REMOTE CONTROL UNIT RM-B750 電気製品は、安全のための注意事項を守らないと、火災 や人身事故になることがあります。 このオペレーションマニュアルには、 事故を防ぐための重要な注意事項と製 品の取り扱いかたを示してあります。 このオペレーションマニュアルをよく お読みのうえ、製品を安全にお使いください。お読みになったあとは、いつ でも見られるところに必ず保管してください。 OPERATION MANUAL 1st Edition [Japanese/English]
安全のために ソニー製品は安全に十分に配慮して設計されています。しかし、電気製品は まちがった使い方をすると、 火災や感電などにより死亡や大けがなど人身事 故につながることがあり、危険です。 事故を防ぐために次のことを必ずお守りください。 安全のための注意事項を守る 警告表示の意味 このオペレーションマニュアル および製品では、次のような表 示をしています。表示の内容を よく理解してから本文をお読み ください。 2(J)∼3(J)ページの注意事項をよくお読みください。 定期点検を実施する 長期間安全に使用していただくために、 定期点検を実施することをおすすめ します。点検の内容や費用については、ソニーのサービス担当者または営業 担当者にご相談ください。 この表示の注意事項を守らない と、火災や感電などにより死亡 や大けがなど人身事故につなが ることがあります。 故障したら使用を中止する ソニーのサービス担当者または営業担当者にご連絡ください。 万一、異常が起きたら 異常な音、に おい、煙が出 たら 炎が出たら , 1 電源を切る。 2 ソニーのサービス担当者または営業担当者に修 理を依頼する
目次 警告 .................................................................................................................... 2(J) 注意 .................................................................................................................... 3(J) 概要 ......................................................................................................................... 4(J) 特長 ..............................................................................................................................
下記の注意を守らないと、 火災や感電により死亡や大けがにつながることがあります。 外装を外さない、改造しない 外装を外したり、改造したりすると、感電の原因となります。 内部の調整や設定および点検を行う必要がある場合は、 必ずサービストレー ニングを受けた技術者にご依頼ください。 内部に水や異物を入れない 水や異物が入ると火災や感電の原因となります。 万一、水や異物が入ったときは、接続コードを抜いて、ソニーのサービス担 当者または営業担当者にご相談ください。 油煙、湯気、湿気、ほこりの多い場所では設置• 使用しない 上記のような場所で設置・使用すると、火災や感電の原因となります。 2 (J)
下記の注意を守らないと、 けがをしたり周辺の物品に損害を与えることがあります。 CAMERA 端子や MONITOR 端子には指定以外の機器を接 続しない このオペレーションマニュアルに記載している以外の機器を接続すると、 火災や感電の原因となることがあります。 リモートコントロールケーブルを傷つけない リモートコントロールケーブルを傷つけると、 火災の原因となることがあ ります。 3 (J)
概要 RM-B750は、ソニーのBVP/HDCシリーズ放送局用CCDカラービ S-EVS機能対応 デオカメラの調整機能を、手元でリモートコントロールするためのリ モートコントロールユニットです。 スーパーEVS (Enhanced Vertical Definition System) 機能対応 付属の専用ケーブルでカメラに直接接続することにより、カメラか のカメラの垂直解像度を、本機から調整できます。 ら最大 50 m 離して使用することができます。 メモリースティックスロット搭載 特長 シーンファイル、リファレンスファイルなど各種データをメモリース ティックに保存し、必要なときに読み出して再現させることができ RM-B750 の主な特長は次のとおりです。 ます。 カメラの基本的オペレーションに対応 他のコントロールパネルとのパラレルコントロー ルが可能 カメラの基本的オペレーションに必要な機能を、手元でコントロール することができます。 カメラコントロールユニットを介してカメラに接続した場合は、マス ターセットアップユニットMSU-700A/750やRCP-700シリーズなど
各部の名称と働き 操作パネル 3 PANEL ACTIVEボタン 4 STANDARDボタン 5 スペアボタン 6 テスト信号出力選択ボタン 2 MEMORY STICKランプ 7 CLOSEボタン 1 メモリースティックスロット 8 VTR START/STOPボタン ゴムキャップ 9 VTR再生制御ボタン PANEL STANDARD ACTIVE TEST BARS CLOSE VTR START/STOP MEMORY STICK AWB ABB WHITE MONITOR FUNCTION VF DISP BLACK MAINTENANCE VF MENU SCENE CANCEL AUTO IRIS/MB IRIS ACTIVE MASTER BLACK PAINT ENTER EXT IRIS ALARM MENU SELECT REMOTE CONTROL UNIT RM-B750 qd ホワイトバランス/ブラック バランス調整部 qa メニュー操作部 0 ALARMインジケーター qs アイリス/マスターブラック調整部 1 メモリースティ
各部の名称と働き メンテナンスメニューのRMコンフィギュレーション(RM Config)メ 9 VTR再生制御ボタン ニューで FULLとLOCK モードのみを切り換えるように変更するこ VTR の再生動作を制御します。 。 ともできます(20(J)ページ) なお、RMコンフィギュレーションメニューは、 どのモードに設定され ていても操作することができます。 s(停止)ボタン 再生、早送り、巻き戻しを停止します。 j(巻き戻し)ボタン 4 STANDARD(標準)ボタン 押して点灯させると、巻き戻しが始まります。 押すとビデオカメラの各種設定が標準状態になり、 ボタンが数秒間 点灯します。 G(再生)ボタン ボタンが点灯している間にもう1度押すと、点灯する前の状態に戻 押して点灯させると、再生が始まります。 ります。 J(早送り)ボタン 5 スペアボタン 将来の機能拡張用です。現在は機能しません。 押して点灯させると、早送りが始まります。 7(記録レビュー)ボタン 押して点灯させると、記録レビューを実行します。 6 テスト信号出力選択ボタン 押して点灯させると、カメラのテスト信
: SCENE(シーンファイル)/CANCEL(キャンセル) qa メニュー操作部 MONITORボタン消灯時は、このボタンを押して点灯させる A RMメニュー選択/カメラメニュー操作ボタン B LCD/タッチパネル と、本機のシーンファイル操作メニューが液晶ディスプレイに表 示されます。 MONITORボタン点灯時は、液晶ディスプレイで選択したカ メラメニュー項目の設定をキャンセルします。 PAINT(ペイント)/ENTER(確定):MONITORボタン消灯時 MONITOR は、このボタンを押して点灯させると、本機のペイントメニュー が液晶ディスプレイに表示されます。 FUNCTION VF DISP MONITORボタン点灯時は、液晶ディスプレイで選択したカ メラメニュー項目の設定を確定します。 MAINTENANCE VF MENU すべてのボタンを消灯させると、ステータス表示(11(J)ページ)に SCENE CANCEL なります。 PAINT ENTER ◆それぞれのメニューの項目については、 「メニュー項目」 (15(J)ページ) をご覧ください。カメラメニューについ
各部の名称と働き qs アイリス/マスターブラック調整部 A AUTO IRIS ボタン AUTO IRIS/MB IRIS B EXTインジ ケーター 9 ホワイトバランス/ブラックバランス調整部 D IRIS/MB ACTIVE インジケーター A AWBボタン E MASTER BLACK つまみ B ABBボタン AWB ACTIVE MASTER BLACK ABB WHITE EXT C WHITEつまみ C IRISつまみ IRIS BLACK D BLACKつまみ A AUTO IRIS(自動絞り)ボタン 押して点灯させると、 レンズの絞りが入力光に応じて自動的に調整 されます。もう1 度押すと消灯し、絞りの手動調整が可能になりま A AWB(ホワイトバランス自動調整)ボタン す。 押すと、ホワイトバランスが自動調整されます。 調整中はボタンが点灯し、調整が完了すると消灯します。 B EXT(レンズエクステンダー)インジケーター 自動調整実行中にもう1度このボタンを押すと、自動調整が中止さ カメラ側でレンズエクステンダーを使用しているとき点灯します。
2 コネクターパネル リモートコントロールケーブルをCAMERA端子に、BNCケーブ ルをMONITOR 端子に差し込む。 1 CAMERA端子 2 MONITOR端子 CA MA RA MO OR NIT カバー固定ネジ BNCケーブル(別売り) リモートコントロールケーブル(付属) 1 CAMERA(カメラ)端子(8ピン) 付属のリモートコントロールケーブルでカメラに接続します。 3 カバーを元通りに閉め、ネジを締める。 2 MONITOR(モニター)端子(BNC型) カメラからの信号をモニターするためのカラーモニターを接続しま す。 接続のしかた RA MA CA OR NIT MO 底面のカバー固定ネジを緩めて、カバーを開ける。 RA MA CA OR NIT MO 1 9 (J)
メニューの構成と基本操作 RM-B750 では、メニュー操作により、システム機器の調整など 2 操作する項目を選択する。 様々な機能に対応します。 メニュー画面の項目ボタンを押し、設定・調整画面または操 作エリアを表示させます。 基本操作手順 メニューが複数ページある場合は ペイントメニューやファンクションメニューのようにメニューが複 数ページある場合は、vまたは Vを押して、必要に応じてメ 本機のメニューを設定する ときは消灯 2 ニューのページを切り換えます。 ◆次ページ「初期画面(ペイントメニュー) 」参照。 サブメニューがある場合は MONITOR ボタンを押して設定・調整画面を切り換えます。 ◆ 12(J)ページ「サブメニュー」参照。 FUNCTION VF DISP 3 MAINTENANCE VF MENU 項目を設定・調整する。 • 設定・調整項目(パラメーター)に対応するつまみを回して SCENE CANCEL (またはボタンを押して) 、希望の値に調整 (希望の設定を選 択)します。 PAINT ENTER ◆ 12(J)ページ「設定・調整画面」参照。
メニュー画面の基本構成 ステータス表示 メニュー操作部でメニュー(FUNCTION、MAINTENANCE、 SCENE、PAINT)を選択しないと(メニュー選択ボタンがすべて 消灯) 、ディスプレイは下図のようなステータス表示になります。 ステータス表示では、各項目は状態表示 のみで、設定はメニューや操作パネルの つまみで行います。 Shutter これらの項目は、ファンクション メニューで設定できます。 シーンファイル操作メニューで 選択したファイル番号が表示さ れます。 60 M. Gain White 0dB 0 0 Gamma ND ND Black 0.45 1 A 0 0 M.
メニューの構成と基本操作 設定・調整画面(ペイントメニュー) ペイントメニューの初期画面で項目を選択すると、画面の下半分が 選択した項目の設定・調整画面になります。 例:ページ2の初期画面でWhiteを選択したとき 2/8 初期画面で選択した項目名が表示されま す。 Gamma Clearを押してからこの部分を押すと、 Clear White 押すと、モニター出力設定画面(次 ページ参照)が上半分に表示されま す。 Black Flare WF/PIX Select 選択した項目の全調整値が標準状態に戻 ります。 White ATW G R 0 B 0 0 調整に関連するON/OFF機能がある 場合は、この列に表示されます。 選択した項目の調整パラメーターおよ び調整値が表示されます。 それぞれに対応する位置の調整つまみ で調整することができます。 Clearを押して調整値を押すと、調整 値が標準状態に戻ります。 サブメニュー 初期画面で選択した項目内で調整パラメーター等が多い場合、サ ブメニューが表示されます。 例:ページ3の初期画面でSkin Detailを選択し
モニター出力設定画面(拡張メニュー) ペイントメニューの設定・調整画面で[WF/PIX Select]を押して点灯 させると、画面上半分にモニター出力設定画面が表示されます。 R/G/B:それぞれR信号、G信号、 B信号を選択します。 RGB:R信号、G信号、B信号を組み WF/PIX Monitor Select R 表示を戻したいときは、もう1度 この項目を押してください。 G B RGB SEQ ENC WF/PIX Select 合わせて選択できます。 SEQ: WF出力のみ有効で、 R、G、 Bの3つの信号の波形をシーケン シャルモードでモニターすること ができます。 ENC:エンコードされた信号が出力 されます。 シーンファイル操作メニュー画面 メニュー操作部の SCENEボタンを押すと、シーンファイル操作メ ニュー画面になります。 シーンファイルの呼び出し: 呼び出したいシーンファイルの番号を選択 して押すと、登録されているファイルが呼 び出されます。 このとき呼び出されているシーンファイル 番号は色が変わります。 同じシーンファイル番号を押すと呼び出さ れる前の状態に
メニューの構成と基本操作 ファンクションメニュー画面 メニュー操作部の FUNCTIONボタンを押すと、ファンクションメ ニュー画面になります。 Operation選択時 v/Vを押して希望するフィルターを選択します。 NDフィルター、CCフィルターの枚数はカメラに依存します。 Operation Filter Ctrlを押して色を変えると この画面でフィルターを選択でき る状態になります。 SW Filter ND Ctrl 1 Shutter 60 WHITE CC Gamma A 0.45 v/Vを押してガンマ値を選択します。 ±0.05ステップで変更できます。 Master Gain ECS 30.
メニュー項目 操作/調整項目欄で●が付いている項目は調整つまみに割り当て られる項目、それ以外の項目は、メニュー画面上で操作する項目 です。 ペイントメニュー ペイントメニューは 8 ページで構成されています。 各ページのv/Vを押すことによって、ページ1∼8を順次切り換え ることができます。 ページ Paint 1/8 メニュー サブメニュー 操作/調整項目 機能 Detail 1 HDa) ● Level HD ディテールレベル調整 ● Limiter HD ディテールリミッター調整 ● Crispening HD ディテールクリスプニング調整 ● Level HDレベルディペンド調整 SDa) Dep Detail Off HD ディテール ON/OFF SD DTL Off SD ディテール ON/OFF ● Level SD ディテールレベル調整 ● Limiter SD ディテールリミッター調整 ● Crispening SD ディテールクリスプニング調整 ● Level Dep Detail Off Skin Detail Flar
メニューの構成と基本操作 ページ メニュー Paint 3/8 V Mod Saw Skin Detail サブメニュー 1/2/3(項目共通) Saturation Black Gamma Paint 4/8 Detail 1 操作/調整項目 機能 ● R/G/B/Master V モジュレーション調整 V Mod Saw Off V モジュレーションON/OFF ● Level スキンディテールレベル調整 ● Phase スキンディテール色相調整 ● Width スキンディテール色相幅調整 ● Saturation スキンディテールサチュレーション調整 DTL Gate # スキンディテールゲートON/OFF(チャンネル別) Auto Hue # スキンディテールオートヒュー(チャンネル別) Skin DTL # スキンディテール ON/OFF(チャンネル別) ● Saturation サチュレーション調整 Saturation サチュレーションON/OFF RGB ● R/G/B/Master ブラックガンマ調整 Y ●Y
メニュー サブメニュー 操作/調整項目 機能 Paint 4/8 Detail 3 SDa) ● W.Limiter SD ディテールホワイ トリミッター調整 (続き) (続き) ● B.Limiter SD ディテールブラックリミッター調整 ● Coring SDクロスカラーレデュースコアリング調整 ● Level SDクロスカラーレデュースレベル調整 Crs Col Reduce SDクロスカラーレデュースON/OFF ぺ−ジ Cross Color Suppression ● CCS ● N.
メニューの構成と基本操作 ぺ−ジ メニュー Paint 7/8 Gamma Table サブメニュー Auto Knee Auto Iris ECS/S-EVS Paint 8/8 SD Gamma 操作/調整項目 機能 ● Standard ガンマテーブル設定 ● User ユーザーガンマテーブル設定 Standard 標準ガンマテーブル選択 User ユーザーガンマテーブル選択 Gamma Off ガンマON/OFF ● Point Limit オートニー時のニーポイントの下限値設定 ● Auto Slope オートニー時のニースロープ調整 Adaptive アダプティブハイライトコントロール ON/OFF Knee Off ニーON/OFF ● Phase スキントーンオートアイリス色相調整 ● Width スキントーンオートアイリス色相幅調整 Normal Mode オートアイリスノーマルモード選択 Skin Mode オートアイリススキンモード選択 Iris Auto Hue オートヒュー調整 Auto Iris
メンテナンスメニュー 1次メニュー 2次メニュー サブメニュー 操作/調整項目 Adjusting Black Shading R/G/B ●H White Shading R/G/B Auto B Shading Phase H Phase SC Phase Auto Iris ●H オートブラックシェーディング調整 Saw/H Para/V Saw/V Para ホワイ トシェーディング調整 Auto W Shading オートホワイ トシェーディング調整 ●H Step H 位相の調整 ●H Coarse ●H Fine ● SC SC 位相の調整 ● BF ブラックバースト信号位相の調整 ●(パターン) オートアイリスパターンの選択 ● Level オートアイリスレベル調整 ● APL ● Iris Auto Setup 機能 Saw/H Para/V Saw/V Para ブラックシェーディング調整 Ratio Gain オートアイリスAPLレシオ調整 オートアイリスゲイン調整 Auto White ホワイ トバラン
メニューの構成と基本操作 1次メニュー 2次メニュー サブメニュー 操作/調整項目 機能 RM Config Date ● Year 本機内蔵の時計の日付合わせ Date/Time (続き) ● Month ● Day Set Cancel Time ● Hour 本機内蔵の時計の時刻合わせ ● Minute ● Second Set Cancel SW Setting Active Mode Setting Active Mode PANEL ACTIVEボタンの動作モードの切り換え Mode2:FULL/LOCK Mode3:FULL/PART/LOCK TEST TEST Mode TESTボタンを押すと出力される信号(Saw、3STEP、 10STEP)の選択 VTR START/STOP SW Mode VTR START/STOPボタンの機能(VTR 機能、 CALL 機能)の選択 Cable Comp VR Setting White R/B Black R/B Master Black IRIS Length ビデオ信号を利用する際
ファンクションメニュー メニュー サブメニュー Operation SW page 1 操作/調整項目 機能 Filter Ctrl フィルターリモート/ローカルモードの選択 ND (1/2/3/4/5) NDフィルターの選択 CC (A/B/C/D/E) CCフィルターの選択 Gamma ステップガンマの選択 Master Gain マスターゲインの選択 Shutter シャッターモードの ON/OFF ECS ECS モードのON/OFF ● Shutter シャッタースピードの選択 ● ECS ECS 周波数の選択 5600K 5600K の電気色温度補正機能のON/OFF Auto Knee オートニー機能のON/OFF。ON では、ハイライ トが入ると自動的にニーが働く。 Skin Detail 肌色部分(顔など)のディテールを抑制するスキントーンディテール機能のON/OFF Detail Gate スキントーンディテールゲート機能のON/OFF。 ON では、スキントーンディテールの調整範囲がモニター上に白く表示される。 page
初期設定 LCD設定画面を表示させるときは、[LCD]を押す。 RM-B750の動作環境の設定 LCD 設定画面(24(J)ページ)に切り換わります。 メンテナンスメニューのRMコンフィギュレーションメニューやLCD 設定画面では、RM-B750に内蔵されている時計の時刻合わせや、 警告ブザー音の音量、 インジケーターやディスプレイの明るさを調整 時計を合わせる することもできます。 RM-B750には、メモリースティックにリファレンスファイルやシーン RMコンフィギュレーションメニュー/LCD設定 ファイルを保存した日時を記録するための時計が内蔵されていま 画面を表示させるには す。 時計合わせは、次の手順で行います。 次の手順で操作します。 1 本機のメニューを設定する ときは消灯 RMコンフィギュレーションメニューの[Date/Time] を押す。 時計合わせメニューに切り換わり、現在の設定が表示されま す。 MONITOR Maintenance Menu Adjusting FUNCTION VF DISP 1 Auto Setup Date Time Se
3 2 時刻を合わせる。 [Buzzer Volume]を押して点灯させる。 1) [Time]を押して点灯させる。 ディスプレイの下半分が、ブザー設定画面になります。 Date Time Setting Exit Clear 2001/11/17 (Sat) 22 : 12 : 31 Date Time Hour Minute Second 32 25 17 Set Exit Buzzer Volume LED Bright Call Buzzer Call Buzzer Volume Touch SW Click Click Touch Switch Cancel 50 50 50 All Off Master 50 2) 左 の 3 つ の 調 整 つ まみ で そ れ ぞ れ 時( Hour)、分 (Minute) 、秒(Second)を合わせる。 対応する調整つまみで、ブザーの音量を調整する (標準設定 値はすべて 50) 。 設定した時刻が有効になります。 Call:コール信号受信時のブザーの音量 Touch:メニュー画面(タッチパネル)に
メニューの構成と基本操作 LEDの明るさを設定する 液晶ディスプレイの明るさを設定する RM-B750 では、操作ボタンやインジケーターの LED の明るさを調 LCD設定画面で、 メニュー操作部の液晶ディスプレイの明るさを調 整できます。 整できます。 1 1 RMコンフィギュレーションメニューの[RM Adjusting]を押して、 RM 設定メニューに切り換える。 2 メンテナンスメニューの[LCD]を押して、LCD設定画面に切り 換える。 RM 設定メニューの[LED Bright]を押して点灯させる。 Clear Exit ディスプレイの下半分が、LED 明るさ設定画面になります。 LCD Brightness Clear Buzzer Volume Exit LED Bright Bright 50 LED Brightness Switch 50 Other 50 Master 50 2 左端の調整つまみで、Bright(明るさ)を調整する(標準設定 値は 50) 。 3 対応する調整つまみで、LEDの明るさを調整する(標準設定 値はすべて
メモリースティック メモリースティックの取り付け メモリースティックについて 別売りのメモリースティックを使用すると、 ファイル情報を保存し、 他のリモートコントロールユニットでも同じファイル情報を共有するこ とができます。 メモリースティックとは? メモリースティックは、小さくて軽く、 しかもフロッピーディスクより 容量が大きい新世代のIC記録メディアです。メモリースティック メモリースティックを取り付けるには ゴムキャップをはずし、ラベル面を手前にして、端子を奥に向けて 対応機器間でデータをやりとりするのにお使いいただけるだけでな く、着脱可能な外部記録メディアの1つとしてデータの保存にもお 使いいただけます。 メモリースティック装着部に差し込みます。 カチッと音がして、ア クセスランプが赤く点灯するまで差し込んでください。 メモリースティックの種類 メモリースティックには、著作権保護技術(マジックゲート)を搭 ラベル面 載した“マジックゲートメモリースティック” と、搭載していない一般 の“メモリースティック”の2種類があります。 本機では“マジックゲートメモリースティック”と一般
メモリースティック メモリースティックの取り扱いについてのご注意 • 以下の場合、データが破壊されることがあります。 ― 読み込み中、書き込み中にメモリースティックを抜いたり、 本機の電源を切った場合 ― 静電気や電気的ノイズの影響を受ける場所で使用した場合 大切なデータはバックアップを取っておくことをお奨めします。 • 端子部に触れたり、金属を接触させたりしないでください。 • ラベルの貼り付け部には、専用ラベル以外は貼らないでください。 • ラベルを貼るときは所定のラベル貼り付け部に貼ってください。 は みださないようにご注意ください。 • 強い衝撃を与えたり、曲げたり、落したりしないでください。 • 分解したり、改造したりしないでください。 • 水にぬらさないでください。 • 以下のような場所でのご使用や保管は避けてください。 ― 高温になった車の中や炎天下などの気温の高い場所 ― 直射日光のあたる場所 ― 湿気の多い場所や腐食性のある場所 • 持ち運びや保管の際は付属の収納ケースに入れてください。 • RM-B750 で使用できる容量のメモリースティックは、カメラ側 では 使用できない場合があります
主な仕様 一般 電源 DC10.5∼ 30 V 消費電力 最大 4 W 最大ケーブル長 50 m 動作温度 5℃∼ 40℃ 最大外形寸法 197 × 124 × 62 mm (幅 / 高さ/ 奥行き) 質量 0.
English To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. AVERTISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité. Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.
Table of Contents Overview ............................................................................................... 3(E) Features .......................................................................................... 3(E) Locations and Functions of Parts ....................................................... 4(E) Operation Panel .............................................................................. 4(E) Connector Panel .....................................................................
Overview The RM-B750 Remote Control Unit is designed for remote control of Sony BVP/HDC-series CCD color video cameras. Using the supplied special cable, the unit can be directly connected to the camera to control it from a distance of up to 50 m (164 feet). Features The principal features of the RM-B750 are as follows: Controlling the S-EVS function of the camera The vertical resolution for the Super EVS (Enhanced Vertical-Definition System) can be adjusted from this unit.
Locations and Functions of Parts Operation Panel 3 PANEL ACTIVE button 4 STANDARD button 5 Spare button 6 Test signal output select buttons 2 MEMORY STICK lamp 7 CLOSE button 1 Memory Stick slot 8 VTR START/STOP button Rubber cap 9 VTR playback control buttons PANEL STANDARD ACTIVE TEST BARS CLOSE VTR START/STOP MEMORY STICK AWB ABB WHITE MONITOR FUNCTION VF DISP BLACK MAINTENANCE VF MENU SCENE CANCEL AUTO IRIS/MB IRIS ACTIVE MASTER BLACK PAINT ENTER EXT IRIS ALARM MENU SELECT REMOTE
Using the RM Configuration menu under the Maintenance menu, the function of this button can be changed to switch only between FULL and LOCK modes (see page 19(E)). The RM Configuration menu operation is possible in any mode. 4 STANDARD button When you press this button, the video camera is initialized to its standard state, and the button lights for several seconds. If you press the button while lit, the video camera retrieves the state before the button was lit. 5 Spare button For future use.
Locations and Functions of Parts qa Menu operation block A RM menu select/camera menu set buttons B LCD/touch panel MONITOR FUNCTION VF DISP MAINTENANCE VF MENU SCENE CANCEL For the items of each menu, see “Menu Items” on page 14(E). For details on the camera menus, refer to the Operation Manual or the System Manual for the camera.
qd White balance/black balance control block qs Iris/master black control block A AWB button D IRIS/MB ACTIVE indicator B ABB button A AUTO IRIS button AUTO IRIS/MB IRIS ACTIVE MASTER BLACK E MASTER BLACK control AWB ABB WHITE B EXT indicator C WHITE controls EXT C IRIS control BLACK IRIS D BLACK controls A AUTO IRIS button Press and light the button to automatically adjust the iris according to the amount of input light.
Locations and Functions of Parts 2 Connector Panel Connect the remote control cable to the CAMERA connector and the BNC cable to the MONITOR connector. 1 CAMERA connector 2 MONITOR connector CA MA RA MO OR NIT Cover fixing screw BNC cable (sold separately) 1 CAMERA connector (8-pin) Connect to the camera using the supplied remote control cable. Remote control cable (supplied) 3 Close the cover and secure the screw.
Menu Configuration and Basic Menu Operations The RM-B750 provides menu operations for various functions such as adjustments of system equipment. 2 Press the button that shows the name of the item on the menu to obtain the corresponding adjustment display or operation area. Basic Operating Procedure Unlit when setting the menus of this unit. Select the item to be adjusted.
Menu Configuration and Basic Menu Operations Basic Configuration of Menu Display Status display When you do not select any of the Menu select buttons (FUNCTION, MAINTENANCE, SCENE, PAINT) of the menu operation block (all unlit), the LCD shows the following status display: On the status display, each item is only displayed. The setting is made with the menu or with the corresponding knob on the operation panel. Shutter You may set these items using the Function menu.
Adjustment display (Paint menu) When you select an item on the initial display of the Paint menu, the lower half of the panel becomes the adjustment display for the selected item. Example: when you select “White” from the initial display of page 2 White When you press this, the upper half of the panel becomes the monitor output setting display (see the next page). The name of the item selected on the initial display is displayed.
Menu Configuration and Basic Menu Operations Monitor output set display (Expansion menu) When you press [WF/PIX Select] on an adjustment display of the Paint menu, the upper half of the panel becomes the monitor output setting display. WF/PIX Monitor Select R Press again to return to the previous display. G B RGB SEQ ENC WF/PIX Select R/G/B: To independently select the R, G, or B signal. RGB: To select the R, G, and B signals in combination.
Function menu displays When you press and light the FUNCTION button of the menu operation block, the Function menu display is obtained. When “Operation” is selected Press v or V to select the desired filter. The number of ND and CC filters you may select depends on the camera. Operation Press [Filter Ctrl] and change its color to enable filter selection from this display. SW Filter ND Ctrl 1 Shutter 60 WHITE CC Gamma A 0.45 Press v or V to set the gamma value. You may change it in ±0.05 steps.
Menu Configuration and Basic Menu Operations Menu Items The “Control items” marked with z are those assigned to the control knobs. The other items are operated on the menu display. Paint menu Paint menu consists of pages 1 to 8. Pressing v or V of each page flips pages 1 through 8 in sequence. Page Paint 1/8 Menu Detail 1 Submenu HD a) SD a) Skin Detail 1/2/3 (common) Control item z Level Adjusts the HD detail level. z Limiter Adjusts the HD detail limiter.
Page Menu Paint 3/8 V Mod Saw Submenu Control item z R/G/B/Master V Mod Saw Off Skin Detail 1/2/3 (common) Paint 4/8 Detail 1 z Phase Adjusts the skin detail phase. z Width Adjusts the skin detail width. z Saturation Adjusts the skin detail saturation. Turns the skin detail gate ON/OFF (each channel). Auto Hue # Executes the skin detail auto hue setup (each channel). Saturation Turns the skin detail ON/OFF (each channel). Adjusts the saturation. Turns the saturation ON/OFF.
Menu Configuration and Basic Menu Operations Page Menu Submenu Paint 4/8 (Continued) Cross Color Suppression Control item z CCS Level Adjusts the level for cross color suppression. z N. Level Adjusts the notch level. z Frequency Adjusts the notch frequency.
Page Menu Paint 7/8 (Continued) Auto Iris ECS/S-EVS Submenu Control item z Phase Adjusts the skin tone auto iris phase. z Width Adjusts the skin tone auto iris width. Normal Mode Selects Normal mode for auto iris. Skin Mode Selects Skin mode for auto iris. Iris Auto Hue Executes the auto hue. Auto Iris Gate Turns the skin tone auto iris gate ON/OFF. z Shutter Adjusts the shutter speed. z ECS Adjusts the ECS frequency. z S-EVS Adjusts the Super EVS.
Menu Configuration and Basic Menu Operations Maintenance menu Menu 2ndary menu Submenu Control item Adjusting Black Shading R/G/B z White Shading R/G/B H Saw/H Para/V Saw/V Para Auto B Shading z H Saw/H Para/V Saw/V Para Auto W Shading Phase H Phase SC Phase Auto Iris Auto Setup Function Adjusts the black shading. Executes the auto black shading. Adjusts the white shading. Executes the auto white shading. z H Step z H Coarse z H Fine z SC Adjusts the SC phase.
Menu 2ndary menu Submenu Control item RM Config (Continued) Date/Time Date z Year z Month z Day Function Adjusts the date for the built-in clock of this unit. Set Cancel Time z Hour z Minute z Second Adjusts the time for the built-in clock of this unit. Set Cancel SW Setting Active Mode Setting Active Mode Switches the mode of the PANEL ACTIVE button. Mode 2: FULL/LOCK Mode 3: FULL/PART/LOCK.
Menu Configuration and Basic Menu Operations Function menu Menu Submenu Operation Control item Function Filter Ctrl Selects the filter remote or local mode. ND (1/2/3/4/5) Selects ND filters. CC (A/B/C/D/E) Selects CC filters. Gamma Selects the step gamma. Master Gain Selects the master gain. Shutter Turns the shutter mode ON/OFF. ECS SW page 1 Turns the ECS mode ON/OFF. z Shutter Selects the shutter speed. z ECS Selects the ECS frequency.
Initial Settings To obtain the LCD setting display, press [LCD]. Setting the Operating Conditions of the RM-B750 By using the RM Configuration menu or LCD setting display, you can set the built-in clock of the RM-B750 and adjust various conditions of the RM-B750, such as the sound volume of the warning buzzer and the brightness of the indicators and LCD. To display the RM Configuration menu/ LCD setting display The LCD setting display (page 23(E)) appears.
Initial Settings 3 2 To set the time: 1) Press and light [Time]. Date Time Setting Press and light [Buzzer Volume]. The lower half of the display becomes the Buzzer Volume adjustment display. Exit Clear 2001/11/17 (Sat) 22 : 12 : 31 Buzzer Volume Date Time Hour Minute Second 32 25 17 Set Buzzer Volume Cancel Call Buzzer Call 50 2) Set the Hour, Minute and Second with the left three control knobs. 3) Press [Set] in synchronization with a time signal. The set time becomes valid.
Adjusting the Brightness of the LEDs Adjusting the Brightness of the LCD You can adjust the brightness of the LEDs of the panel buttons and indicators. To adjust the brightness, proceed as follows: You can adjust the brightness of the display of the menu control block. Proceed as follows: 1 Press [RM Adjusting] on the RM Configuration menu to display the RM adjustment menu. 1 2 Press and light [LED Bright]. Press [LCD] on the Maintenance menu to display the LCD setting display.
Memory Sticks Using a Memory Stick Notes on Memory Stick When a Memory Stick is inserted in the unit, the file data can be stored on the Memory Stick, which enables you to share data among RM units. Inserting a Memory Stick Open the rubber cap and insert a Memory Stick with the label side to the front into the Memory Stick slot until it clicks and the access lamp lights in red.
Handling of Memory Stick • Image data may be damaged in the following cases: – If you remove the Memory Stick, or turn the power off when the access lamp is lit in red – If you use a Memory Stick near static electricity or a magnetic field We recommend backing up important data. • Prevent metallic objects or your finger from coming into contact with the terminal of the connecting section. • Do not attach any material other than the supplied label to the label space.
Specifications General Power requirements 10.5 to 30 V DC Power consumption 4 W max. Maximum cable length 50 m (164 feet) Operating temperature 5°C to 40°C (41°F to 104°F) Dimensions (w/h/d) 197 × 124 × 62 mm (7 7/8 × 5 × 2 1/2 inches) Mass 0.
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
Sony Corporation RM-B750(SY) 3-620-577-01(1) B&P Company Printed in Belguim 2002.07.