lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB01COV_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 1 Monday, March 28, 2005 4:08 PM 2-514-877-12(1) FM Stereo FM/AM Receiver Operating Instructions Owner’s Record The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Serial No. Model No.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB02REG_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 2 Monday, March 28, 2005 4:08 PM WARNING WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent fire, do not cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. And don’t place lighted candles on the apparatus.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB02REG_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 3 Monday, March 28, 2005 4:08 PM About This Manual • The instructions in this manual are for model STR-DA3100ES. Check your model number by looking at the lower right corner of the front panel. • The instructions in this manual describe the controls on the receiver.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB01COV_STR-DA3100ES-UTOC.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 4 Monday, March 28, 2005 4:08 PM Table of Contents Getting Started 1: Check how to hookup your components .......................................... 5 1a: Connecting components with digital audio output jacks .............. 7 1b: Connecting components with multi channel output jacks ..........
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 5 Monday, March 28, 2005 4:08 PM Getting Started Steps 1a through 1c beginning on page 7 describe how to hook up your components to this receiver. Before you begin, refer to “Connectable components” below for the pages which describe how to connect each component.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 6 Monday, March 28, 2005 4:08 PM Required cords The hookup diagrams on the subsequent pages assume the use of the following optional connection cords (A to H) (not supplied).
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 7 Monday, March 28, 2005 4:08 PM . 1a: Connecting components with digital audio output jacks Getting Started Hooking up a DVD player, TV monitor, or satellite tuner For details on the required cords (A–H), see page 6. 1 Connect the audio jacks.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 8 Monday, March 28, 2005 4:08 PM 2 Connect the video jacks. The following illustration shows how to connect a TV or satellite tuner and a DVD player with COMPONENT VIDEO (Y, PB/CB/B-Y, PR/CR/R-Y) output jacks. Connecting a TV with component video input jacks allows you to enjoy higher quality video.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 9 Monday, March 28, 2005 4:08 PM Hooking up a Super Audio CD/CD player or MD/DAT deck Getting Started For details on the required cords (A–H), see page 6.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 10 Monday, March 28, 2005 4:08 PM 1b: Connecting components with multi channel output jacks 1 Connect the audio jacks. If your DVD or Super Audio CD player is equipped with multi channel output jacks, you can connect it to this receiver’s MULTI CH IN jacks to enjoy the multi channel sound.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 11 Monday, March 28, 2005 4:08 PM 2 Connect the video jacks. Notes • On this receiver, standard video signals can be converted to component video or S-video signals, and S-video signals can be converted to component video signals. However, you cannot convert the component video signals to standard video or S-video signals.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 12 Monday, March 28, 2005 4:08 PM 1c: Connecting components with only analog audio jacks Hooking up audio components For details on the required cords (A–H), see page 6.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 13 Monday, March 28, 2005 4:08 PM Hooking up video components Getting Started If you connect your TV to the MONITOR jacks, you can watch the video from the selected input (page 24).
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 14 Monday, March 28, 2005 4:08 PM 2: Connecting the antennas Connect the supplied AM loop antenna and FM wire antenna.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 15 Monday, March 28, 2005 4:08 PM 3: Connecting speakers Getting Started Connect your speakers to the receiver. This receiver allows you to use a 9.1 channel system. To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a center speaker, and two surround speakers) and a sub woofer (5.1 channel).
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 17 Monday, March 28, 2005 4:08 PM Tip Getting Started To connect certain speakers to another power amplifier, use the PRE OUT jacks. The same signal is output from both the SPEAKERS jacks and the PRE OUT jacks.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 18 Monday, March 28, 2005 4:08 PM Enjoying the 9.1 channel speaker system What is the 9.1 channel speaker system? A large dubbing theater for recording movie soundtracks uses 10 surround speakers. However, in a small dubbing theater, only 2 speakers each are placed on the right, left, and back walls.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 19 Monday, March 28, 2005 4:08 PM Connect the supplied AC power cord to the AC IN terminal on the receiver, then connect the AC power cord to a wall outlet. Before using the receiver Performing initial setup operations Before using the receiver for the first time, initialize the receiver by performing the following procedure.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 20 Monday, March 28, 2005 4:08 PM 5: Setting up the speakers You can use the SPEAKER SET UP menu to set the size and distance of the speakers connected to this system. 1 2 3 Press ?/1 to turn on the system. Rotate MAIN MENU to select “SPEAKER SET UP”. • YES If you connect a sub woofer, select “YES”.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 21 Monday, March 28, 2005 4:08 PM x SURROUND SP (Surround speakers) x SURR BACK SP (Surround back speakers) When the surround speakers size parameter is set to “NO”, the surround back speakers selection parameter is also automatically set to “NO” and the setting cannot be changed. • DUAL If you connect two surround back speakers, select “DUAL”.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 22 Monday, March 28, 2005 4:08 PM When placing two surround back speakers (The angle B should be the same) A 30˚ 100˚-120˚ 30˚ A 100˚-120˚ B B B x CENTER XX feet (Center speaker distance) Initial setting: 10 feet Lets you set the distance from your listening position to the center speaker. You can adjust from 3 to 23 feet in 1 foot steps.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB03CON_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 23 Monday, March 28, 2005 4:08 PM Getting Started 6: Adjusting the speaker levels and balance — TEST TONE Adjust the speaker levels and balance while listening the test tone from your listening position. Use the remote for the operation. Tip The receiver employs a test tone with a frequency centered at 800 Hz.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB04BSC_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 24 Monday, March 28, 2005 4:08 PM Amplifier Operation Selecting the component 1 Rotate INPUT SELECTOR to select the input. The selected input appears in the display.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB04BSC_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 25 Monday, March 28, 2005 4:08 PM Listening to FM/AM radio You can enter the frequency of the station you want directly. Use the remote for this operation. 1 Tip The tuning scale is: FM: 100 kHz AM: 10 kHz* * The AM tuning scale can be changed (see page 76). Automatic tuning 1 2 3 Rotate INPUT SELECTOR to select tuner (“FM” or “AM”).
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB04BSC_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 26 Monday, March 28, 2005 4:08 PM Presetting radio stations You can preset up to 30 FM or AM stations. Then you can easily tune in the stations you often listen to. Tuning to preset stations 1 2 Presetting radio stations 1 2 3 Rotate INPUT SELECTOR to select tuner (“FM” or “AM”). Switch the FM reception mode if necessary (page 25).
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB04BSC_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 27 Monday, March 28, 2005 4:08 PM Changing the display Amplifier Operation Changing the information in the display You can check the sound field etc. by changing the information in the display. Press DISPLAY repeatedly. Each time you press DISPLAY, the display will change as follows.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB04BSC_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 28 Monday, March 28, 2005 4:08 PM About the indications in the display 1 2 34 SW L C R L.F.E. SL S SR SBL SB SBR wg 5 6 8 9 q; qa INPUT AUTO I.LINK ; RF COAX OPT ANALOG MULTI IN 96/24 ; DIGITAL EX DTS-ES ; PRO LOGIC IIx NEO:6 DISCRETE H.A.T.S.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB04BSC_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 29 Monday, March 28, 2005 4:08 PM L SLEEP: Lights up when sleep timer is activated. M D.RANGE: Lights up when dynamic range compression is activated (page 46). O Tuner indicators: Lights up when using the receiver to tune in radio stations, etc. See pages 25–26 for tuner operations.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB05SND_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 30 Monday, March 28, 2005 4:08 PM Enjoying Surround Sound Using only the front speakers In this mode, the receiver outputs the sound from the front L/R speakers only. There is no sound from the sub woofer.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB05SND_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 31 Monday, March 28, 2005 4:08 PM Decoding the input audio signal automatically Press A.F.D. repeatedly to select “A.F.D. AUTO”. The receiver automatically detects the type of audio signal being input and performs the proper decoding if necessary. Tip In most cases, “A.F.D. AUTO” provides the most appropriate decoding.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB05SND_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 32 Monday, March 28, 2005 4:08 PM x Neo:6 Cinema Performs the DTS Neo:6 Cinema mode decoding. Selecting a sound field x Neo:6 Music Performs the DTS Neo:6 Music mode decoding. This setting is ideal for normal stereo sources such as CDs. x MULTI STEREO Outputs the 2 channel L/R signals from all speakers.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB05SND_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 33 Monday, March 28, 2005 4:08 PM x CINEMA STUDIO EX C DCS Reproduces the sound characteristics of the Sony Pictures Entertainment scoring stage. This mode is ideal for watching musicals or films where orchestra music is featured in the soundtrack. x V.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB05SND_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 34 Monday, March 28, 2005 4:08 PM x HEADPHONE (DIRECT) Press DIRECT. Outputs the signals without digital processing by the equalizer, sound field, etc. x HEADPHONE (MULTI) Selecting the surround back decoding mode Press MULTI CH. Outputs the analog signals input to the MULTI CH IN jacks.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB05SND_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 35 Monday, March 28, 2005 4:08 PM Input stream Output Applied surround channel back decoder Dolby Digital 5.1 5.1e) — Dolby Digital EXb) 6.1e) Matrix decoder depending on Surround Back Decoding Mode (SB DEC MODE), page 35 — DTS 5.1 5.1 DTS-ES Matrix 6.1c) 6.1e) DTS Matrix decoder DTS-ES Discrete 6.1d) 6.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB05SND_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 36 Monday, March 28, 2005 4:08 PM Input Stream indicator When AUTO FORMAT DIRECT mode is selected while the surround back decoder is activated, the current decoder’s process is displayed a few seconds after the input stream is displayed.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 37 Monday, March 28, 2005 4:08 PM Advanced Adjustments and Settings Selectable audio inputs for each input VIDEO 3 OPT Assigning the audio input VIDEO 1, VIDEO 2, VIDEO 3, TAPE DVD COAX, DVD OPT — DIGITAL ASSIGN You can assign the digital audio input for other input. This function is convenient in the following cases.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 38 Monday, March 28, 2005 4:08 PM Assigning the component video input — COMPONENT VIDEO ASSIGN You can assign a component video input for another visual input. 1 2 3 4 5 Switching the audio input mode for digital components — INPUT MODE Rotate MAIN MENU to select “CUSTOMIZE”.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 39 Monday, March 28, 2005 4:08 PM Customizing sound fields By adjusting the SURR SET UP menu and LEVEL menu, you can customize the sound fields to suit your particular listening situation. Adjusting the LEVEL menu You can adjust the balance and level of each speaker. These settings are applied to all sound fields.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 40 Monday, March 28, 2005 4:08 PM x MULTI CH SW XXX dB (Multi channel input sub woofer level) Initial setting: 0 dB Lets you increase the level of the MULTI CH IN sub woofer channel by +10 dB. This adjustment may be necessary when connecting a DVD player to the MULTI CH IN jacks.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 41 Monday, March 28, 2005 4:08 PM x CENTER MID XXX Hz (Center speaker midrange frequency) Initial setting: 1 kHz You can adjust from 100 Hz to 10 kHz in 5 steps (100 Hz, 300 Hz, 1 kHz, 3 kHz, 10 kHz). x CENTER TREBLE XXX dB (Center speaker treble level) x SURR/SB BASS XXX dB (Surround/surround back speaker bass level) x SURR/SB TRE.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 42 Monday, March 28, 2005 4:08 PM x SB DEC MODE [XXXXXXX] (SB DEC MODE) You can use the CUSTOMIZE menu to set the SB DEC mode, see page 41. • DDEX • PLIIx MV • PLIIx MS Note This parameter is valid only in A.F.D. mode (page 30). x 9.1 CH SP SYSTEM [XXX] (9.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 43 Monday, March 28, 2005 4:08 PM x UP YUV HUE [XX] (Video hue level) Initial setting: 4 Lets you adjust the hue of the images when you upconvert the video or S-video signals to component video signals. You can adjust from 1 to 7.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 44 Monday, March 28, 2005 4:08 PM x SP POSI. (Surround speaker position)* Tip Lets you specify the location of your surround speakers for proper implementation of the surround effects in the Cinema Studio EX modes (page 32).
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 45 Monday, March 28, 2005 4:08 PM Advanced SURR SET UP menu parameters When “MENU EXPAND” is set to “ON”, all of the following parameters are displayed and adjustable. See page 39 for the SURR SET UP menu adjustments. Initial settings are underlined. EFFECT LEVEL C. WIDTH L_C_R* DIMENSION F_I_S* PANORAMA MODE* FRONT REVERB* SCREEN DEPTH* VIR.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 46 Monday, March 28, 2005 4:08 PM Advanced LEVEL menu parameters x D.RANGE COMP. (Dynamic range compressor) TEST TONE Lets you compress the dynamic range of the sound track. This may be useful when you want to watch movies at low volumes late at night. • OFF The dynamic range is not compressed.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 47 Monday, March 28, 2005 4:08 PM Custom install mode 1 2 Rotate MAIN MENU to select “CIS”. Rotate MENU to select the parameter. For details, see “CIS menu parameters” below. 3 4 Rotate –/+ to select the setting you want. Repeat steps 2 and 3 to adjust the other items. CIS menu parameters Initial settings are underlined.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB06ADV_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 48 Monday, March 28, 2005 4:08 PM Storing the adjusted settings — USER PRESET To use the USER PRESET 1 2 Press USER PRESET repeatedly to select the USER PRESET you want. Press MEMORY/ENTER. Note You can store the adjusted sound field settings, etc. as USER PRESET up to 3 and can easily apply.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB070TH_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 49 Monday, March 28, 2005 4:08 PM To create an index name Other Operations 1 Naming preset stations and inputs Rotate –/+ to select a character, then rotate MENU to move the cursor to the next position.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB070TH_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 50 Monday, March 28, 2005 4:08 PM Changing the command mode of the receiver This function is useful when you use 2 Sony receivers in the same room. 1 2 Turn off the receiver. Hold down INPUT MODE and press ?/1 to turn on the receiver. “COMMAND MODE [AVX]” appears in the display.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB070TH_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 51 Monday, March 28, 2005 4:08 PM Selecting the speaker system Set the SPEAKERS switch according to the front speakers you want to drive. To select A The speakers connected to the FRONT SPEAKERS A terminals. B The speakers connected to the FRONT SPEAKERS B terminals.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB070TH_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 52 Monday, March 28, 2005 4:08 PM Recording on a video tape You can record from a VCR, a TV, or an LD player using the receiver. You can also add audio from a variety of audio sources when editing a video tape. See the operating instructions of your VCR if you need help. 1 2 Select the program source to be recorded.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB070TH_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB070TH_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB070TH_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 55 Monday, March 28, 2005 4:08 PM CONTROL S Control System If you connect the CTRL S IN jack on another component to the CTRL S OUT jack on this unit Example Using CONTROL S Control System TV IN OUT VCR IN Tuner OUT Receiver I .
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 56 Monday, March 28, 2005 4:08 PM Operations Using the Remote RM-AAE001 You can use the remote RM-AAE001 to operate the components in your system. Before you use your remote Inserting batteries into the remote Insert R6 (size-AA) batteries with the + and – properly oriented in the battery compartment.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 57 Monday, March 28, 2005 4:08 PM Remote Button Operations Function Remote Button Display 3 Remote Shows the selected input, macro list and command mode of the remote. DISPLAY q; TV/VCR/ Selects information VCD player/ displayed on the TV LD player/ screen.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 58 Monday, March 28, 2005 4:08 PM Remote Button Operations Function Remote Button Operations Function MAIN MENU qh Receiver Selects the menu of the receiver. SLEEP wj Receiver Activates the sleep function and the duration which the receiver turns off automatically. SUBTITLE 6 DVD player Changes the subtitles.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 59 Monday, March 28, 2005 4:08 PM Remote Button Operations 1-9 5 and Receiver 0/10 6 CD player/ VCD player/ LD player/ DVD player/ MD deck/ DAT deck Function Remote Button Operations Use with SHIFT to preset radio station or tuning to preset stations and with D.TUNING for direct tuning.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 60 Monday, March 28, 2005 4:08 PM Remote Button Operations V/v/B/b q; VCR/ Selects a menu item. Satellite tuner/ DVD player/ Blu-ray disc recorder/ Hard disc recorder/PSX O q; Function VCD player/ Returns to the previous LD player/ menu or exits the menu.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 61 Monday, March 28, 2005 4:08 PM Selecting the command mode of the remote Set the remote command mode using the RM SET UP button and Easy scroll key (PUSH). Use a suitable tool to press the RM SET UP button. Selecting the command mode 1 2 3 4 5 Hold down RM SET UP and press ?/1. Move the Easy scroll key (PUSH) to select “MAIN”.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 62 Monday, March 28, 2005 4:08 PM To cancel programming Press RM SET UP during any step. The remote automatically exits the programming mode. To activate the input after programming Press the programmed button to activate the input you want.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 64 Monday, March 28, 2005 4:08 PM To control a satellite tuner or cable box Maker Code(s) SONY 801, 802, 803, 804 JERROLD/G.I. 806, 807, 808, 809, 810, 811, 812, 813, 814 PANASONIC 818 RCA 805, 819 S.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 65 Monday, March 28, 2005 4:08 PM 6 Press the appropriate button on the remote control to be learned to send the remote button code. Notes • You can program more than 80 keys for the Learning function. In some cases, you may not be able to program even if you have not programmed 80 buttons.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB08REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 66 Monday, March 28, 2005 4:08 PM Tip Performing several commands in sequence automatically (Macro Play) If programming is unsuccessful, check the following: – If the indicator does not light up in step 1, the batteries are weak. Replace both batteries. – If the indicator lights 4 times in quick succession in step 4, an error has occurred.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB09REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 67 Monday, March 28, 2005 4:08 PM Operations Using the Remote RM-US106A You can use the remote RM-US106A to operate 2ND ZONE out and 3RD ZONE out only. You cannot control the receiver directly with this remote.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB09REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 68 Monday, March 28, 2005 4:08 PM The tables below show the settings of each button. Remote Button Operations Function Remote Button Operations Function VIDEO 3 3 Receiver To select VCR. (VTR mode 2) CH/ Receiver Selects preset stations. VIDEO 4* 3 Receiver PRESET/ D.SKIP TV/VCR/ Selects preset channels.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB09REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 69 Monday, March 28, 2005 4:08 PM Notes • Some functions explained in this section may not work depending on the model. • The above explanation is intended to serve as an example only. Therefore, depending on the component the above operation may not be possible or may operate differently than described.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB09REM_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 70 Monday, March 28, 2005 4:08 PM Notes • If you do not press a button during step 2 through 4 within 60 seconds, the remote automatically exits the button assignment mode. Start again from step 1.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB09REM_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 71 Monday, March 28, 2005 4:08 PM 2nd (3rd) zone operations When using a Sony receiver as an amplifier in the 2nd (or 3rd) zone and it is connected to the main receiver using an IR repeater (not supplied) as shown below, the following operations are possible. • Switching the output source for the 2ND (or 3RD) ZONE OUT jacks.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 72 Monday, March 28, 2005 4:08 PM On cleaning Additional Information Precautions On safety Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 73 Monday, March 28, 2005 4:08 PM Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. There is no sound no matter which component is selected.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 74 Monday, March 28, 2005 4:08 PM There is no sound from the center speaker. • Make sure the sound field function is on (press A.F.D., MOVIE or MUSIC). • Select the CINEMA STUDIO EX mode (page 32). • Adjust the speaker level (page 23, 39). • Make sure the center speaker is set to either “SMALL” or “LARGE” (page 20).
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 75 Monday, March 28, 2005 4:08 PM Remote control The remote does not function. • Point the remote at the remote sensor on the receiver. • Remove any obstacles in the path between the remote and the receiver. • Replace all the batteries in the remote with new ones, if they are weak.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Left GB01COV_STR-DA3100ES-U.book Page 76 Monday, March 28, 2005 4:08 PM AM tuner section Inputs (Analog) PHONO Sensitivity: 2.5 mV Impedance: 50 k Ohms S/N3): 86 dB (A, 2.5 mV4)) MULTI CH IN, SA-CD/CD, TAPE, MD/DAT, DVD, TV/SAT, VIDEO 1, 2, 3 Sensitivity: 150 mV Impedance: 50 k Ohms S/N3): 100 dB (A, 150 mV4)) 3) INPUT SHORT. 4) Weighted network, input level.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 77 Monday, March 28, 2005 4:08 PM Supplied accessories FM wire antenna (1) AM loop antenna (1) AC power cord (1) Remote commander RM-AAE001 (1) Remote commander RM-US106A (1) R6 (size-AA) batteries (4) For details on the area code of the component you are using, see page 3. Design and specifications are subject to change without notice.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.book Page 78 Monday, March 28, 2005 4:08 PM List of button locations and reference pages How to use this page Use this page to find the location of buttons and other parts of the system that are mentioned in the text. Illustration number r DISPLAY wf (27) R Name of button/part R Reference page Main unit ALPHABETICAL ORDER A.F.D.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB010ADD_STR-DA3100ES-U.fm] masterpage:Right GB01COV_STR-DA3100ES-U.
lename[E:\SEM_Janet\Revision_DA3100ES\J9050000_2514877121STRDA3100ESU\251487 121\GB01COV_STR-DA3100ES-UIX.fm] masterpage:Left GB01COV_STR-DA3100ES-U.