4-590-341-13 (1) UHF Synthesized Diversity Tuner Operating Instructions URX-S03D © 2016 Sony Corporation
Table of Contents Features .......................................................3 Parts Identification ......................................4 Preparation ..................................................5 Attaching to a Camcorder............................. 5 Using Wireless Adapters .............................. 5 Settings ........................................................5 Setting the Receive Channel.........................
Built-in infrared communication function When operating in conjunction with UWP-D series transmitters, the frequency and compander mode settings configured on the unit can be sent using the infrared communication function, allowing you to complete channel configurations quickly. Features The URX-S03D UHF Synthesized Diversity Tuner is a two-channel slot-in wireless tuner that can be used in conjunction with Sony professional camcorders and optional wireless adapters.
h SET button Changes the item to be set or enters the selected function or parameter value. Parts Identification i + or – button Use to select a function or value. j Infrared transmission port Transmits the frequency and compander mode settings configured on the unit to the transmitter. k Display section Meter display A Audio input level meter Indicates the input signal level. B Peak indicator Warns of excessive input by lighting up when the signal is 3 dB below the level at which distortion begins.
Preparation Settings Attaching to a Camcorder Setting the Receive Channel This receiver can be inserted into a slot provided on compatible Sony camcorders. For details about the channel groups and channels that can be selected, refer to the “Frequency List” on the CD-ROM. 1 Remove the cover from the slot for the wireless receiver on the camcorder, and insert the receiver into the slot. Note To prevent interference and noise, beware of the following.
Searching for Active Channels within a Group (Active Channel Scan) Notes • If there is no user input within 10 seconds after the channel group display or channel number display starts flashing, the displayed setting that is flashing is saved. The same applies when setting other parameters. • The frequency indicator changes in response to the channel number. • The unit continues to receive, even when setting the receive channel.
Transmitter Notes • When operating in conjunction with UWP-D series transmitters, set the transmitters to the same compander mode. • No audio will be output if the tone signal frequency is different due to inconsistencies in compander mode settings configured on the devices being used together. • When the squelch function (page 7) is set to OFF, audio will be output even when compander mode settings are not consistent. However, phenomena, such as changes in output level, may occur in such cases.
6 Note This function cannot be used when operating in conjunction with UWP or WRT series transmitters. Use the + or – button to select “YES,” then press the SET button on the transmitter. This sets the transmit channel and compander mode. Notes Searching for available channels and configuring the channel settings via infrared communication (AUTO SET) 1 Press the MENU button to display the RX1 or RX2 menu, and press the + or – button to display the AUTO SET screen.
Basic Menu Operations Menu Displays and Detailed Settings Menu name Function name Menu Structure and Hierarchy Menu structure UTILITY menu You can display the UTILITY menu from the meter screen which displays information on tuners 1 and 2. This menu allows you to configure basic settings for the unit and settings for when the unit is used in conjunction with a wireless adapter. Item to be set 1 RX1 (tuner 1) menu This menu allows you to configure settings for RX1 (tuner 1).
OFF: 75-ohm termination is not added. wireless adapter and you are using the OUTPUT 2 connector of the DWA-01D for AES/EBU output, select the signal to be used as the OUTPUT 1 connector’s sub output. Note When the receiver is turned off, the termination is released. Notes • OUTPUT 2 settings cannot be configured. • Adjust the volume for each channel using the attenuator function on the transmitter.
For details, see “Using the Squelch Function” (page 7). For details, see “Setting the Receive Channel” (page 5). Setting an available channel automatically (AUTO SET) Automatically search for and set an available channel, and start infrared transmission to the transmitter. For details, see “Searching for available channels and configuring the channel settings via infrared communication (AUTO SET)” (page 8). Selecting the frequency band (BAND) Select the receive frequency band.
Error Messages When a problem occurs, one of the following error messages may appear on the display. Message Meaning Solution EEP ERROR An error has Contact your Sony occurred in the service representative. backup memory data. PLL ERROR An error occurred in the PLL synthesizer circuit. Restart the unit. If the message persists, contact your Sony service representative.
Troubleshooting If you have any problem, use the following checklist before asking for repairs. If the problem persists, contact your Sony service representative. Symptom Cause Solution The unit does not turn The unit is not correctly inserted into the slot of the Insert the unit until it is firmly and completely in, on. camcorder or the wireless adapter. and then secure it with the mounting screws. There is no sound. The channel setting on the transmitter is different from that on the receiver.
Important Notes on Use Specifications Antenna connector BNC-R, 50 Ω (2) RF squelch level 15 dBµ / OFF (0 dBµ = 1 µV) Audio output level –40 dBu (0 dBu = 0.775 Vrms with modulating frequency of 1 kHz and frequency deviation of ±5.
Dimensions 31.2 (1 1/4) 116.2 (4 5/8) 88 (3 1/2) 88 × 116.2 × 31.2 mm (3 1/2 × 4 5/8 × 1 1/4 in.) (width / height / depth) Mass Approx. 303 g (11 oz.) (with supplied antennas attached) Supplied accessories Whip antenna (2) Before Use (1) CD-ROM (1) Warranty card (1) Design and specifications are subject to change without notice. Notes • Always verify that the unit is operating properly before use.
Sony Corporation