3-043-723-11 (1) Cordless Telephone Operating Instructions US Manual de instrucciones ES SPP-933 ©1999 Sony Corporation
Owner’s Record The model and the serial numbers are located at the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. SPP-933 Serial No. ________________ IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1.
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions.
6. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. 7. If trouble is experienced with this equipment (SPP-933), for repair or warranty information, please contact Sony Direct Response Center: Tel 1-800-222-7669.
Table of contents Getting Started 6 7 Read this first Step 1: Checking the package contents 8 Step 2: Setting up the base phone 11 Step 3: Preparing the battery pack 13 Identifying the parts Basics 16 Making calls 18 Redialing 19 Receiving calls Telephone Features 20 Speed dialing 20 Storing phone numbers on the handset 21 Storing phone numbers on the base phone 22 Making calls with speed dialing on the handset 22 Making calls with speed dialing on the base phone 23 Setting the ringer type 23 Turning off
Getting Started Read this first Before you use your phone, you must first set it up. Here’s a quick way to set up your phone: Steps 1, 2 and 3. Step 1 (page 7) First, unpack the phone and the supplied accessories. Step 2 (pages 8 to 10) Next, you need to do three things to set up the base phone, including finding the best location for the base phone. Base phone Step 3 (pages 11 to 12) Then, insert the battery pack into the handset and charge it for more than 12 hours.
Step 1 Checking the package contents Make sure you have received the following items in the package. If anything is missing, contact your local Sony dealer.
Step 2 Setting up the base phone Do the following steps: • Choose the best location • Connect the base phone • Choose the dialing mode Choose the best location Where you place the base phone affects the reception quality of the handset.
Connect the base phone If you want to hang the base phone on the wall, see page 32. 3 Route the code Getting Started To an AC outlet To DC IN 9V 2 AC power adaptor (supplied AC-T129) To LINE Align the f marks. 2 1 Telephone line cord To the telephone outlet (supplied) 1 If you want to use the wall bracket as the stand, attach it on the bottom of the base phone before step 1 as illustrated above. 1 Connect the telephone line cord to the LINE jack and to a telephone outlet.
Step 2: Setting up the base phone (continued) Notes • Use only the supplied AC-T129 AC power adaptor. Do not use any other AC power adaptor. • Connect the AC power adaptor to a continuous power supply. • Place the base phone close to the AC outlet so that you can unplug the AC power adaptor easily. Tip If your telephone outlet is not modular, contact your telephone service company for assistance.
Step 3 Preparing the battery pack Charge the battery pack for more than 12 hours before you start using your phone. compartment lid of the handset. 2 Connect the battery connector BP-T18 with correct polarity (black wire goes on left side and red wire goes on right). Getting Started 1 Slide open the battery Red Black 3 Close the battery compartment lid. 4 Place the handset on the base phone. The CHARGE lamp lights up when the handset is properly seated on the charge terminals of the base phone.
Step 3: Preparing the battery pack (continued) Battery duration A fully charged battery pack lasts for about: • approx. 7 hours when you use the handset continuously. • approx. 7 days when the handset is in standby mode. Notes • The battery pack will gradually discharge over a long period of time, even if not in use. • If you leave the battery pack in the handset without charging it, the battery pack will be completely discharged. It may require several times of charging to recover its full capacity.
Identifying the parts Refer to the pages indicated in parentheses for details. Handset 1 4 5 Getting Started 2 3 0 qa qs qd qf 6 7 8 9 qg qh qj 1 Antenna 2 Speaker 3 TALK/BATT LOW lamp (p. 16, 20) Lights up during a call, flashes when you store a phone number for speed dialing. 4 VOL (volume) switch (p. 16, 19) Adjusts the handset volume. 5 TALK button (p. 16, 19) Lets you make or receive a call. 6 Dialing keys (p. 16) 7 Battery compartment (p. 11) 8 TONE button (p.
Identifying the parts (continued) Base Phone q; qa qs 1 2 3 4 5 qd qf 6 7 qg 8 qh qj 9 1 PGM (Program) button (p. 21) Used to store numbers for speed dialing. 2 Dialing keys (p. 17) 3 TONE button (p. 17, 19) Allows you to switch temporarily to tone dialing. 4 LINE lamp (p. 17, 19, 25) Lights when one of the phones is in use. 5 CHARGE lamp (p. 11) Lights while the battery is being charged. 6 HOLD button (p. 17, 19, 25) Used to hold a call. 7 MIC (microphone) 8 SPEAKERPHONE lamp (p.
Getting Started qk ql w; wa qg VOLUME control (p. 17, 19) Adjusts the speaker volume. qh INTERCOM button (p. 28) Used to make an intercom call. qj INTERCOM lamp (p. 27) Lights up during an intercom call. qk RINGER switch (p. 24) Adjusts the ringer volume. ql DIAL MODE switch (p. 10) Selects pulse or tone dialing. w; DC IN 9V jack (p. 9, 32) wa LINE (telephone line) jack (p.
Basics Making calls 1 Pick up the handset from the base phone. 2 Press (TALK). TALK/BATT LOW lamp The TALK/BATT LOW lamp on the handset and the LINE lamp on the base phone light up. (FLASH) VOL switch (CHANNEL) (HOLD) Then you’ll hear a dial tone. If you hear error beeps, move closer to the base phone. 3 Dial the phone number. 4 When you’re done talking, press (*TONE) (REDIAL/PAUSE) (OFF) or replace the handset on the base phone.
If the handset battery becomes weak during a call You hear a beep every three seconds and the TALK/BATT LOW lamp on the handset flashes. The call will disconnect soon. Replace the handset on the base phone to charge. For optimum performance, charge the battery for a full 12 hours. Note that during the first 10 - 15 minutes of charging, the phone will be inactive, i.e., unable to make or receive a call.
Making calls (continued) To obtain the best speakerphone performance • You may not be able to hear the other party’s voice in a noisy place. Therefore, use the speakerphone in a quiet room. • Do not bring your hand or other object too close to the microphone or you will hear a shrill noise (“feedback”). • When the speaker volume is loud, or the telephone has been placed close to a wall, you may find that the volume drops suddenly.
Receiving calls 1 When you hear the phone ring; TALK/BATT LOW lamp VOL switch (FLASH) (HOLD) • Press (TALK) (or any key except (OFF)) . or • Pick up the handset from the base phone when the handset is placed on the base phone. The TALK/BATT LOW lamp on the handset and the LINE lamp on the base phone light up. 2 When you’re done talking, press (*TONE) (CHANNEL) To Do this Put a call on hold Press (HOLD). The TALK/BATT LOW lamp flashes slowly. Press (TALK) to resume the conversation.
Telephone Features Speed dialing You can dial with a touch of a few buttons by storing a phone number on a dialing key. You can store up to 10 different phone numbers separately on the handset and on the base phone. Storing phone numbers on the handset 1 Press (PGM). The TALK/BATT LOW lamp flashes. 2 Press one of the dialing keys TALK/BATT LOW lamp ((0) to (9)) for the phone number to be stored. You’ll hear a confirmation beep. 3 Enter the phone number you (TALK) want to store.
Storing phone numbers on the base phone 1 Press (PGM). The SPEAKERPHONE lamp flashes quickly. 2 Press one of the dialing keys ((0) to (9)) for the phone number to be stored. LINE lamp You’ll hear a confirmation beep. 3 Enter the phone number you want to store. (SPEED DIAL) (REDIAL/PAUSE) SPEAKERPHONE lamp (SPEAKERPHONE) You can enter up to 16 digits, including a tone and a pause, each of which is counted as one digit. 4 Press (PGM) again.
Speed dialing (continued) To store the previous number dialed Press (REDIAL/PAUSE) directly after step 2, then go to step 4. To store a number to be dialed via Private Branch Exchange (PBX) Before entering a phone number in step 3 on the previous page, do as follows: 1 2 Enter the outside line access digit (e.g. 9). Press (REDIAL/PAUSE). To change a stored number To store a new number, follow the instructions described previously. To clear a number from memory 1 Press (PGM).
Setting the ringer type You can select a ringer type from four types. 1 Press (PGM). 2 Press (#) or (*TONE). 3 Press a number button, (1) to (4), to select a ringer type. (OFF) You’ll hear the corresponding ringer tone. 4 Press (OFF). (*TONE) (#) 1 2 3 4 Telephone Features Turning off the ringer Press (PGM). Press (#) or (*TONE). Press (5). Press (OFF). The ringer on the handset is turned off. To turn the ringer on again Follow the instructions described in “Setting the ringer type.
Setting the ringer type (continued) Checking the ringer type 1 2 3 Press (PGM). Press (#) or (*TONE). Press (0). The currently selected ringer sounds. 4 Press (OFF). Note If you hear no sound (only key beep), the ringer on the handset has been turned off. Adjusting the ringer volume level of the base phone Set the RINGER switch on the base phone to HIGH or LOW. To turn the ringer off, set it to OFF.
Switching the phones during a call When you put a call on hold, you can return to the call on the other phone without disconnecting the call. To switch from the base phone to the handset 1 Press (HOLD) on the base phone. LINE lamp The LINE lamp and the TALK/ BATT LOW lamp on the handset will flash slowly. 2 Press (TALK) or pick up the handset from the base phone. The LINE lamp and the TALK/ BATT LOW lamp on the handset will light up.
Switching the phones during a call (continued) To switch from the handset to the base phone 1 Press (HOLD) on the handset. TALK/BATT LOW lamp The TALK/BATT LOW lamp and the LINE lamp on the base phone will flash slowly. 2 Press (SPEAKERPHONE). The SPEAKERPHONE lamp on the base phone will light up. The TALK/BATT LOW lamp will flash. 3 When you are done talking, press (SPEAKERPHONE) again.
Talking between the handset and the base phone (Intercom) You can talk between the base phone and the handset. You can start the intercom from either phone. To talk from the handset to the base phone Press (INTERCOM) on the handset. TALK/BATT LOW lamp (TALK) (OFF) The TALK/BATT LOW lamp lights up, and INTERCOM lamp flashes. The base phone rings. You will be connected automatically after 3 seconds. When a person at the base phone answers, you can talk.
Talking between the handset and the base phone (Intercom) (continued) To talk from the base phone to the handset (SPEAKERPHONE) INTERCOM lamp Press (INTERCOM) on the base phone. The handset rings. TALK/BATT LOW lamp flashes. When the person at the handset presses (INTERCOM), you can talk. The call to the handset will stop by pressing (OFF) on the handset. The TALK/BATT LOW lamp on the handset will light up. The INTERCOM lamp on the base phone will light up.
Transferring a call You can transfer a call between the handset and base phone without disconnecting the call. To transfer from the base phone to the handset 1 Press (INTERCOM). The call is put on hold, the handset rings. The TALK/BATT LOW lamp on the handset flashes. 2 Press (INTERCOM) on the handset. (SPEAKERPHONE) INTERCOM lamp talk to the caller with the handset. (INTERCOM) If no one answers the phone Press (SPEAKERPHONE) on the base phone.
Transferring a call (continued) To transfer from the handset to the base phone 1 Press (INTERCOM). TALK/BATT LOW lamp The call is put on hold, the base phone rings. The INTERCOM lamp on the base phone flashes. You will be connected automatically after 3 seconds. (TALK) The TALK/BATT LOW lamp on the handset lights up. When a person at the base phone answers, you can talk. 2 Press (SPEAKERPHONE) on the base phone to talk to the caller with the base phone.
Having a three-way conference The handset and the base phone operate like two extensions on the same line. Both phones can operate at the same time, so that you, the outside caller, and the person at the other phone can engage in a threeway conversation. To join the phone conversation TALK/BATT LOW lamp Press (TALK). The TALK/BATT LOW lamp on the handset lights up. If you are at the base phone, simply press (SPEAKERPHONE). (TALK) The SPEAKERPHONE lamp on the base phone lights up.
Additional Information Mounting the base phone on a wall 1 1 Raise the hang-up tab. 2 Plug the telephone line cord to Hang-up tab the LINE jack and the AC power adaptor to the DC IN 9V jack, and hook the cords. Use the shorter cord for mounting. 3 Attach the wall bracket to the center of the base phone. Align the fmarks of the wall bracket with those of the base phone.
Notes on power sources On battery pack For the customers in the USA • Store the battery pack at a temperature between 41°F (5°C) and 95°F (35°C) for best performance. RECYCLING NICKEL-CADMIUM BATTERIES • If you do not use the handset for a long period of time, remove the battery pack after charging for more than 12 hours. This maintains battery life. On power failure During a power interruption, you cannot make or receive calls. Nickel-Cadmium batteries are recyclable.
Maintenance • Clean the cabinets with a soft cloth slightly moistened with water or a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine as they may damage the finish of the cabinet. • If the charge terminals of the base phone and handset are soiled, wipe them with a soft cloth. If you have any questions or problems concerning your phone, please consult your nearest Sony dealer.
Troubleshooting Remedy You hear five short error beeps when you press (TALK). • Make sure you have set up the base phone correctly (page 8). • Move the handset closer to the base phone. • Replace the handset to the base phone for a while to reset the random security code. You hear no dial tone. • Make sure the telephone line cord is securely connected to the telephone outlet. • Make sure the battery is fully charged (page 11).
Power source/battery Intercom Speed dialing Troubleshooting (continued) 36US Symptom Remedy You cannot store a speed dialing number. • Make sure you follow the procedure in storing the number correctly (page 20). • When the handset is in use, you cannot store a speed dialing number on the base phone. • Replace the handset to the base phone for a while. You cannot make a speed dialing call. • You pressed the number button to which no phone number has been stored. Speed dialing is incorrect.
Specifications General Base phone Frequency band 902 - 928 MHz Operating channel 40 channels Dial signal Tone, 10 PPS (pulse) selectable Supplied accessories See page 7. Power source DC 9V from AC power adaptor AC-T129 Dimensions Approx. 170 x 65 x 220 mm (w/h/d), antenna excluded (approx. 6 3⁄4 x 2 5⁄8 x 8 3⁄4 inches) Antenna: Approx. 150 mm (approx. 6 inches) Mass Approx. 560 g (approx.
Index A M, N, O T, U Adjusting volume handset volume 16, 19 speaker volume 17, 19 Making calls 16 Mounting the base phone on a wall 32 B P, Q Battery pack charging 11 duration 12 Package contents 7 Pulse dialing 10 Talking between the phones 27 Three-way conference 31 Tone dialing dialing mode 10 switching to 16, 19 Transferring a call 29 Troubleshooting 35 C Receiving calls 19 Redialing 18 Ringer adjusting the base ringer 24 setting the ringer type 23 turning on/off 23 Connection 9 D, E, F, G,
Registro del propietario Los números de modelo y de serie se encuentran en la parte inferior del teléfono. Anote el número de serie en el espacio que se proporciona a continuación. Refiérase a estos números cada vez que se comunique con su distribuidor Sony con respecto al producto.
12. Desconecte este producto de la línea telefónica y refiera el servicio a personal de servicio calificado bajo las siguientes condiciones: A. Cuando el cable eléctrico o el enchufe se encuentra dañado o deshilachado. B. Si se ha derramado líquido dentro del producto. C. Si el producto ha estado expuesto a lluvia o agua. D. Si el producto no opera normalmente al seguir las instrucciones de operación.
6. La compañía telefónica puede realizar cambios en sus instalaciones, equipos, operaciones, o procedimientos que pueden afectar la operación del equipo. Cuando suceda esto, la compañía telefónica le avisará con antelación para que usted realice las modificaciones necesarias para mantener ininterrumpido el servicio. 8. Todas las reparaciones deberá realizarlas un centro de reparaciones Sony.
Índice Preparativos 6 Lea esto en primer lugar 7 Paso 1: Comprobación del contenido del paquete 8 Paso 2: Instalación del teléfono base 11 Paso 3: Preparación de la batería 13 Identificación de las partes Operaciones básicas 16 Realización de llamadas 18 Repetición de la marcación 19 Recepción de llamadas Funciones del teléfono 20 Marcación rápida 20 Almacenamiento de números de teléfono en el microteléfono 21 Almacenamiento de números de teléfono en el teléfono base 22 Realización de llamadas con marcaci
Preparativos Lea esto en primer lugar Antes de utilizar su teléfono, tendrá que instalarlo. A continuación se indica la forma rápida de hacerlo: Pasos 1, 2, y 3. Paso 1 (página 7) En primer lugar, desembale el teléfono y los accesorios suministrados. Paso 2 (páginas 8 a 10) A continuación, tendrá que hacer tres cosas para instalar el teléfono base, incluyendo la búsqueda del mejor lugar para el mismo.
Paso 1 Comprobación del contenido del paquete Compruebe si con el paquete ha recibido los elementos siguientes. Si falta algo, póngase en contacto con su proveedor Sony.
Paso 2 Instalación del teléfono base Realice los pasos siguientes: • Elección del mejor lugar • Conexión del teléfono base • Elección del modo de marcación Elección del mejor lugar La situación del teléfono base afectará la calidad de la recepción del microteléfono.
Conexión del teléfono base Si desea colgar el teléfono base de una pared, consulte la página 32. 3 Enrute el cable Preparativos A un tomacorriente de CA A DC IN 9V 2 Adaptador de alimentación de A LINE CA (AC-T129 suministrado) Alinee las marcas f. 2 1 Cable de línea telefónica A la toma telefónica (suministrado) 1 Si desea utilizar el para instalación mural como soporte, fíjelo en la base del teléfono antes del paso 1, como se muestra en a ilustración de arriba.
Paso 2: Instalación de la teléfono base (continuación) Notas • Utilice solamente el adaptador de alimentación de CA AC-T129 suministrado. No utilice ningún otro adaptador de alimentación de CA. • Conecte el adaptador de alimentación de CA a un tomacorriente que suministre continuamente alimentación. • Coloque el teléfono base cerca del tomacorriente de CA a fin de poder desenchufar fácilmente el adaptador de alimentación de CA.
Paso 3 Preparación de la batería Antes de utilizar su teléfono, cargue la batería durante más de 12 horas. compartimiento de la batería del microteléfono. 2 Conecte el conector con la BP-T18 Rojo Preparativos 1 Deslice y abra la tapa del polaridad correcta (cable negro en el lado izquierdo y rojo en el derecho). Negro 3 Cierre la tapa del compartimiento de la batería. 4 Coloque el microteléfono en el Lámpara CHARGE teléfono base.
Paso 3: Preparación de la batería (continuación) Duración de la batería Una batería completamente cargada durará: • aproximadamente 7 horas cuando utilice continuamente el microteléfono. • aproximadamente 7 días con el microteléfono en el modo de espera. Notas • La batería se descargará gradualmente con el tiempo, incluso aunque no se utilice. • Si deja la batería en el microteléfono sin cargarla, se descargará completamente. Para que la batería recupere su plena capacidad, pueden requerirse varias cargas.
Identificación de las partes Con respecto a los detalles, consulte las páginas indicadas entre paréntesis. Microteléfono 1 5 6 7 8 9 0 qa qs qd qf Preparativos 2 3 4 qg qh qj 1 Antena 2 Altavoz 3 Lámpara TALK/BATT LOW (p. 16, 20) Permanencerá encendido mientras esté realizando llamadas, parpadeará cuando se almancenen números de marcación rapida. 4 Selector de volumen (VOL) (p. 16, 19) Presiónelo para ajustar el volumen del microteléfono. 5 Botón de conversación (TALK) (p.
Identificación de las partes (continuación) Teléfono base 1 2 3 4 5 6 7 q; qa qs qd qf qg 8 9 1 Botón de programa (PGM) (p. 21) Utilícelo para almacenar números de marcación rápida. 2 Teclas de marcación (p. 17) 3 Botón de tono ( TONE) (p. 17, 19) Le permitirá cambiar temporalmente a la marcación por tonos. 4 Lámpara indicadora de utilización (LINE) (p. 17, 19, 25) Permanecerá encendida mientras esté utilizando uno de los teléfonos. 5 Lámpara de carga (CHARGE) (p.
Preparativos qk ql w; wa qg Control de volumen (VOLUME) (p. 17, 19) Presiónelos para ajustar el volumen del altavoz. qh Botón de intercomunicación (INTERCOM) (p. 28) Utilícelo para realizar una llamada de intercomunicación. qj Lámpara indicadora de intercomunicación (INTERCOM) (p. 27) Permanecerá encendido durante una llamada de intercomunicación. qk Selector de volumen de la campanilla (RINGER) (p. 24) Ajusta el volumen de la campanilla. ql Selector de modo de marcación (DIAL MODE) (p.
Operaciones básicas Realización de llamadas 1 Tome el microteléfono del teléfono base. 2 Presione (TALK). Lámpara TALK/BATT LOW Selector VOL (FLASH) (CHANNEL) (HOLD) La lámpara TALK/BATT LOW del microteléfono y la lámpara LINE del teléfono base se encenderán. Después oirá el tone de invitación a marcar. Si oye pitidos de error, acérquese al teléfono base. 3 Marque el número de teléfono.
Si la batería del teléfono se debilita durante una llamada Se oye un pitido cada tres segundos y la lámpara TALK/BATT LOW del microteléfono se enciende. La llamada se desconectará pronto. Coloque el microteléfono sobre el teléfono base para cargar. Para obtener el óptimo rendimiento, cargue la batería durante 12 horas. Tenga en cuenta que durante los primeros 10 - 15 minutos de la carga, el teléfono estará inactivo, es decir no podrá realizar ni recibir llamadas.
Realización de llamadas (continuación) Para obtener el máximo rendimiento del modo de interfono • Es posible que en un lugar ruidoso no oiga la voz de su interlocutor. Por lo tanto, utilice la función de interfono en una sala silenciosa. • No acerque demasiado la mano ni ningún otro objeto al micrófono, ya que oiría un aullido (“retroalimentación acústica”). • Cuando el volumen del altavoz sea alto, o si el teléfono está colocado cerca de una pared, puede notar que el volumen desciende repentinamente.
Recepción de llamadas 1 Cuando oiga sonar el teléfono: • Presione (TALK) Lámpara TALK/BATT LOW Selector VOL (FLASH) (HOLD) (o cualquiera tecla excepto (OFF)). o • Tome el microteléfono cuando esté sobre el teléfono base. La lámpara TALK/BATT LOW del microteléfono y la lámpara LINE del teléfono base se encenderán. 2 Cuando se termine de hablar, presione (OFF) o coloque el (*TONE) (CHANNEL) Para Realice lo siguiente Poner una llamada en retención Presione (HOLD).
Funciones del teléfono Marcación rápida Usted podrá marcar presionando unas pocas teclas después de haber almacenado números de teléfono en las teclas de marcatión. Usted podrá almacenar hasta 10 números de teléfono por separado en el microteléfono y en el teléfono base. Almacenamiento de números de teléfono en el microteléfono 1 Presione (PGM). La lámpara TALK/BATT LOW parpadeará. 2 Presione una de las teclas de marcación ((0)a (9)) para almacenar Lámpara TALK/BATT LOW un número de teléfono.
Almacenamiento de números de teléfono en el teléfono base 1 Presione (PGM). La lámpara SPEAKERPHONE parpadeará rápidamente. 2 Presione una de las teclas de marcación ((0) a (9)) para almacenar un número de teléfono. Lámpara LINE Usted oirá un pitido de confirmación. (SPEED DIAL) (REDIAL/PAUSE) Lámpara SPEAKERPHONE (SPEAKERPHONE) 3 Introduzca el número de teléfono que desee almacenar. Usted podrá introducir hasta 16 dígitos, incluyendo un tono o una pausa, que se contarán cada uno como un dígito.
Marcación rápida (continuación) Para almacenar el número previamente marcado Presione (REDIAL/PAUSE) directamente despues del paso 2, a continuación vaya al paso 4. Para almacenar un número para marcarlo mediante la función de tablero conmutador de abonado (PBX) Antes de introducir el número de teléfono en el paso 3 de la página anterior, realice lo siguiente: 1 2 Introduzca el dígito de acceso a la línea exterior (p. ej., 9). Presione (REDIAL/PAUSE).
Ajuste el tipo de campanilla Usted podrá selecionar uno de cuatro tipos de campanilla. 1 Presione (PGM). 2 Presione (#) o (*TONE). 3 Presione una tecla de número, (1) a (4), para seleccionar un tipo de (OFF) campanilla. Usted oirá el tono de campanilla correspondiente. (*TONE) (#) 4 Presione (OFF). Funciones del teléfono Desactivación de la campanilla 1 2 3 4 Presione (PGM). Presione (#) o (*TONE). Presione (5). Presione (OFF). La campanilla del microteléfono se desactivará.
Ajuste el tipo de campanilla (continuación) Comprobación del tipo de campanilla 1 2 3 Presione (PGM). Presione (#) o (*TONE). Presione (0). El tipo de campanilla selecionado sonará. 4 Presione (OFF). Nota Si no oye sonido (sólo un pitido de tecla), la campanilla del microteléfono se habrá desactivado. Ajuste del nivel del volumen de la campanilla del teléfono base Ponga el selector RINGER del teléfono base en HIGH o LOW. Para desactivar la campanilla, póngalo en OFF.
Cambio de teléfonos durante una llamada Si pone una llamada en retención, podrá volver a tomarla en el otro teléfono sin que se desconecte. Para cambiar del teléfono base al microteléfono 1 Presione (HOLD) del teléfono base. Lámpara LINE La lámpara LINE y la lámpara TALK/BATT LOW del microteléfono parpadearán lentamente. 2 Presione (TALK) o descuelgue el microteléfono del teléfono base. La lámpara LINE y la lámpara TALK/BATT LOW del microteléfono se encenderán.
Cambio de teléfonos durante una llamada (continuación) Para cambiar del microteléfono al teléfono base 1 Presione (HOLD) del microteléfono. Lámpara TALK/BATT LOW La lámpara TALK/BATT LOW y la lámpara LINE del teléfono base parpadearán lentamente. 2 Presione (SPEAKERPHONE). La lámpara SPEAKERPHONE del teléfono base se encenderá. La lámpara TALK/BATT LOW parpadeará. 3 Cuando termine de conversar, vuelva a presionar (SPEAKERPHONE).
Conversación entre el microteléfono y el teléfono base (Intercomunicación) Usted podrá conversar entre el teléfono base y el microteléfono. Usted podrá iniciar la intercomunicación desde cualquier teléfono. Lámpara TALK/BATT LOW (TALK) (OFF) Para conversar del microteléfono al teléfono base Presione (INTERCOM) del microteléfono. La lámpara TALK/BATT LOW y la lámpara INTERCOM parpadeará. El teléfono base sonará. Usted se conectará automáticamente después de 3 segundos.
Conversación entre el microteléfono y el teléfono base (Intercomunicación) (continuación) Para conversar del teléfono base al microteléfono Presione (INTERCOM) del teléfono base. El microteléfono sonará. La lámpara TALK/BATT LOW parpadeará. Cuando la persona del microteléfono presione (INTERCOM), usted podrá conversar. La llamada con al microteléfono se parará al presionar (OFF) del mismo. La lámpara TALK/BATT LOW del microteléfono se encenderá. La lámpara INTERCOM del teléfono base se encenderá.
Transferencia de una llamada Usted podrá transferir una llamada entre el microteléfono y el teléfono base sin desconectar dicha llamada. Para transferir del teléfono base al microteléfono 1 Presione (INTERCOM). La llamada se pondrá en retención, y sonarán el microteléfono . La lámpara TALK/BATT LOW del microteléfono parpadeará. 2 Presione (INTERCOM) del microteléfono. (SPEAKERPHONE) Lámpara INTERCOM La lámpara TALK/BATT LOW del microteléfono y la lámpara INTERCOM del teléfono base se encenderán.
Transferencia de una llamada (continuación) Para transferir del microteléfono al teléfono base 1 Presione (INTERCOM). Lámpara TALK/BATT LOW La llamada se pondrá en retención, y sonará el teléfono base. La lámpara INTERCOM del teléfono base parpadeará. Usted se conectará automáticamente después de 3 segundos. (TALK) La lámpara TALK/BATT LOW del microteléfono se encenderá. Cuando la persona del teléfono base conteste, podrá conversar.
Celebración de una conferencia tripartita El microteléfono y el teléfono base funcionan como dos extensiones de la misma línea. Ambos teléfonos podrán utilizarse al mismo tiempo, por lo que usted, la persona que llamó del exterior, y quien se encuentre en el otro teléfono podrán entablar una conversación tripartita. Para unirse a la conversación telefónica Lámpara TALK/BATT LOW Presione (TALK). La lámpara TALK/BATT LOW del microteléfono se encenderá.
Información adicional Montaje del teléfono base en una pared 1 1 Levante la lengüeta de colgado. 2 Enchufe el cable de la línea Lengüeta de colgado telefónica en la toma LINE y el adaptador de alimentación en la toma DC IN 9V, y enganche los cables. Utilice el cable más corto para el montaje. 3 Fije el soporte mural en el centro del teléfono base. Alinee las marcas f del soporte mural con las del teléfono base.
Notas sobre las fuentes de alimentación Batería Para clientes en EE.UU. • Para un óptimo rendimiento, almacene la batería a una temperatura de entre 5°C y 35°C. RECICLAJE DE PILAS DE NÍQUELCADMIO • Cuando no vaya a utilizar el teléfono durante mucho tiempo, extraiga la batería después de haberla cargado durante más de 12 horas. Esto prolongará la duración útil de las baterías.
Mantenimiento • Limpie el exterior con un paño suave ligeramente humedecido en agua o en una solución de detergente neutro. No utilice limpiadores abrasivos, desengrasantes ni disolventes, como el alcohol o la bencina, ya que podrían dañar el acabado. • Si los terminales de carga del teléfono base y el auricular están sucios, límpielos con un paño suave. En caso de duda o problemas con el teléfono, consulte a su proveedor Sony más próximo.
Solución de problemas Síntoma Solución Se oyen cinco pitidos cortos de error al presionar (TALK). • Compruebe si ha instalado correctamente la unidad base (página 8). • Acerque el microteléfono al teléfono base. • Coloque el microteléfono en el teléfono base durante cierto tiempo para que se reponga el código de seguridad aleatorio. No se oye el tono de invitación a marcar. • Compruebe si el cable de línea telefónica está conectado con seguridad a la toma telefónica.
Marcación rápida Solución de problemas (continuación) Síntoma Solución No es posible almacenar un número de marcación rápida. • Asegúrese que ha realizado correctamente el procedimiento de almacenamiento del número (página 20). • Cuando esté utilizando el microteléfono, no podrá almacenar un número de marcación abreviada en el teléfono base. • Coloque el microteléfono sobre el teléfono base durante un momento. No es posible realizar una llamada de marcación rápida.
Especificaciones Generales Teléfono base Banda de frecuencias 902 - 928 MHz Canales de operación 40 canales Señal de marcación Tonos y pulsos (10 pps), seleccionable Accesorios suministrados Consulte la página 7. Fuente de alimentación 9 V CC del adaptador de alimentación de CA AC-T129 Dimensiones Aprox. 170 x 65 x 220 mm (an/al/prf), excluyendo la antena Antena: Aprox. 150 mm Masa Aprox.
Índice alfabético A I, J, K, L R Ajuste del volumen volumen del altavoz 17, 19 volumen del microteléfono 16, 19 Altavoz 17, 19 Identificación de las partes 13 Instalación microteléfono 11 teléfono base 8 Intercomunicación 27 Realización de llamadas 16 Recepción de llamadas 19 Repetición de la marcación 18 B M, N, O, P, Q Solución de problemas 35 Batería carga 11 duración 12 Marcación por pulsos 10 Marcación por tonos cambio a 16, 19 modo de marcación 10 Marcación rápida 20 Modo de marcación cambio
Información adicional Información adicional 39ES
40ES Información adicional
Para clientes en EE. UU.
For the customers in the USA Sony Corporation Printed in the Philippines UCZZ01256EZ