User Guide
Table Of Contents
- Table of Contents
- Overview
- Preparation
- Operating the Camera
- Administrator and User
- Logging in to the System
- Configuration of Main Viewer
- Main menu
- Control panel section
- Monitor image
- Plug-in free viewer
- Using SolidPTZ function
- Controlling via the control panel (Operation common to Area zoom mode and Vector dragging mode)
- Panning and tilting by clicking the monitor image (Area zoom mode only)
- Panning, tilting and zooming by specifying the area (Area zoom mode only)
- Panning and tilting by dragging the screen (Vector dragging mode only)
- Moving the camera to a preset position (Common operations in Area zoom and Vector dragging modes)
- Using pan/tilt/zoom operations with the displayed control bar (PTZ Control bar only)
- Controlling the Camera on a Full Image
- Using the Trigger Button
- Switching TCP/UDP Transmission Mode
- Using the System Utility
- Administrating the Camera
- Basic Operations of the Administrator Menu
- Configuring the System - System Menu
- Setting the Camera Image - Camera Menu
- Configuring the Network - Network Menu
- Setting the SSL function - SSL Menu
- Using the 802.1X Authentication Function - 802.1X Menu
- Setting the User - User Menu
- Setting the Security - Security Menu
- Saving the Camera Position and Action - Preset position Menu
- Sending an Image via E-mail - e-Mail (SMTP) Menu
- Sending Images to FTP Server - FTP Client Menu
- Setting the Operations from the Viewer - Trigger Menu
- Setting the Schedule - Schedule Menu
- Setting the Sensor input/Camera tampering detection/Motion detection - Event detection Menu
- Configuring the Viewer - Viewer Menu
- Others
- Using the SNC toolbox
- Starting SNC toolbox
- How to use SNC toolbox
- Registering in My device
- Changing the Device list display method
- Setting SNC toolbox options
- Using the Custom Homepage - Setting the customized homepage
- Using the Firmware Upgrade
- Using the Schedule Task
- Configuring the device setting
- Camera restart and initialization
- Assigning the IP Address to the Camera Using ARP Commands
- Using the SNMP
- Glossary
- Index
- Using the SNC toolbox
Operating the Camera
Configuration of Main Viewer
22
Frame rate
(Displayed only when the camera image is in JPEG.)
Selects the frame rate to transmit images.
(Capture)
Click to capture a still image shot by the camera and to
store it in the computer. Click to open the folder to be
saved.
Note
In the case of Windows VISTA or Windows 7, if
“Enable Protected Mode” is checked in Control
Panel-Internet Option-Security, still images cannot be
shot.
(Run)/ (Stop Save Video)
Runs and stops Save Video. Click to open the folder
to be saved.
Note
In the case of Windows VISTA or Windows 7, if
“Enable Protected Mode” is checked in Control
Panel-Internet Option-Security, video content cannot be
saved.
Camera control panel
The camera control panel appears when SolidPTZ is set
to On. This panel allows you to control the camera’s
pan/tilt/home position and zoom (page 25). In addition,
you can obtain authority to operate the camera in
exclusive control mode.
Image action
Select the mode of operation from Off, Area zoom and
Vector dragging.
Pan/Tilt control
Click the arrow button the direction in which you want
to move the camera. Keep it pressed to move the camera
continuously.
To return to the home position, click .
Zoom control
Press to zoom out, and press to zoom in.
Zooming continues while the button remains pressed.
Exclusive control
Click this button to display the time remaining for
operation authority. However, if operation authority has
not been obtained, the waiting time is displayed.
Note
Set the Exclusive control mode in the System Tab of the
System Menu to On to perform exclusive control
(page 34).
Panorama panel
It is displayed when SolidPTZ is set to on.
The image will be displayed if capture full image
(page 37) is clicked.
If you click on the Panorama panel, the image of that
place is displayed on the monitor.
Trigger panel
The above is displayed only when Viewer mode
(page 60) is set to Full, and one or more triggers are
enabled in the Trigger menu (page 71).
The configured functions are displayed as buttons on
this panel.
Note
When the Exclusive control mode is set to on, the
configured function cannot be used without operation
authority.