3-709-285-12 (1) Black and White Monitor Operating Instructions Mode d'emploi Page 12 SSM-175A © 1997 by Sony Corporation Page 2
English Owner’s Record This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No.
CAUTION: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Table of Contents Before operating the unit, please read this manual thoroughly and retain it for future reference. Features .............................................................................. 4 Precautions ......................................................................... 5 Location and Function of Controls .................................. 6 Front Panel ...................................................................... 6 Rear Panel ..................................................
Precautions Safety Cleaning • The unit operates on 120 V AC, 60 Hz. • Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further. • Unplug the unit from the wall outlet if it is not going to be used for several days or more. To disconnect the cord, pull it out by the plug. Never pull the cord itself. • Allow adequate air circulation to prevent internal heat build-up.
Location and Function of Controls 1 INPUT select switch Keep this switch released (øA) to monitor the signal from the VIDEO A IN connector. Depress this switch (ØB) to monitor the signal from the VIDEO B IN connector. Front Panel 2 3 2 H-HOLD (horizontal hold) control When the picture has slanting horizontal bars, turn the HHOLD control in either direction until a stationary picture is obtained.
VIDEO A connectors and 75Ω ON/OFF switch Rear Panel 8 VIDEO B connectors and 75Ω ON/OFF switch Two video input connectors (VIDEO A and VIDEO B) for the composite video signals and their loop-through output connectors. To monitor the signals input to the VIDEO A IN connector, keep the INPUT select switch released (øA). To monitor the signals input to the VIDEO B IN connector, keep the INPUT select switch released (ØB).
Connections Connecting a Video Camera or a VCR Connect the VIDEO IN connector to the video output of a video camera or a VCR.
Connecting the Monitors Using the loop-through feature of this unit, the same picture can be obtained on all the monitors connected. You can connect up to three monitors. Adjust the picture contrast and brightness of each monitor.
Specifications General System Picture tube EIA standard 17-inch picture measured diagonally 90-degree deflection Resolution More than 850 TV line (horizontal) Video input Composite: 0.5 – 2 Vp-p, sync negative (×2) Video input impedance High impedance for loopthrough; 75Ω terminated Video output Composite: 0.
Français Avant d’utiliser le moniteur, veuillez lire attentivement ce manuel et le conserver à titre de référence ultérieure. AVERTISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité. Des courants de hautes tensions dangereuses sont présents à l’intérieur de cet appareil. Ne pas ouvrir le coffret. Se reporter à un personnel qualifié uniquement. Cet appareil n’est pas conçu pour être utilisé avec un ordinateur.
Précautions Entretien • L’appareil fonctionne sur courant alternatif en 120 V (60 Hz). • Si un liquide ou objet quelconque venait à s’introduire dans l’appareil, débranchez immédiatement le cordon d’alimentation et faites vérifier l’appareil par un technicien qualifié avant de le remettre en service. • Débranchez l’appareil si vous ne comptez pas l’utiliser pendant plusieurs jours ou davantage. Débranchez le cordon d’alimentation en tirant sur la fiche, jamais sur le cordon lui-même.
Localisation des commandes 1 Touche de sélection de l’entrée (INPUT) Maintenez cette touche sortie (øA) pour recevoir le signal provenant de l’entrée VIDEO A IN, et enfoncée (ØB) pour recevoir le signal provenant de l’entrée VIDEO B IN. Panneau avant 2 Commande de synchronisation horizontale (H-HOLD) Ce bouton permet, en le tournant dans le sens approprié, de stabiliser le défilement horizontal de l’image.
7 Entrée/sortie VIDEO A et touche de marche/arrêt 75 Ohms (ON/OFF) Panneau arrière 8 Entrée/sorie VIDEO B et touche de marche/arrêt 75 Ohms (ON/OFF) Deux entrées vidéo (VIDEO A et VIDEO B) et deux sorties pour le fonctionnement en boucle. Maintenez la touche de sélection de l’entrée (INPUT) sortie (øA) pour recevoir le signal provenant de l’entrée VIDEO A IN. Maintenez la touche de sélection de l’entrée (INPUT) enfoncée (ØB) pour recevoir le signal provenant de l’entrée VIDEO B IN.
Raccordements Raccordement avec une caméra vidéo ou un magnétoscope Raccordez la sortie de la caméra ou du magnétoscope et l’entrée du moniteur (VIDEO IN).
Raccordement de plusieurs moniteurs La fonction boucle de cet appareil permet d’obtenir la même qualité d’image sur tous les moniteurs reliés. Vous pouvez relier jusqu’à trois moniteurs. Réglez le contraste et la luminosité de chanque moniteur.
Caractéristiques techniques Caractéristique Système Tube image Standard EIA Diagonale d’image: 17 pouces Déflexion: 90 degrés Résolution Supérieure à 850 lignes télévision (Horizontale) Entrée vidéo Composée: 0,5 – 2 Vcc, synchro négative (×2) Impédance entrée vidéo Haute impédance en fonctionnement en boucle; sortie 75 Ohms Sortie vidéo Composée: 0,5 – 2 Vcc, synchro négative (×2) Impédance sortie vidéo Supérieure à 10 kOhms Alimentation électrique 120 V A/C, 60 Hz Consommation électrique Env. 35 W Temp.
Sony Corporation Printed in Korea