Installation Guide
Table Of Contents
- Cover
- GB
- Map of GUI Menu System
- Connections & settings (multi room/single room)
- Preparing the receiver
- Connecting equipment
- Setting up the receiver
- Outputting a test tone from each speaker (Test Tone)
- Displaying a test screen (Test Picture)
- Adjusting the sound balance automatically (Auto Calibration)
- List of messages after Auto Calibration measurements
- Saving/loading settings of the receiver
- Updating the firmware with a USB flash drive
- Setting up through a web browser
- Using the PING button
- Using the hidden commands
- Accessories
- Others
- FR
- Carte du système de l’IGU
- Branchements et réglages (plusieurs pièces/pièce unique)
- Préparation de l’ampli-tuner
- Raccordement d’un équipement
- Raccordement d’un téléviseur 4K prenant en charge HDCP 2.2 sur un décodeur de flux 4K à l’aide d’un câble HDMI compatible 4K
- Raccordement sur une chaîne Hi-Fi
- Établissement d’une connexion pour PoE (Power over Ethernet) (uniquement pour STR-ZA3000ES)
- Établissement d’une connexion sur plusieurs zones
- Mixage d’entrées audio/vidéo distinctes (dernier mode vidéo)
- Réglage de l’ampli-tuner
- Reproduction d’une tonalité de test depuis chacune des enceintes (Test Tone)
- Affichage d’une mire (Test Picture)
- Réglage automatique de la balance du son (Auto Calibration)
- Liste des messages après les mesures d’Auto Calibration
- Enregistrement/chargement des réglages sur l’ampli-tuner
- Mise à jour du micrologiciel à l’aide d’une clé USB
- Configuration via un navigateur Web
- Utilisation du bouton PING
- Utilisation des commandes cachées
- Accessoires
- Autres
- ES
- Mapa del sistema de menú de la interfaz gráfica de usuario
- Conexiones y configuraciones (varias habitaciones/una sola habitación)
- Cómo preparar el receptor
- Cómo conectar el equipo
- Cómo conectar una TV 4K compatible con HDCP 2.2 a un transmisor de 4K utilizando un cable HDMI compatible con 4K
- Cómo enlazar un sistema de música de alta fidelidad
- Cómo realizar una conexión PoE (alimentación a través de Ethernet) (solo para STR-ZA3000ES)
- Cómo realizar una conexión de varias zonas
- Cómo combinar entradas de audio y video diferentes (último modo de video)
- Cómo configurar el receptor
- Cómo reproducir un tono de prueba por cada altavoz (Test Tone)
- Cómo mostrar una pantalla de prueba (Test Picture)
- Cómo ajustar el balance de sonido automáticamente (Auto Calibration)
- Lista de mensajes después de las medidas de Auto Calibration
- Cómo guardar o cargar la configuración del receptor
- Cómo actualizar el firmware con una unidad flash USB
- Cómo realizar la configuración a través de un navegador web
- Cómo utilizar el botón PING
- Cómo utilizar comandos ocultos
- Accesorios
- Otros
- GB
![](/manual/sony/str-za1000es/installation-guide-english-spanish-french/images/img-13.png)
13
GB
Connections & settings (multi room/single room)
Making a multi-zone connection
This receiver allows various multi-zone connections.
Sample setup
Output jack Connected device Connection method
HDMI OUT A TV Connection: Connect to the TV using the HDMI OUT A jack.
Operation of the receiver: Press HDMI OUT to select HDMI A.
HDMI OUT B TV Connection: Connect to the TV using the HDMI OUT B jack.
Setup menu: Select [Setup] - [HDMI Setup] - [HDMI Out B Mode] - [Zone2] from
the home menu.
Select [Setup] - [HDMI Setup] - [Zone2 Audio Out] - [Zone2 TV +
AMP] from the home menu.
SPEAKERS terminals
FRONT A
CENTER
SURROUND
5ch speakers and 1 or 2
subwoofer(s)
Connection: Connect the speakers and subwoofer(s).
Setup menu: Perform Auto Calibration and set the following settings.
Select [Setup] - [Speaker Setup] - [SB Speaker Assign] - [Zone2] from the home
menu.
Tip
•Select [Setup] - [Input Setup] - [In-Ceiling Speaker Mode] - [On] when you use
the in-ceiling speakers.
SPEAKERS terminals
SURROUND BACK (assigned
ZONE2)
2ch speakers Connection: Connect Zone 2 L/R speakers.
Setup menu: Perform Auto Calibration and set the following settings.
Select [Setup] - [Speaker Setup] - [SB Speaker Assign] - [Zone2] from the home
menu.
Mixing separate audio/video inputs (Last video mode)
The receiver can continuously output the input video image used most recently when an
audio-only input source is selected.
1 Connect the desired background music source to an input by analog, optical,
or coaxial cable. Or use the built-in tuner.
2 Set the input to the following in the Input Setup menu.
HDMI: [None]
Component: [None]
Composite: [---]
Audio: The input connected to the source.
When using the built-in tuner, set the screen mode to [Simple] using the options menu in
[FM/AM Display].
Example
Press SAT/CATV followed by TUNER to listen to sound from the built-in tuner while watching a
video source connected to SAT/CATV.
The audio output changes to that of the tuner source while SAT/CATV video output is
retained.