AUDIO MONITOR SPEAKER SYSTEM AMS-100 ANALOG MODULE BKAM-101 AES/EBU MODULE BKAM-102 SDI MODULE BKAM-103 INSTALLATION MANUAL 1st Edition
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.
Table of Contents 1. Installation 1-1. Power Supply ........................................................................................1-1 (E) 1-1-1. Power Specifications ............................................................1-1 (E) 1-1-2. Power Cord...........................................................................1-1 (E) Dimensions ............................................................................................1-2 (E) Installation of Boards .................................
1-2. Dimensions 1-3. Installation of Boards 5 350 1-2. Dimensions 424 465 482 Unit : mm 1-3. Installation of Boards The optional boards (BKAM-101/102/103) can be installed in any slots of the AMS-100. Installation of optional boards 1. Turn off the power of the AMS-100. 2. Remove the blank panel on the rear panel after removing its two retainer screws. n Do not discard the removed blank panel. 3. Slide the optional board along the guide rails into the unit. 4.
1-4. Rack Mounting 1-4. Rack Mounting Procedures The AMS-100 can be mounted in a 19-inch standard rack. 1. Turn off the power. 2. Attach the inner rails to the unit using the six screws (B4x8) supplied with the RMM-30. n . If the AMS-100 or the peripheral equipment is mounted in a 19-inch standard rack, it is recommended to install a ventilation fan to prevent a temperature rise in the rack. Make sure that all the units in the rack should be operated within the temperature range of 5dC to 40dC. .
1-4. Rack Mounting 1-5. Pin Assignment of Connectors 4. To mount the unit on the rack, while pressing the stoppers of the inner rails, slide the inner rails fully into the outer rails. 5. After confirming that the unit can be moved smoothly, tighten the six screws run in but not tightened in procedure 3. n To tighten the front brackets to the rack, slide the unit from the rack toward you about 20 mm. 6.
1-6. Matching Connectors and Cables 1-7. Internal Switches 1-6. Matching Connectors and Cables 1-7-2. SDI-43 Board (BKAM-103) When connecting cables to various connectors on the rear panel at the time of installing or servicing, connect the following connectors/cables or their equivalents. Connector Matching Connector/cable Panel indication Connector/Cable Sony Part No.
1-8. Adjustment of the Input Level Meter 1-9. Related manuals 1-8. Input Level Meter Adjustment 1-9. Related manuals Preparation Besides this Installation Manual, the following manuals are available for the AMS-100. . Input the reference signal to the unit: When the BKAM-101 is attached : +4 dBm When the BKAM-102 is attached : _20 dB FS . Turn on the power of the unit and select the slot and the channel to which the reference signal is to be input on the INPUT SELECT operation panel.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer : The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual.
AMS-100 (SY) BKAM-101 (SY) BKAM-102 (SY) BKAM-103 (SY) J, E 3-202-309-01 Sony Corporation Broadcasting & Professional Systems Company Printed in Japan 1999.