HD CAMERA CONTROL UNIT HDCU-950 SD ENCODER UNIT HKCU-951 HD FRAME RATE CONVERTER UNIT HKCU-953 INSTALLATION AND MAINTENANCE MANUAL 1st Edition (Revised 3) Serial No. 10001 and Higher : HDCU-950 Serial No. 10001 and Higher : HKCU-951 Serial No.
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.
For HDCU-950 For HDCU-950 Laser Diode Properties Material : In GaAsP Wave length : 1310 ± 40 nm Emission duration : Continuous Laser output power: _8 dBm Attention-when the product is installed in Rack: For HDCU-950 2. Providing protective earth When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection.
Table of Contents Manual Structure Purpose of this manual ........................................................................................ 3 (E) Related manuals ................................................................................................... 3 (E) Contents ............................................................................................................... 4 (E) Trademark ....................................................................................................
2. System Setup 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. System Connection ................................................................................ 2-1 (E) 2-1-1. Standard System ................................................................... 2-2 (E) 2-1-2. Standard HD/SD System ...................................................... 2-3 (E) 2-1-3. HD/SD Film Like System .................................................... 2-4 (E) 2-1-4. Analog NTSC/PAL System .........................................
Manual Structure Purpose of this manual This manual is the installation and maintenance manual of the following models : HD Camera Control Unit HDCU-950 SD Encoder Unit HKCU-951 HD Frame Rate Converter Unit HKCU-953 This manual is intended for use by trained system and service engineers, and describes the information regarding the installation of the unit and the information required for initial service.
Contents The following is a summary of the sections of this manual. Section 1 Installation Overview Describes how to checking the ROM version, connectors and cables, setting of switches on boards, function of the indicators on boards, installing in 19-inch rack, etc. Section 2 System Setup Describes how to set and adjust when connecting the unit to the camera system. Section 3 Service Overview Describes recommended replacement parts, how to cleaning connector/cables and charactor display function.
Section 1 Installation Overview 1-1. Checking the ROM and Software Version When connecting the following peripheral equipment to the unit, confirm that the versions of the ROMs and software which are installed in each model. If the version is lower than the following one, the ROM needs to be replaced and the software needs to be upgraded. In this case, contact your local Sony Sales Office/Service Center. ROM Peripheral equipment Board Ref. No. ROM version MSU-700A CPU-293 IC5, IC6 Ver. 1.
1-3. Power Cord 1-4. Matching Connectors and Cables 1-3. Power Cord 1-4. Matching Connectors and Cables w The power cord is not supplied with this unit. Be sure to use the specified power cord. Do not use the damaged power cord. 1-4-1. Connector Input/Output Signal BNC Connector HDCU-950 For U.S.A. and Canada 1 Power cord 125 V 10 A (2.4 m) : ! 1-551-812-11 2 Plug holder (black) : 2-990-242-01 1 2 AC inlet 1125 digital signal RET (1 to 3) IN : BNC Conforms to BTA-S004B, 1.485 Gbps/1.
1-4. Matching Connectors and Cables HKCU-951 (525/625 analog signal) CAMERA connector (optical/electrical composite connector) Y/G OUT : BNC Y : 1.0 V p-p (video: 0.714 V, sync : 0.286 V ), 75 Z G : 0.7 V, 75 Z VIDEO B-Y/B OUT : BNC B-Y : 0.756 V p-p, 75 Z (when 75 % color bar is input) B : 0.7 V, 75 Z R-Y/R OUT : BNC R-Y : 0.756 V p-p, 75 Z (when 75 % color bar is input) R : 0.7 V, 75 Z VBS OUT : BNC 1.0 V p-p, 75 Z Y/PB/PR Conforms to BTA-S004B, 1.485 Gbps/ 1.
1-4. Matching Connectors and Cables MIC1/MCI2 (XLR 3-pin, Male) 1 *1 : CHU MIC 1/2 AMP GAIN 2 3 _ EXT VIEW _ (0 dBu = 0.775 Vrms) No.
1-4. Matching Connectors and Cables INCOM/TALLY/PGM (D-sub 25-pin, Female) 13 WF MODE (4-pin, Female) 1 25 4 1 3 2 14 _ EXT VIEW _ _ EXT VIEW _ (0 dBu = 0.775 Vrms) No. Signal Specifications 1 SEQ CONT OUT (G) OPEN COLLECTOR No.
1-4. Matching Connectors and Cables INCOM (5-pin, Female) Connector 1 5 4 3 2 Connector/cable HDCU-950 1-569-370-12 PLUG, BNC or RET IN (1-3) BELDEN8281 Cable or SERIAL OUTPUT (1-2, MONI) equivalent SD SDI OUT (1-3) _ EXT VIEW _ (0 dBu = 0.775 Vrms) No. Signal Specifications 1 INCOM (T) IN (Y) _20 dB 2 INCOM (T) IN (X) (CARBON MIC) _40 dB (ECM MIC) _60 dB (DYNAMIC MIC) 3 INCOM (T) IN (G) GND for INCOM 4 INCOM (R) OUT (X) Max. 12 dBu 5 NC No connection 1-4-2.
1-5. Circuit Boards Layouts 1-5.
1-6. Setting of Switches on Boards 1-6. Setting of Switches on Boards 1-6-1. AT-149 Board A B C D E F G H J K 1 AT S409 S403 S410 S406 S416 S407 S417 3 S427 HD REM BB H PHASE STEP COARSE ADV S405 S423 S424 4 S428 S422 S421 5 S411 UN LOCK S202 REF IN S402 S412 S413 REFERENCE S419 90H S408 S420 2 S404 S414 /1.001 S418 POWER DELAY AT-149 board (A side/panel side) n Do not change the settings of the switches described “Factory use only” and unused switches. .
1-6. Setting of Switches on Boards . S408 (MARKER REMOTE/LOCAL SEL) Selects either the HDCU-950 or the RCP/MSU connected outside in order to control the aspect marker and skin gate signal to be inserted in the HD SDI MONITOR output signal and in the PIX output signal that are output from the MONI connector on the rear panel. REM : Control is performed by RCP/MSU etc., connected outside. LOC : Control is performed by the switches (S402, S403, S409 and S410) on the AT-149 board. Factory setting : REM .
1-6. Setting of Switches on Boards Factory setting : 60V (S418) INTR (S419) FORMAT S420 S418 S419 1080/60 (or 59.94) i 1.000 60V (or 1.001) INTR 1080/30 (or 29.97) PsF 1.000 60V (or 1.001) PROG 1080/50i 1.000 50V INTR 1080/25PsF 1.000 50V PROG 1080/24 (or 23.98) PsF 1.000 48V (or 1.001) PROG 540/60 (or 59.94) PsF 1.000 60V (or 1.001) 540P n 540P and the formats other that what are describe above, are not supported at present. . S420 (FRAME FREQ.
1-6. Setting of Switches on Boards 1-6-2. AU-281 Board (Front Panel) CABLE ALRAM POWER CAM OPEN MAIN SHORT S1 S3 INCOM MIC-ON OFF PGM PROD PRIV . S4 (TALK GAIN) Sets the microphone input level according to the type of headset microphone to be connected to the INCOM connector on the front panel.
1-6. Setting of Switches on Boards 1-6-3. AVP-4 Board A B C D E F G H J K 1 S15 AVP POWER S16 S1 INTERCOM PGM1 MIX 2 S501 S11 PGM2 S500 PGM1 LEVEL S12 PGM2 LEVEL SIDE TONE S14 3 S503 2WIRE CANCEL PROD ENG MIC LEVEL NORM MIC1 MIN NORM MIC2 MIN S710 S711 4 S2 S610 S611 5 S3 S502 S103 S101 S102 S100 AVP-4 board (A side/panel side) n Do not change the settings of the switches described “Factory use only”. .
1-6. Setting of Switches on Boards . S15 (MIC DELAY) This switch is used to match the amount of delay of MIC and AES/EBU format audio signal with the video signal. About 5 msec. is delayed per one step. Example) : 7 : 1 FRAME DELAY (30 FRAME/SEC) 8 : 1 FRAME DELAY (25 FRAME/SEC) Factory setting : 0 . S16-1 to 8 Factory use only Factory setting : All OFF . S100 (R TALLY POWER/CONTACT) .
1-6. Setting of Switches on Boards 1-6-4. DRX-1 Board A B C D E F G H J K 1 DRX POWER 60 2 50 S204 48 PsF S206 3 S202 540P S201 4 CHARACTER REW FF S205 5 S203 DRX-1 board (A side/panel side) n Do not change the settings of the switches described “Factory use only”. . S201 (GRAY ON/OFF) When you turn off the power of the camera or when the communication with the camera is cut, this switch selects the signal to be output from the CCU.
1-6. Setting of Switches on Boards . S206 Factory setting : All OFF -1, 2 Factory use only -3 (MAIN/MONI CHANGE) When this switch is set to ON, the character signal and the marker signal are mixed with the all output signals except the HD-SDI-MONITOR output. ON : Change mode OFF : Normal mode -4 (MONI CHARACTER OFF) Selects whether the character signal and the marker signal are mixed or not to the signal to be output from the MONI connector on the rear panel.
1-6. Setting of Switches on Boards 1-6-5. DTX-1 Board A B C D E F G H J K 1 DTX POWER OPTICAL CONDITION CCU S607 S608 2 S610 CHU S606 3 S603 CHU LOCK RETURN SET HD REM SD 4 S604 5 S601 S605 DTX-1 board (A side/panel side) n Do not change the settings of the switches described “Factory use only”. . S601 (SD RETURN FORMAT) Selects the signal format that is input to the RET1 to 3 connectors on the rear panel when S605 on the DTX-1 board is set to SD.
1-6. Setting of Switches on Boards . S605 (RETURN SET) Sets the format of the return signal to be input to the RET1 to 3 connectors on the rear panel. HD : Sets the RET1 to 3 to the HD-SDI. SD : Sets the RET1 to 3 to SD. (Depends on the setting of S601, S603 and S604 on the DTX-1 board.) REM : Sets the format of each return signal from RM/ MSU, etc. connected outside. Factory setting : REM .
1-6. Setting of Switches on Boards 1-6-6. RC-91 Board A B C D E F G H J K 1 RC POWER 525 S4 S2 S1 S3 2 625 S6 REM LOCAL S5 3 S7 S11 4 S8 S10 SQ LB EC CENT VAR S301 S9 RIGHT 5 LEFT RC-91 board (A side/panel side) n Do not change the settings of the switches described “Factory use only” and unused switches. . S1 (SET-UP ON/OFF) Selects whether SETUP is added or not to the VBS signal to be output from PIX OUT/WF OUT connector on the rear panel.
1-6. Setting of Switches on Boards . S8 (EC POSITION SEL) This switch is valid when S6 on the RC-91 board is set to LOCAL. When S7 on the RC-91 board is set to EC or LB, and S10-3 and S10-4 on the RC-91 board are set to 13 : 9, 14 : 9, or 15 : 9, select the cutting position. CENT : Cuts out the center. VAR : Changes the horizontal cutting position with S9 on the RC-91 board. Factory setting : CENT . S9 (EC POSITION CONT) This switch is valid when S6 on the RC-91 board is set to LOCAL.
1-6. Setting of Switches on Boards 1-6-7. EN-145 Board (HKCU-951) A B C D E F G H J K 1 EN POWER S401 S402 VBS 2 S101 LEVEL S103 SYNC CHROMA COMPONENT R/R-Y G/Y S104 3 S102 4 B/B-Y S106 S107 S201 SC PHASE ADV DELAY S105 5 EN-145 board (A side/panel side) n Do not change the settings of the switches described “Factory use only” and unused switches. . S101 (SD ANA OUT RGB/YCD) Selects the signal that is output from the Y/G, B-Y/B and R-Y/R connectors on the rear panel.
1-6. Setting of Switches on Boards . S201 -1, 2 (CB CONT) Selects the color bar to be output from the ANALOG COMPOSITE (VBS) generator. Setting switches S201-1 S201-2 Color bar OFF SD COMPONENT-CB ON SD COMPOSITE-CB OFF SMPTE-CB ON EIAJ/EBU Factory setting : S201-1 → ON S201-2 → OFF -3, 4 Not used. Factory setting : OFF . S401 (G/Y SYNC SEL) Selects whether SYNC is added or not to the G/Y signal of SD. ON : Added OFF : Not added Factory setting : ON .
1-6. Setting of Switches on Boards 1-6-8. FC-88 Board (HKCU-953) A B C D E F G H J K 1 FC S6 POWER 2 S1 CONVERT 3 FRAME S5 REF IN UN LOCK 4 S3 S2 5 FC-88 board (A side/panel side) n Do not change the settings of the switches described “Factory use only” and unused switches. . S1 (MODE SET) Factory setting : All OFF -1 (50i → 60i : ENABLE) : Selects whether 50i → 60i conversion is valid or not. ON : 50i → 60i is valid.
1-7. Functions of Indicators on Boards 1-7. Functions of Indicators on Boards 1-7-2. AU-281 Board 1-7-1. AT-149 Board A B C D E 1 D4 D3 AT D101 POWER /1.
1-7. Functions of Indicators on Boards 1-7-3. AVP-4 Board A B C D E 1 DRX D2 POWER 2 60 D201 50 D202 48 D203 PsF D204 D205 540P 3 4 CHARACTER REW 5 D201, D202, D203 (green) : MAIN OUTPUT display Displays the frame frequency of the MAIN HD SDI output signal of this unit and camera. Blinks when the format setting is incorrect. D201 lights up : Lights up when the frame frequency is 30 Hz (or 29.97 Hz) D202 lights up : Lights up when the frame frequency is 25 Hz.
1-7. Functions of Indicators on Boards 1-7-5. DTX-1 Board A B C D E F G H J K 1 DTX D3 POWER OPTICAL CONDITION CCU 2 D605 D606 D607 CHU 3 D608 D609 D610 CHU LOCK 4 D611 RETURN SET HD REM 5 SD DTX-1 board (A side/panel side) n When D607 and D610 light up, be sure to clean the CAMERA connector of the unit, CCU connector of the camera side and the optical/electrical composite cable. When D606 and D609 light up, perform the cleaning as well.
1-7. Functions of Indicators on Boards 1-7-6. RC-91 Board A B 1-7-7. EN-145 Board (HKCU-951) C D E A 1 B C D E 1 EN RC POWER D4 525 D3 VBS 2 2 D5 625 D103 POWER LEVEL SYNC REM LOCAL CHROMA 3 COMPONENT SQ LB 3 R/R-Y EC CENT G/Y 4 4 B/B-Y VAR SC PHASE RIGHT ADV 5 LEFT 5 DELAY RC-91 board (A side/panel side) D4 (green) : POWER display Lights up when the voltage used on this board is normally supplied.
1-7. Functions of Indicators on Boards 1-8. Installing the HKCU-951/953 1-8. Installing the HKCU-951/953 1-7-8. FC-88 Board (HKCU-953) A B C D E 1 1-8-1. Installing the HKCU-951 Installation FC D103 POWER Front side (EN-145 board) 1. Turn off the power and disconnect the power cord from the wall outlet. 2. Loosen the two screws (with drop-safe) and open the front panel in the direction of the arrow.
1-8. Installing the HKCU-951/953 Rear side (VDA-61 board) 1. Remove the two screws and remove the blank panel by holding the handle. n Store the removed blank panel in a safe place. 2. Insert the VDA-61 board in the slot. m . Because there is a difference of the depth between the upper groove and the lower groove, insert the VDA-61 board in a straight line after inserting it in the lower groove. . Check that the VDA-61 board is securely connected to the motherboard (MB-951 board). 3.
1-8. Installing the HKCU-951/953 1-8-2. Installing the HKCU-953 Installation Front side (FC-88 board) 1. Turn off the power and disconnect the power cord from the wall outlet. 2. Open the front panel. (Refer to Section 1-8-1, step 2.) 3. Pull up the lever in the direction of arrow A to unlock and pull out the RC-91 board. 4. Insert the RC-91 board removed in step 3 in the right most slot. Insert the FC-88 board in the second slot from the right most slot.
1-8. Installing the HKCU-951/953 Rear side (SDI-73 board) 1. Remove the two screws and remove the blank panel by holding the handle. 2. Remove the two screws and remove the DIF-124 board. n Store the removed blank panel in a safe place. 3. Insert the DIF-124 board removed in step 2 in the left most slot. Insert the SDI-73 board in the second slot from the left most. m .
1-9. Installing the RM-B750 1-9. Installing the RM-B750 1-9-1. Connecting/Disconnecting the Flexible Card Wire The flexible card wires are used to connect between the following boards. Life of flexile card wire will be significantly shortened if it is folded. Be very careful not to fold the flexible card wire. . One flexible card wire between the AU-281 board (CN2) of the unit and the VA-211 board (CA2) of the RMB750 (when the RM-B750 is installed) .
1-9. Installing the RM-B750 1-9-2. Installing the RM-B750 Removing the Front Panel from the RM-B750 3. Disconnect the connector (CN104) from the MPU-124 board and the connector (CN2) from the VA-211 board respectively. n Life of flexile card wire will be significantly shortened if it is folded. Be very careful not to fold the flexible card wire. 1. Loosen the screw (with drop-safe) of the RM-B750 and open the cover in the direction of the arrow. 4.
1-9. Installing the RM-B750 Installing the Front Panel to the Unit 5. Turn off the power and disconnect the plug from the outlet. 6. Open the front panel of the unit. (Refer to Section 1-8-1. step 2) 7. Remove the screw. 8. Slide the front panel in the direction of the arrow to extract the pin from the potbellied hole and remove the front panel. Pin 11. Connect the flexible card wire to the connector (CN2) of the AU-281 board. m . Do not insert the flexible card wire sideways.
1-10. Installing in 19-inch Rack 1-10. Installing in 19-inch Rack Installation The two HDCU-950 can be mounted in parallel in a 19inch EIA standard rack by using the rack mount adapter RMM-301 (optional). (Height three unit) 1. Secure the RMM-301 in the 19-inch EIA standard rack with the four B5 screws (6 mm or longer). w If the rack falls due to the weight of the equipment, it may cause death or major injury. To prevent the rack from falling or moving, be sure to fix the rack to the floor. 57.
Section 2 System Setup 2-1. System Connection This unit can support input and output of multiple formats. It can also support various types of user’s format by installing the optional circuit boards. The slots to which the circuit boards are inserted and the internal switches setting differ depending upon the system used. They need to be set according to the system used. For the installation procedure, refer to “1-8. Installing the HKCU-951/953”.
2-1. System Connection 2-1-1.
2-1. System Connection 2-1-2. Standard HD/SD System Example of connection HD REFERENCE SIGNAL PROMPTER SIGNAL HD-SDI RETURN VIDEO SIGNAL REFERENCE SIGNAL HD-SDI SIGNAL SYNC OUT (HD) PROMPTER IN SERIAL RET INPUT 1 to 3 REFERENCE IN HDC-950 + CA-905L SERIAL OUTPUT 1, 2 CAMERA +B M3 +B M3 REFERENCE +B M3 PROMPTER +B M3 MIC1 +B M3 RC +B M3 +B M3 2.6 SD SDI OUT 1 +B M3 +B M3 +B M3 +B M3 RET1 +B M3 2.6 SERIAL OUT 1 2.6 SD SDI OUT 2 2.6 SD ANALOG Monitor +B M3 MIC2 +B M3 RET2 2.
2-1. System Connection 2-1-3. HD/SD Film Like System Example of connection SYNC SIGNAL PROMPTER SIGNAL SDI RETURN VIDEO SIGNAL REFERENCE SIGNAL HD-SDI SIGNAL HD-SDI SIGNAL SUB REFERENCE SIGNAL SYNC OUT PROMPTER IN SERIAL RET INPUT 1 to 3 REFERENCE IN SERIAL OUTPUT 1, 2 HDC-950 + CA-905L HD SDI OUT 1, 2 FRAME REF IN SD-SDI SIGNAL CAMERA +B M3 +B M3 REFERENCE +B M3 PROMPTER +B M3 MIC1 SD SDI OUT 1 FC 2.6 2.6 RC +B M3 +B M3 +B M3 HD SDI OUT 1 +B M3 +B M3 +B M3 RET1 +B M3 2.
2-1. System Connection 2-1-4. Analog NTSC/PAL System Example of connection SD SYNC REFERENCE SIGNAL PROMPTER SIGNAL ANALOG RETURN VIDEO SIGNAL REFERENCE SIGNAL ANALOG COMPONENT VIDEO SIGNAL ANALOG COMPOSITE VIDEO SIGNAL SYNC OUT PROMPTER IN RET INPUT 1 to 3 REFERENCE IN RGB/ Component OUT HDC-950 + CA-905L VBS OUT CAMERA +B M3 +B M3 REFERENCE +B M3 PROMPTER +B M3 MIC1 VBS OUT RC 2.6 2.6 EN +B M3 +B M3 +B M3 SD SDI OUT 1 +B M3 +B M3 SERIAL OUT 1 +B M3 RET1 +B M3 2.6 SD SDI OUT 2 2.
2-2. Setting the System Format 2-2. Setting the System Format 2-2-1. Setting the Multi-Format Set format of the signal that is output from this unit. Normally the Multi-Format is set from RM/MSU or a device that is connected outside. However, it can also be set by the switches on the AT-149 board or FC-88 (HKCU-953) board. 1. Setting the HD-SDI output Set format of the signal that is output as the HD-SDI signal. At the same time, this setting becomes the shooting mode of the camera.
2-2. Setting the System Format 2-2-2. Setting the Reference Input Normally the reference input is set from RM/MSU or a device that is connected outside. However, it can also be set by the switch on the AT-149 board. 1. Setting the reference input signal format Setup switch : REFERENCE switch (S427) on the AT-149 panel (Factory setting : REM) HD : When the HD analog ternary SYNC is used. (This unit supports the frame frequency automatically.) BB : When the BB (black burst) signal of SD is used.
2-3. Audio System 2-3. Audio System 2-3-1. Setting the Intercom System J K This unit can be connected to the intercom lines (producer line and engineer line) of the two independent systems and can be switch them. The intercom systems conforming to this unit are 4W, RTS and Clear-Com. The internal switches of the unit need to be set according to the system used.
2-3. Audio System 2. Setting the headset microphone Set switch S4 (TALK GAIN) on the AU-281 board according to the type of headset microphone to be connected to the INCOM connector on the front. When using a carbon microphone : CARBON (Sensitivity _20 dB, power is supplied.) (factory setting) When using a electric condenser microphone : ECM (Sensitivity _40 dB, power is supplied.) When using a dynamic microphone : DYNAMIC (Sensitivity _60 dB, power is not supplied.
2-3. Audio System Setting the microphone input gain of the video camera This unit can output the two independent microphone lines (MIC 1, MIC 2) of video camera HDC-950/930 as it receives these MIC signals. Controlling the Microphone Input Gain Using the Remote Control This unit can adjust the input gain of the MIC connector of camera HDC-950/930 using the remote control in the range of 60 dB to 20 dB in 10 dB steps using either of the following methods.
2-3. Audio System 2-4. Systems 2-4-1. Setting the Tally System This unit supports the red tally and the green tally. It also supports the MAKING CONTACT and supplying power (24 V/TTL). Set the switches on the AVP-4 board according to the system used as follows : S503 RV500 S502 1 J G K H K 2-4. Systems J Setting the Microphone Output Level 1 RV501 S101 S100 The microphone output signal level from the MIC 1, 2 connector on the rear can be adjusted using the volume on the AVP-4 board.
2-4. Systems 2-4-2. Setting the Camera Number 2-4-3. Connecting the Control, Intercom and Tally Audio Signals C D System that does not use CNU-700/500 Use switch S421 on the AT-149 board to set the camera number. Use switches 1 to 4 to set the first digit and use switches 5 to 8 to set the second digit. “0” to “f” can be set as each digit, but “a” to “f” are invalid. Camera numbers 1 to 96 can be set.
2-4. Systems HDCU-950 [1] CAMERA +B M3 +B M3 REFERENCE +B M3 PROMPTER +B M3 MIC1 2.6 RC +B M3 +B M3 +B M3 SD SDI OUT 1 +B M3 +B M3 +B M3 +B M3 RET1 +B M3 2.6 SERIAL OUT 1 2.6 2.6 SD SDI OUT 2 +B M3 MIC2 +B M3 RET2 2.6 WF OUT SERIAL OUT 2 2.6 2.6 PIX OUT 2.6 SYNC OUT +B M3 RET3 RCP/CNU WF MODE 2.6 2.
2-5. Video Signal System 2-5. Video Signal System Adjusting the Phase of the Sync Signal The equipment that is used for this unit and the HDC-950/ 930 series camera system were set to the specified level when shipped from the factory. Before operating, check the signal levels between each equipment and adjust them if required. Some adjustments can be performed using the maintenance menu of the MSU-700A/750 instead of using the control or switches on the board.
2-5. Video Signal System 2-5-3. Setting Aspect Ratio Conversion during Down-convert In the HDC-950/930 series camera system, the aspect ratio can be switched by using the HDCU-950 and MSU-700A/ 750 according to the system during HD-SD down-convert. Set the desired aspect ratio using the MIC REMOTE connector at the rear of the unit or the switch on the AT149 and RC-91 boards. The aspect ratio also can be set on the maintenance menu or the configuration menu of the MSU-700A/750.
2-5. Video Signal System Examples of display 16 : 9 picture (picture from camera) Horizontal cutting position of 16 : 9 Letter box (16 : 9) S7/RC-91 → LB S10-3, -4/RC-91 → OFF The 16 : 9 ratio picture is inserted into the 4 : 3 ratio picture without changing the ratio and is output in the SD SDI format.
2-5. Video Signal System 2-5-4. Level Adjustment of the VBS Signal (only when HKCU-951 is installed) Adjust the level of the VBS signal output from the unit using the color bar signal. Use the switch on the EN-145 board (HKCU-951) and the control on the panel of the unit for adjustment. J K How to adjust using the EN-145 board (HKCU951) of the unit 3. Set the VBS LEVEL and the VBS SYNC control on the EN-145 board panel to their mechanical center.
2-5. Video Signal System 2-5-5. Adjusting the Level of Signals for Waveform Monitor The video output signal of the unit can be checked on the waveform monitor connected to the WF OUT connector. Adjust the WF output signal level using the color bar signal. In the system with the MSU-700A/750, CNU-700/500 or VCS-700, the video output signal can be checked on the waveform monitor connected to the VCS-700. 1. Press the BARS button of the MSU-700A/750, RCP740/741, etc.
2-5. Video Signal System How to adjust using the MSU-700A/750 The signal level can be adjusted by using the MSU-700A/ 750 instead of using the controls of the VCS-700. 1. Press the MAINTENANCE button of the MODE block of the MSU-700A/750 so that the button lights. The maintenance menu is displayed. Each luminescent spot on the vector monitor must be within the “4” range.
2-5. Video Signal System Press the SEQ button of the WAVEFORM MONITOR button (or the MONITOR SELECT button) of the MSU700A/750, RCP-740/741, etc., to output the waveform monitor control signal of the unit, synchronizing with the output signal of the WF OUT connector. A B n The control method of the sequential mode depends on the waveform monitor used. If required, change the polarity of the control from the setting of switch S301 (SEQ) on the RC-91 board.
2-5. Video Signal System 2-5-6. Adjusting the Level of Signals for Picture Monitor The video output signal can be checked on the waveform or vector monitor connected to the PIX OUT connector. Use the color bars to adjust the level of the PIX output signal. In addition, in the system with the MSU-700A/750, CNU700/500 or VCS-700, the video signal of the unit can be checked on the waveform or vector monitor connected to the VCS-700.
2-5. Video Signal System 2-5-7. Setting the RET Input Setting the Aspect Ratio for Up-conversion Set format of the return signal that is input to RET 1 to RET 3 connectors on the rear panel of this unit. Set the desired aspect ratio using the switch on the DTX-1 boards. The aspect ratio also can be set on the maintenance menu or the configuration menu of the MSU-700A/750. For more details, refer to the System Manual.
2-5. Video Signal System How to set the aspect ratio 1. Set RETURN SET switch on the DTX-1 board panel to SD. 2. Set the switch S601 (SD RETURN FORMAT) on the DTX-1 board, to SDI. 3. Set S603 (SD RET ASPECT) and S604 (LB ASPECT) on the DTX-1 board according to the desired aspect ratio. For more details, refer to Section 1-6-5, “Setting of Switches on Boards_DTX-1 Board”.
2-5.
2-5. Video Signal System Setting the Frame Frequency Conversion When the HKCU-953 is installed and the operation frame frequency of the camera is set to 24F (24PsF), set the frame frequency conversion of the return signal. Setup switch : S606 on the DTX-1 board (Factory setting : All OFF) S606-1, -2 : RET 1 S606-3, -4 : RET 2 S606-5, -6 : RET 3 S606-7, -8 : PROMPTER (RET 4) S603-1, -3, -5, -7 S603-2, -4, -6, -8 Type of the frame conversion ON ON THROUGH : Frame frequency is not converted.
2-6. Note on Using the Large Lens Adapter CA-905L 2-6. Note on Using the Large Lens Adapter CA-905L When attaching the large lens adapter CA-905L to the camera to be connected to the HDCU-950, note the following. Viewfinder Use of the 6-type color LCD viewfinder HDVF-C700W is recommended. Because the 7-type B/W viewfinder HDVF-700A consumes a large amount of power, the maximum camera cable length in this case is limited to 300 meters.
Section 3 Service Overview 3-1. Cleaning of Connector/Cable Cleaning Before connecting the unit to the camera, it is recommended to clean the following optical contact portions. . CAMERA connector of the unit . CCU connector of the camera side . Optical/electrical cable Male connector Clean the tip of the white optical contacts by a cotton swab moistened with alcohol. Optical contacts (white) Follow the procedures below for cleaning. Tools Required .
3-1. Cleaning of Connector/Cable 3-2. Recommended Replacement Parts 2. When the turn stops, pull out the remover in the straight line forcedly. n The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover. Great care should be taken so as not to lose or damage the alignment sleeve. (Alignment sleeve: Sony P/N 9-980-074-01) Alignment sleeve 3-2. Recommended Replacement Parts 3-2-1.
3-3. Character Display Function 3-3. Character Display Function The contents of the pages displayed on the HD monitor (or SD analog monitor) are as follows. This unit has the built-in character generation circuit. The character information such as the settings, state and selfdiagnosis of the unit can be mixed with the HD SDI video signal and the SD video signal. The mixed signal can be output from the MONI OUT (DRX-1 board output) and the PIX OUT (RC-91 board output) connector respectively.
3-3. Character Display Function Page 1 Page 3 Camera Lens/Filter Status Display System Status Display 1 EX * System Status * HDC-950 1080/59.94I Gen Lock : SD DRX:1080/59.94I FC :1080/59.94I RC : 525/59.94I 3 2 1A F:CLS 4 RET1:HD 2:HD 3:HD 4:SD SDI SDI SDI VBS 59.94I 59.94I 59.94I SQ 1 2 3 4 5 6 7 8 9 No. Contents No. Contents 1 Displays the setting state of the lens extender. 1 2 Displays the setting state of the ND filter and CC filter.
3-3. Character Display Function Page 4 Page 5 Diagnosis Display System Diag (1/3) Display * System Diag 1/3 * Optical Condition CAMERA CCU * Diagnosis * 1 2 3 AT :OK AVP:OK DTX:OK DRX:OK FC :OK RC :OK 4 5 6 Fan Power Timer OK OK 1 OK 264H 2 3 No. Contents No. Contents 1 Displays the self-diagnosis result of the AT-149 board (OK/NG).*2 1 2 Displays the self-diagnosis result of the AVP-4 board (OK/NG).*2 3 Displays the self-diagnosis result of the DTX-1 board (OK/NG).
3-3. Character Display Function Page 6 Page 7 System Diag (2/3) Display System Diag (3/3) Display * System Diag 2/3 * * System Diag 3/3 * Cable Connect Data OK Power ON 1 2 3 RCP/CNU Cable Connect Data OK Power OFF 4 5 6 PANEL 7 8 9 CAMERA Cable Open Data -Power ON Intercom CAMERA CH1 PROD MIC ON CH2 PROD MIC ON CAMERA MIC Gain CH1 60dB Local CH2 60dB Local 1 2 3 No. Contents No.
3-3. Character Display Function Page 8 Page 9 AT Diag Display AVP Diag Display Displays the details of self-diagnosis of the AT-149 board of the unit. Displays the details of self-diagnosis of the AVP-4 board of the unit. * AT Diag * * AVP Diag * System Frequency 1.001 CHU Format Setting Remote 1080/59.94I 1 Ref.H Phase SD Local HD-SD DLY 90H Marker Setting Remote 3 4 5 CCU Mode 6 No. Normal 2 PLD V1.00 Confing Done AVP Mode Normal Contents 1 Display of system frequency coefficient (1.
3-3. Character Display Function Page 10 Page 11 DTX Diag Dispaly DRX Diag Dispaly Displays the details of self-diagnosis of the DTX-1 board of the unit. Displays the details of self-diagnosis of the DRX-1 board of the unit. * DTX Diag * * DRX Diag * Return Setting:Remote Return Delay :1Field RET4(VBS) :ON 1 2 3 Return FC mode:Auto 4 PLD V1.00 Config Done DTX Mode Normal 5 6 CB Select Bar-16:9(100%) 1 PLD V1.00 Config Done DRX Mode Normal 2 3 No. Contents No.
3-3. Character Display Function Page 12-1 Page 12-2 Slot-5 Diag Dispaly Slot-5 Diag Dispaly Displays the details of self-diagnosis of the RC-91 board when it is mounted in the fifth slot from the left on the front side of the unit. Displays the details of self-diagnosis of the FC-88 board when it is mounted in the fifth slot from the left on the front side of the unit. * Slot-5 Diag * * Slot-5 Diag * Front: RC Squeeze 1 PLD V1.
3-3. Character Display Function Page 13-1 Page 13-2 Slot-6 Diag Dispaly Slot-6 Diag Dispaly Displays the details of self-diagnosis of the EN-145 board when the EN-145 board is mounted in the sixth slot (right most) from the left of the front side of the unit. Displays the details of self-diagnosis of the RC-91 board when the RC-91 board is mounted in the sixth slot (right most) from the left of the front side of the unit. * Slot-6 Diag * * Slot-6 Diag * Front: EN Front: RC Squeeze 1 PLD V1.
3-3. Character Display Function Page 14 ROM Version Dispaly Displays the ROM versions of the unit and the peripheral equipment of the unit. * ROM Version * CHU CCU MSU HDC-950 1.20DM01 HDCU-950 1.02 MSU-700A/750 1.10 1 2 3 No. Contents 1 Displays the ROM version of the camera. 2 Displays the ROM (IC510 and IC553 on the AT-149 board) version of the HDCU-950. 3 Displays the ROM version of the equipment that is connected to the RCP/CNU connector on the rear panel of he HDCU-950.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer : The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
HDCU-950 (SY) J, E 3-619-324-04 Sony Corporation B&P Company Printed in Japan 2003.