user manual
Table Of Contents
- Introduction
- Optimizing for Sound Forge
- Learning the Sound Forge Workspace
- Getting Started
- Navigating, Zooming, and Selecting
- Changing File Attributes and Formats
- Using Markers, Regions, and the Playlist/Cutlist
- Why use markers, regions, and the playlist?
- Using markers
- Using command markers in streaming media files
- Using regions
- Using the Regions List
- Using the playlist
- Displaying the playlist
- Adding regions to the playlist
- Understanding the playlist display
- Customizing the playlist display
- Repeating a region during playlist playback
- Playing from the playlist
- Arranging the playlist
- Replicating a region in the playlist
- Using stop points
- Deleting a region from the playlist
- Creating a new file from the playlist
- Configuring the playlist as a cutlist
- Saving a playlist/cutlist file
- Opening a playlist/cutlist file
- Copying the playlist/cutlist to the clipboard
- Recording, Extracting, and Burning
- Recording audio
- Recording manually
- Recording automatically
- Recording a specific length (punch-in)
- Choosing a recording mode
- Adjusting for DC offset
- Playing back recorded audio
- Using remote recording mode
- Synchronizing with other devices
- Viewing input levels
- Inserting markers while recording
- Configuring gap detection
- Automatically labeling windows and regions
- Changing blinking status
- Extracting audio from CDs
- Burning CDs
- Proper use of software
- Recording audio
- Editing, Repairing, and Synthesizing Audio
- Processing Audio
- Applying Effects
- Adding an effect
- Adding a chain of effects
- Applying effects using the Plug-In Chainer
- Adding plug-ins to a chain
- Selecting the processing mode for audio tail data
- Arranging plug-ins on a chain
- Bypassing effects
- Removing plug-ins from a chain
- Configuring chained plug-ins
- Saving individual plug-in settings as a custom preset
- Saving plug-in chains
- Loading plug-in chains
- Managing effects
- Automating Effect Parameters
- Adjusting envelopes
- Using Acoustic Mirror and Wave Hammer
- Working with MIDI/SMPTE
- Sampling
- Looping
- Working with Video
- Using Spectrum Analysis
- Working in the frequency domain
- Using a spectrum graph
- Displaying a spectrum graph
- Monitoring an input and output source
- Displaying frequency and amplitude values, notes and statistics
- Navigating a spectrum graph
- Changing the graph type
- Changing the zoom level
- Working with stereo files
- Updating a spectrum graph
- Viewing multiple spectrum graphs
- Creating and comparing snapshots of the Spectrum Analysis window
- Printing the graph
- Using a sonogram
- Adjusting Spectrum Analysis settings
- Shortcuts
- Microsoft Audio Compression Manager
- SMPTE Timecode
- Using CSOUND, MTU, IRCAM, BICSF, and EBICSF Files
- Index
CHP. 5 NAVIGATING, ZOOMING, AND SELECTING
75
Changing the level zoom
To edit the level ruler zoom, use the Zoom In/Out spinner control located above the playbar.
• Clicking the magnifying glass buttons increases/decreases the level ruler
zoom by single-step increments.
• Dragging the spin control increments the level ruler zoom quickly in the corresponding direction.
At high zoom levels, only low-level samples are visible because the peaks of the waveform move beyond the
vertical scope of the data window. Consider the following data windows.
Both data windows display the same audio file at a 1:1 zoom ratio. The window on the left shows the level
ruler zoomed to its maximum out position. The window on the right shows the level ruler zoomed to its
maximum in position. Notice that wave peaks clearly visible in the left window are out of display range in
the right window.
Using zoom level commands
If you prefer using commands, you can control the level magnification from the View menu. The following
table briefly describes the three available zoom level commands. You can access these commands from the
View menu by choosing Zoom Level and choosing the desired command from the submenu.
Formatting the level ruler
You can configure the level ruler to display in decibels or percent by right-clicking the ruler and choosing
Label in Percent or Label in dB from the shortcut menu.
Using custom zoom settings
You can create two custom time zoom settings for quick access to time magnification levels that you use
frequently.
Creating custom zoom settings
1.
From the Options menu, choose Preferences. The Preferences dialog appears.
2.
Click the Display tab.
3.
Select time magnification settings from the Custom zoom ratio 1 and Custom zoom ratio 2 drop-down lists.
4.
Click OK.
Zooming to custom settings
From the View menu, choose Zoom Time, and choose a custom zoom setting from the submenu.
Click a
Custom Zoom button ( or ) on the Navigation toolbar or press or on the numeric
keypad.
Out Full Decreases the zoom level to minimize the display of the file’s amplitude.
Window Changes the level zoom to display the entire waveform amplitude in the data window.
Selection Maximizes the display of the selection (vertically and horizontally) in the data window.
Level zoom out maximum Level zoom in maximum
1 2