User Guide
Table Of Contents
- Table of Contents
- Overview
- Preparation
- Operating the Camera
- Administrator and User
- Logging in to the System
- Configuration of Main Viewer
- Main menu
- Control panel section
- Monitor image
- Plug-in free viewer
- Using SolidPTZ function
- Controlling via the control panel (Operation common to Area zoom mode and Vector dragging mode)
- Panning and tilting by clicking the monitor image (Area zoom mode only)
- Panning, tilting and zooming by specifying the area (Area zoom mode only)
- Panning and tilting by dragging the screen (Vector dragging mode only)
- Moving the camera to a preset position (Common operations in Area zoom and Vector dragging modes)
- Using pan/tilt/zoom operations with the displayed control bar (PTZ Control bar only)
- Controlling the Camera on a Full Image
- Using the Trigger Button
- Switching TCP/UDP Transmission Mode
- Using the System Utility
- Administrating the Camera
- Basic Operations of the Administrator Menu
- Configuring the System - System Menu
- Setting the Camera Image - Camera Menu
- Configuring the Network - Network Menu
- Setting the SSL function - SSL Menu
- Using the 802.1X Authentication Function - 802.1X Menu
- Setting the User - User Menu
- Setting the Security - Security Menu
- Saving the Camera Position and Action - Preset position Menu
- Sending an Image via E-mail - e-Mail (SMTP) Menu
- Sending Images to FTP Server - FTP Client Menu
- Setting the Operations from the Viewer - Trigger Menu
- Setting the Schedule - Schedule Menu
- Setting the Sensor input/Camera tampering detection/Motion detection - Event detection Menu
- Configuring the Viewer - Viewer Menu
- Others
- Using the SNC toolbox
- Starting SNC toolbox
- How to use SNC toolbox
- Registering in My device
- Changing the Device list display method
- Setting SNC toolbox options
- Using the Custom Homepage - Setting the customized homepage
- Using the Firmware Upgrade
- Using the Schedule Task
- Configuring the device setting
- Camera restart and initialization
- Assigning the IP Address to the Camera Using ARP Commands
- Using the SNMP
- Glossary
- Index
- Using the SNC toolbox
Administrating the Camera
Sending Images to FTP Server — FTP Client Menu
68
Sending Images to FTP
Server
— FTP Client Menu
When you click in the Administrator menu,
the FTP client menu appears.
Use this menu to set up for capturing and sending still
images to an FTP server. Using the FTP client function,
you can send an image file that has been shot and
recorded linked with external sensor input or the built-in
detection functions to an FTP server. An image file can
also be sent periodically.
The FTP client menu consists of three tabs: Common,
Alarm sending and Periodical sending.
Common Tab — Setting the FTP
client function
FTP client function
To activate the FTP client function, select On.
Note
The frame rate and operability on the main viewer may
be reduced while a file is being transmitted by the FTP
client function.
FTP server name
Type either the FTP server name to upload still images
using up to 64 characters, or the IP address of the FTP
server.
User name
Type the user name for the FTP server using up to 64
characters.
Password
Type the password for the FTP server using up to 64
characters.
Re-type password
To confirm the password, type the same characters as
you typed in the Password box.
Passive mode
Set whether you use the passive mode of FTP server or
not when connecting to the FTP server. Select On to
connect to the FTP server using the passive mode.
OK/Cancel
See “Buttons common to every menu” on page 32.
Alarm sending Tab — Setting the
FTP client action when detecting
the alarm
Set to forward an image file to a specified FTP server
linked with alarm detection by the external sensor input
or by the built-in detection functions.
Note
When more than two of the following settings are
activated, the camera only creates two still images at the
same time. A third still image cannot be created unless
one of the previous two still images is sent.
e-Mail (SMTP) menu
– Alarm sending tab Alarm sending (when file
attachment is set to On).
– Periodical sending Periodical sending
FTP client menu
– Alarm sending tab Alarm sending
– Periodical sending Periodical sending
Trigger menu
– Mail (SMTP)
– FTP Client
Alarm sending
Select On to send the image file to the FTP server linked
with alarm detection.
FTP client