4-253-728-11(1) Custom Integrated AV System Installation Manual Owner’s Record The model and serial numbers are located on the rear panel. Record the model and serial numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. CAV-M1000ES 2004 Sony Corporation Serial No.
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. – Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. CAUTION You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment.
TABLE OF CONTENTS Chapter 1 Getting Started Features 4 Chapter 5 Appendix LEARN Mode Code List 34 Index 37 Using the RF Remote Control 39 Unpacking 6 Parts and Controls Using the Keypad 40 7 Before Customizing the System Using the IR Remote Control for the Keypad 41 14 Chapter 2 Setting up the Main Unit Installing the Main Unit 15 Hooking up the Main Unit 16 Selecting the Source and the Volume Level of the Main Unit 18 Setting up the Remote Code and the Baud Rate – SETUP mode 19 Learning the Remote
Chapter 1 Getting Started This chapter provides you with information on the features of the system, its accessories, and the parts and controls of each component. 4 Features You can control up to eight audio/video sources in up to six zones with this Custom Integrated AV System.
Main Unit Keypad • LCD contrast adjustment. • Connecting IR IN to an IR emitter enables you to use the IR Remote Control for the additional range. • RJ45 connectors enable you to use two Keypads in a single zone. RF Remote Control • LCD panel configurable through your computer. • Controls the audio/video sources in the main zone and the other zones. • Customize touch panels via an RS232C cable connected to your computer.
Unpacking Getting Started The CAV-M1000ES system includes the following components: • CAV-M1000ES Main Unit • RM-TP100 RF Remote Control • Charger cradle for the RF Remote Control • AN-M1000 RF Antenna • AC power cord • Plug-in 4-terminal screw-type connector for speaker (6) • RF Antenna cable • Installation Manual (this manual) Optional Accessories: RMR-K100 Keypad • IR Remote Control • Keypad mounting bracket • Screws for fixing the Keypad to the Keypad mounting bracket (2) • Installation Guide 6
Parts and Controls Front panel of the Main Unit 2 3 CHECK PROGRAM LEARN 4 6 ZONE SOURCE SELECT SETUP ZONE VOLUME ENTER 5 Getting Started 1 MODE BACK CANCEL ALL ZONE MUTING RS232C 7 8 9 q; qa qs qd qf 1 ?/1 (POWER) switch Press to turn the power on or off. 8 PROGRAM Press to initiate a firmware update. 2 Learning IR window Used to input remote codes into the Main Unit. 9 Cursor/ENTER Press to select a menu. 3 Display window Displays various information.
Parts and Controls Getting Started Rear panel of the Main Unit qg qh IR OUT ANTENNA IR OUT IR OUT IR OUT qj qk ql IR OUT IR OUT IR OUT IR OUT IR OUT COMMON VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT 12V TRIGGER 1 2 3 4 5 6 AUDIO IN AUDIO OUT AUDIO IN AUDIO OUT AUDIO IN AUDIO OUT AUDIO IN AUDIO OUT AUDIO IN AUDIO OUT AUDIO IN AUDIO OUT AUDIO IN AUDIO OUT AUDIO IN AUDIO OUT L
w; ZONE connection jacks b) VIDEO OUT (page 17) An RCA jack that sends a source video signal selected by the zone to the composite video input on a zone display. c) FIXED PRE OUT (zones 1 to 4) An RCA jack for connecting zone audio output to an external amplifier. For use with applications where either more power is required for a zone, or for passing signals to a Dolby Prologic-compatible receiver for theater quality audio in one or more zones.
Parts and Controls Getting Started Front panel of the Keypad 1 qa 2 2 qs 3 PAGE SOURCE MUTING 4 qd 5 qf 6 7 VOLUME POWER qg 8 9 q; 1 IR sensor Receives IR signals from the IR Remote Control for the Keypad (supplied) to control both source components and the system. 2 SELECT Press to select a menu on the LCD display, such as a source menu, a disc title list, etc. 3 PAGE Press to return to the previous menu or to view the current status of the disc title list and the preset station list.
Rear panel of the Keypad Getting Started TO SPEAKERS FROM AMPLIFIER R R L L qh OUT w; IN qj wa MODE qk IR IN SUB MAIN ql qh TO SPEAKERS (page 27) Connects speaker cords to the speakers in a zone. qj CAT5 OUT (page 27) Connects a CAT5 cable to the CAT5 IN jack of the subsidiary Keypad when used in a single room qk IR IN (page 27) Connects an optional IR cord so you can operate the IR Remote Control for the Keypad by pointing it at the IR sensor of the IR emitter.
Parts and Controls Getting Started IR Remote Control for Keypads Buttons marked in grey are used to control the source components. 1 SLEEP Press to activate the sleep function that turns off the Keypad automatically after the specified duration. The time changes as shown below 2:00 t1:30 t1:00 t0:30 tOFF 2 DIMMER Press repeatedly to change the brighteness of the LCD backlight. 3 Numeral Press to select a number, representing, for example, a desired track of the source.
qj SLEEP DIMMER TV 1 2 3 4 5 6 7 8 9 0 >10 2 3 Getting Started 1 qk ql ENTER SELECT 4 5 6 LOCK DISC PAGE SOURCE DOWN UP w; wa 7 8 9 q; ws wd wf TOP MENU/ GUIDE MENU MUTING qa VOLUME qs wg wh wj qd qf DISPLAY TV VOL RETURN/EXIT TV CH FOLDER F1 TV/VIDEO F2 wk qg wl qh e; ea 13
Before Customizing the System Getting Started Be sure to read the following procedure thoroughly before you actually make any settings. Overview The following chart gives an overview of how to set up the Main Unit system. Setting up the Main Unit - Install the Main Unit. (page 15) - Connect components, such as source components and outut components, to the Main Unit. (page 16) - Make other connections. Setting up a Keypad - Install the Keypad into a junction box.
Chapter 2 Setting up the Main Unit When you mount the Main Unit, note the following: •Place the Main Unit in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver. • Do not place the Main Unit near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions. • Do not cover the rear panel.
Hooking up the Main Unit CONTROL A1II jack (D) Hook up each CONTROL A1II jack of the source equipment such as XXXX and the Main Unit. Use a CONTROL A1II cable. You can control the connected source component from the Main Unit. Before hooking up the Main Unit, be sure the power cord is unplugged. Refer to the figures below for the connections. Source component hookups Setting up the Main Unit IR OUT jack (E) Plug the IR emitter into the IR OUT jack of each SOURCE connection jack of the Main Unit.
Output component hookups VIDEO OUT jack (G) Hook up the VIDEO OUT jack of each SOURCE connection jack of the Main Unit and each video input of the external A/V receiver. Use RCA video cables. Hook up the RF ANTENNA jack of the Main Unit and the jack of the RF Antenna. Use a CAT5 cable. AC power cord hookup (N) Connect the supplied AC power cord to the AC IN jack. IR OUT COMMON jack (H) Plug the IR emitter into the IR OUT COMMON jack of the Main Unit.
Selecting the Source and the Volume Level of the Main Unit In the NORMAL mode, you can select a source component for each zone. The status information for each zone appears on the display window. Setting up the Main Unit 1 2 Select a zone by pressing the ZONE + or ZONE – button. Select a source component by pressing the SOURCE + or SOURCE – button. The source component is confirmed one second after you release the SOURCE button.
Setting up the Remote Code and the Baud Rate – SETUP mode Setting the baud rate – BAUD RATE SET You can adjust the baud rate between the Main Unit and an FM/AM Receiver (STR) or DVD Mega Changer connected via an RS232C connection. Press MODE repeatedly until ”<>” appears in the display window, then press ENTER. 2 Press the R cursor or r cursor to select ”BAUD RATE SET”. 3 Press ENTER. ”WHICH PORT?” appears for a few seconds. 4 Press the R cursor or r cursor to select a port.
Learning the Remote Code for a Connected Component – LEARN Mode You can enter any remote codes, even if the remote code that you want to enter is not preset in the SETUP mode. 5 Learning the remote code - CODE LEARNING Press MODE repeatedly until “<>” appears in the display window, then press ENTER. “WHICH MENU?” appears for a few seconds. 2 Press the cursor R or rrepeatedly to select “CODE LEARNING”, then press ENTER. “CONNECT TO?” appears for a few seconds.
You can add new remote codes using EXPAND CODE. • You can add up to 10 additional remote codes to the Main Unit. • You must complete step 5 within one minute after the remote code name is displayed in the display window; otherwise, your entry will not be learned and “LEARN FAILED!” appears. Adding a new remote key - EXPAND CODE 1 2 Press the R cursor or r cursor to select “EXPAND CODE”, then press ENTER. “CONNECT TO?” appears for a few seconds.
Testing Learned Remote Code – CHECK Mode You can check to see if the remote code of the source component have been successfully learned by the Main Unit. Setting up the Main Unit 1 Press SOURCE – or SOURCE + to select the source component that you want to check. 2 Press MODE repeatedly until “<>“ appears in the display window, then press ENTER. “SET COMMAND” appears for a few seconds, then the learned remote code appears.
Adjusting the source input offset – SOURCE INPUT OFFSET You can specify the maximum volume level to optimize the acoustic conditions in each zone. Turn off the power. 3 Press the R cursor or r cursor repeatedly to select a source number. Each time you press the R cursor or r cursor, the display window changes cyclically as shown below. Press and hold ZONE + and ALL ZONE MUTING simultaneously, and then turn on the power. “SOURCE OFFSET” appears in the display window for a few seconds.
Customizing the Main Unit – INSTALLATION Mode Viewing the version information – CIS VERSION CIS VERSION provides you the version information of the Main Unit and other external components, such as an FM/AM Receiver (STR), a DVD Mega Changer, an RF Remote Control, or the Keypad. Setting up the Main Unit 1 1 Turn off the power. 2 Press the cursor R or r to view the version information. Each time you press the button, the display window changes as shown below.
Chapter 3 Installing the Keypad Setting up the Keypad A Keypad must be installed in a junction box (optional). Follow the procedures below to mount a Keypad mounting bracket and a Keypad on the wall. Installing the Keypad This chapter provides you with information regarding installation, hookup and settings for the optional Keypad. 1 Place the Keypad mounting bracket over a junction box which has already been installed on the wall with the mounting lips facing out.
Installing the Keypad 3 Setting up the Keypad 4 Insert the top of the Keypad onto the mounting bracket first, in the direction of the arrow 1 until it clicks, then push the bottom of the Keypad onto the bracket in the direction of the arrow 2. Removing the Keypad 1 Remove the screws that hold the Keypad and the Keypad mounting bracket. 2 Press and hold the edge of the upper-side of the Keypad tightly.
Hooking up in Each Zone You must install at least one Keypad and a pair of speakers in each zone. In the zones where both audio and video will be installed, you must install at least one TV monitor. Requirements for these hookups are as follows. • A CAT5 cable has been installed for each zone's Keypad. • Two pairs of 12 to 18 AWG speaker cords for each pair of speakers. • An RCA video cable for a TV monitor from each zone to the Main Unit location.
Customizing the Keypad Setting bass and treble You can adjust bass and treble to optimize the acoustic conditions in each zone. 1 2 Adjusting LCD contrast 1 2 Turn off the power. 3 Press the corresponding SELECTION buttons to adjust the LCD Contrast Value. 4 Turn off the power when you have finished. The settings are confirmed when the power is turned off. Turn off the power. Press and hold MUTING and LOCK simultaneously, and then press POWER.
Testing the Components It is recommended that you test all the components before you finish with the installation of the entire system in each zone so as not to encounter any problems after the installation is completed. Check to see if the Main Unit, the installed components, and the Keypad operate properly by testing each operation. 1 Select SOURCE 1 by pressing the SELECT SOURCE button on the front panel of the Main Unit. 5 6 Turn on the Keypad in zone 1.
Chapter 4 Other Information This chapter provides you with additional information that will help you understand and maintain your system. Precautions On safety • Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further. • The AC power cord must be changed only at a qualified service shop.
Troubleshooting If you experience any of the following difficulties while using the player, use this troubleshooting guide to help you to remedy the problem. Should any problem persist, consult your nearest Sony dealer. There is no sound, no matter which component is selected. , Check that both the Main Unit and all components are turned on. , Check that all speaker cords are connected correctly. , Press MUTING to cancel the muting function. There is no sound from a specific component.
Error Messages Main Unit If any of the messages below appear on the Display window of the Main Unit, check the following. Other Information Message Cause Corrective action PROTECTOR ZONE1 Protective device in zone 1 has been activated. Ask your nearest Sony dealer. PROTECTOR ZONE2 Protective device in zone 2 has been activated. Ask your nearest Sony dealer. PROTECTOR ZONE3 Protective device in zone 3 has been activated. Ask your nearest Sony dealer.
Specifications CAV-M1000ES Main Unit RM-TP100 RF Remote Control Audio (each channel) Audio (each channel) Continuous average power output (FTC) Operating system: Liquid crystal touch panel All channels: Liquid crystal size: 3.8 inches Frequency response: Input sensitivity: 30 W per channel min. RMS at 8 ohms, any two channels driven from 20 Hz to 20 kHz with no more than 0.09 % HD.
Chapter 5 Appendix This chapter provides you with remote code lists and concise information about operating the system.
Appendix 35
LEARN Mode Code List Appendix 36
Index A AC IN 9,17 AC power cord F1 button 12 F2 button 12 FIXED PRE OUT jack 9, 17, 38 Adding a new remote key 21 FOLDER button 12 Adjusting Volume 38, 39, 40 Source input offset 23 FROM AMPLIFIER jack ALL CLEAR Hookup AC power cord 17 Keypad 17,27 IR emitter 17 Output components RF Antenna 17 Source components Speaker 27 TV monitor 27 Zone related cables AMS button 10, 12 AUDIO IN jack 8, 16 AUDIO OUT jack8, 17 B BACK button Bass 7 28 11 H, I 24 ALL ZONE MUTING button 9 7, 18
Index P T, U, V, W, X, Y, Z PAGE button 10, 12 PAUSE button 10, 12 PC SETUP 19 Planning the system Testing Components 29 Learned remote code 14 TOP MENU/GUIDE button PLAY button 10, 12 TO SPEAKERS jack POWER switch 7, 10 Treble 28 Precautions 30 Troubleshooting 31 PROGRAM button 7 TV CH button TV VOL button Removing the Keypad 26 RS232C connector 7, 9, 16 RF Antenna 15 ,17 RF ANTENNA jack 8 RF Remote Control 9, 38 12 VARIABLE PREOUT jack 9 S VIDEO IN jack SCROLL button
Using the RF Remote Control Commands on the touch panel vary depending on the RF Remote Control programming. Turning the system on or off 1 2 Press SYSTEM OFF. “ALL OFF”, “MAIN OFF”, and “RETURN” appear on the touch panel. Press “ALL OFF” when you want to turn off all zones, and press “MAIN OFF” when you want to turn off the main zone only. Press “RETURN” when you want to cancel the operation. MUTING Turning the RF Remote Control off Leave the RF Remote Control alone for a few minutes.
Using the Keypad Turning the Keypad on or off Adjusting the volume Press POWER to turn the Keypad on. The source components also turn on. To turn the Keypad off, press POWER again. When the last zone is turned off, all the source components also turn off. Press VOLUME +/– to the desired listening level. Muting the volume Press MUTING. To cancel the muting, press MUTING again or VOLUME +. Selecting and controlling the source 1 Press SELECT next to the desired source displayed in the LCD window.
Using the IR Remote Control for the Keypad Buttons marked in grey are used to control the source components. 2 Inserting batteries into the Remote Control Insert two R06 (size-AA) batteries into the battery compartment with the + and – correctly oriented to the markings. When using the Remote, point it at the IR sensor on the Keypad. Press any of the following buttons to control the activated source component. H: Operates the selected source component. X: Pauses playback. x: Stops playback. .
Appendix 42
Appendix 43
Información complementaria 44 Sony Corporation Printed in Malaysia