten, bis Sie sie wieder ändern.
Vorbereitungen Anschließen des Systems 2 MW/LW-Ringantenne 2 UKW-Antenne 1 Audioverbindungskabel Achten Sie darauf, daß das Gerät ausgeschaltet ist, bevor Sie irgendwelche Anschlüsse vornehmen. Rechter Lautsprecher Linker Lautsprecher 1 Lautsprecherkabel 1 Netzkabel 3 Netzkabel Hinweise Schließen Sie ausschließlich den rechten Lautsprecher für dieses Gerät an die Lautsprecheranschlüsse des linken Lautsprechers an.
2 Schließen Sie das Audioverbindungskabel (mitgeliefert) an die Buchsen SIGNAL OUTPUT des Geräts und an die Buchsen SIGNAL INPUT des linken Lautsprechers an. Schließen Sie die weißen Stecker an die Buchsen L (links) und die roten Stecker an die Buchsen R (rechts) an. Vorbereitungen 3 Schließen Sie das Lautsprecherkabel des rechten Lautsprechers an die Anschlüsse SPEAKER OUT des linken Lautsprechers an. Schließen Sie das rote Kabel an den Plus-Pol (+) und das schwarze Kabel an den Minus-Pol (–) an.
Anschließen des Systems (Fortsetzung) Hinweis Halten Sie die Antennen so weit wie möglich von den Lautsprecher- und sonstigen Verbindungskabeln fern. Andernfalls können Störgeräusche zu hören sein. 2 Anschließen der Antennen MW/LW-Ringantenne* (mitgeliefert) UKW-Antenne** (mitgeliefert) * Richten Sie die Antenne neu aus, wenn Sie den Empfang verbessern wollen. ** Die Antenne sollte so horizontal wie möglich ausgerichtet sein.
Tip Je nach Polarität des Steckers kann die Klangqualität unterschiedlich sein. Ändern Sie die Richtung, in der Sie den Stecker einstecken, und überprüfen Sie die Klangqualität. 3 Anschließen des Netzkabels Schließen Sie das Netzkabel an eine Netzsteckdose an. 4 Einlegen der Batterien in die Fernbedienung Austauschen der Batterien Bei normalem Gebrauch beträgt die Lebensdauer der Batterien etwa sechs Monate.
Anschließen zusätzlicher Komponenten FUNCTION Über die Lautsprecher dieses Geräts können Sie beispielsweise den Ton von einem Videorecorder oder einem MDPlayer/Recorder wiedergeben lassen. Achten Sie darauf, alle Komponenten vor dem Anschließen auszuschalten. Einzelheiten dazu finden Sie in der Bedienungsanleitung zu den anzuschließenden Geräten. Hinweis Schließen Sie die Kabel fest an. Andernfalls kann es zu Fehlfunktionen kommen.
Aufnehmen einer CD auf einem MD- oder DAT-Recorder Vorderseite dieses Geräts MD-Recorder, DAT-Recorder usw. an digitalen Eingang Digitales Verbindungskabel* POC-5AB (nicht mitgeliefert) Wenn Sie die Anschlüsse vorgenommen haben, schalten Sie das Gerät ein, und starten Sie die Aufnahme. * Wählen Sie das Verbindungskabel je nach Typ der digitalen Eingangsbuchse des anzuschließenden Recorders aus. Einzelheiten dazu finden Sie in der Bedienungsanleitung zu dem anzuschließenden Gerät.
Auswählen der Klangbetonung SOUND (Klangmodus/MEGA BASS) Sie können die Klangbetonung der Musik, die Sie wiedergeben lassen, einstellen. Auswählen der Klangeigenschaft Wählen Sie mit SOUND die gewünschte Klangbetonung. Option Ergebnis kraftvolle, klare Klänge mit Betonung des unteren und oberen Klangspektrums “MEGA BASS” erscheint im Display.
Weitere Informationen Sicherheitsmaßnahmen Sicherheit • Der Laser-Strahl, den dieser CD-Player generiert, schädigt die Augen. Versuchen Sie daher nicht, das Gerät zu zerlegen. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal. • Sollten Fremdkörper oder Flüssigkeiten in das Gerät gelangen, trennen Sie es von der Netzsteckdose, und lassen Sie es von qualifiziertem Fachpersonal überprüfen, bevor Sie es wieder benutzen.
Sicherheitsmaßnahmen (Fortsetzung) • Wurde das Gerät lange Zeit nicht benutzt, schalten Sie es in den Wiedergabemodus, und warten Sie ein paar Minuten lang ab (Aufwärmzeit), bevor Sie eine Kassette einlegen. • Kleben Sie weder Papier noch Klebeband auf die CD, und achten Sie darauf, daß die Oberfläche der CD nicht zerkratzt wird. Sollten an Ihrem Gerät Probleme auftreten oder sollten Sie Fragen haben, wenden Sie sich bitte an Ihren SonyHändler.
Störungsbehebung Abhilfemaßnahme Es ist kein Ton zu hören. • Schalten Sie das Gerät mit der Taste OPERATE ein. • Schließen Sie das Netzkabel korrekt an eine Netzsteckdose an. • Schließen Sie das Netzkabel an die Buchse POWER IN des Geräts an (Seite 26). • Schließen Sie das Audioverbindungskabel korrekt an (Seite 27). • Stellen Sie die Lautstärke ein. • Ziehen Sie das Kopfhörerkabel aus der Buchse, wenn Sie den Ton über die Lautsprecher hören wollen.
Symptom Abhilfemaßnahme Das Band läuft nicht, wenn Sie eine Bandtransporttaste drücken. • Das Kassettenfach muß korrekt geschlossen sein. Die Taste r/P funktioniert nicht/ Das Band wird nicht abgespielt. • Die Überspielschutzlasche an der Kassette muß intakt sein. • Drücken Sie p im TAPE-Feld, um am Gerät die Funktion “TAPE” einzuschalten. Das Band wird nicht vollständig gelöscht. • Reinigen Sie die Löschköpfe (siehe Seite 38). Das Band wird nicht bespielt.
Fernbedienung Symptom Abhilfemaßnahme Die Fernbedienung funktioniert nicht. • Tauschen Sie alle Batterien in der Fernbedienung gegen neue aus, wenn sie schwach sind. • Achten Sie darauf, die Fernbedienung auf den Fernbedienungssensor am Gerät zu richten. • Entfernen Sie Hindernisse zwischen Fernbedienung und Gerät. • Achten Sie darauf, daß der Fernbedienungssensor keiner starken Lichteinstrahlung, zum Beispiel direktem Sonnenlicht oder dem Licht einer Leuchtstoffröhre, ausgesetzt ist.
Wartung Reinigen der Linse Wenn die Linse verschmutzt ist, kann es bei der CD-Wiedergabe zu Tonsprüngen kommen. Reinigen Sie die Linse mit einem handelsüblichen Staubbläser. Reinigen der Tonköpfe und des Bandtransportwegs Um eine gute Wiedergabe- und Aufnahmequalität sicherzustellen, wischen Sie Tonköpfe, Andruckwalzen und Kapstan nach jeweils 10 Betriebsstunden mit einem Wattestäbchen ab, das Sie leicht mit einer Reinigungsflüssigkeit oder Alkohol angefeuchtet haben.
Technische Daten CD-Player System Digitales CD-Audio-System Eigenschaften der Laserdiode Material: GaAlAs Wellenlänge:780 nm Emissionsdauer: Kontinuierlich Laseremission: weniger als 44,6 µW (gemessen im Abstand von 200 mm von der Linsenoberfläche am optischen Sensorblock mit einer Apertur von 7 mm) Spindelgeschwindigkeit 200 U/min bis 500 U/min (CLV) Anzahl der Kanäle 2 Frequenzgang 20 - 20.
Index A K T Anschließen Kassettenrecorder 19 Timer Antennen 28 Klangbetonung 32 des Netzkabels 29 Klangmodus 32 Aufnehmen von Radiosendungen mit dem Timer 24 M Aufwachen mit Musik 21 Lautsprecher 26 System 26 Zusätzliche Komponenten 30 MEGA BASS 32 P Ansteuern eines bestimmten Titels 13 Program Play 15 Aufnehmen R Verbessern des Radioempfangs 7 Radioempfang 6 Vorbereitungen 26 auf eine Kassette 10 Auswählen Klangbetonung 32 einstellen 18 W speichern 17 Wiedergeben AUTO PRESET 17