User's Manual

25GB
E:\DATA\4577101111\4577101111RSXGS9UC\01GB-RSXGS9UC\040CD.fm masterpage: Right
RSX-GS9
4-577-101-11(1)
NFC function
One touch connection (NFC) is not possible.
q The BLUETOOTH signal of this unit is not turned
on.
ˋ Turn the BLUETOOTH signal on (page 9).
q If the smartphone does not respond to the
touching.
ˋ Check that the NFC function of the smartphone
is turned on.
ˋ Move the N-Mark part of the smartphone
closer to the N-Mark part on this unit.
ˋ If the smartphone is in a case, remove it.
q NFC receiving sensitivity depends on the device.
If One touch connection with the smartphone
fails several times, make BLUETOOTH connection
manually.
BLUETOOTH function
The connecting device cannot detect this unit.
q Before the pairing is made, set this unit to pairing
standby mode.
q While connected to a BLUETOOTH device, this
unit cannot be detected from another device.
ˋ Disconnect the current connection and search
for this unit from another device.
q When the device pairing is made, set the
BLUETOOTH signal output to on (page 10).
Connection is not possible.
q The connection is controlled from one side (this
unit or BLUETOOTH device), but not both.
ˋ Connect to this unit from a BLUETOOTH device
or vice versa.
The name of the detected device does not
appear.
q Depending on the status of the other device, it
may not be possible to obtain the name.
No ringtone.
q Adjust the volume by rotating the volume dial
while receiving a call.
q Depending on the connecting device, the
ringtone may not be sent properly.
ˋ Set [Ring Tone] to [TONE 1] (page 18).
q The front speakers are not connected to the unit.
ˋ Connect the front speakers to the unit. The
ringtone is output only from the front speakers.
The talker’s voice cannot be heard.
q The front speakers are not connected to the unit.
ˋ Connect the front speakers to the unit. The
talker’s voice is output only from the front
speakers.
A call partner says that the volume is too low or
high.
q Adjust the volume accordingly using mic gain
adjustment (page 14).
Echo or noise occurs in phone call conversations.
q Lower the volume.
q Set EC/NC Mode to [ECNC 1] or [ECNC 2] (page 14).
q If the ambient noise other than the phone call
sound is loud, try reducing this noise.
E.g.: If a window is open and road noise, etc., is
loud, shut the window. If an air conditioner is
loud, lower the air conditioner.
The phone sound quality is poor.
q Phone sound quality depends on reception
conditions of cellular phone.
ˋ Move your car to a place where you can
enhance the cellular phone’s signal if the
reception is poor.
The volume of the connected audio device is low
(high).
q Volume level will differ depending on the audio
device.
ˋ Adjust the volume of the connected audio
device or this unit.
The sound skips during playback of a
BLUETOOTH audio device.
q Reduce the distance between the unit and the
BLUETOOTH audio device.
q If the BLUETOOTH audio device is stored in a case
which interrupts the signal, remove the audio
device from the case during use.
q Several BLUETOOTH devices or other devices
which emit radio waves are in use nearby.
ˋ Turn off the other devices.
ˋ Increase the distance from the other devices.
q The playback sound stops momentarily when the
connection between this unit and the cellular
phone is being made. This is not a malfunction.
The connected BLUETOOTH audio device cannot
be controlled.
q Check that the connected BLUETOOTH audio
device supports AVRCP.
Some functions do not work.
q Check if the connecting device supports the
functions in question.
A call is answered unintentionally.
q The connecting phone is set to answer a call
automatically.
Pairing failed due to a timeout.
q Depending on the connecting device, the time
limit for pairing may be short.
ˋ Try completing the pairing within the time.
BLUETOOTH function cannot operate.
q Turn off the unit by pressing OFF for more than 2
seconds, then turn the unit on again.
010COV.book Page 25 Thursday, July 2, 2015 2:07 PM