SONY. Bluetooth® Audio System 4-699-684-11{1) Operating Instructions Mode d'emploi Owner's Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the sp.ace provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. WX-920BT Serial No. ------- To cancel the demonstration (DEMO) display, see page 19. For the connection/installation, see page 33.
For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use. ·For details, see "Connection/Installation" (page 33). This product is classified as a Class 1 Laser product under IEC/EN 60825-1:2007 and IEC/EN 608251:2014 and Class I Laser product under 21 CFR Part 1040.10. • Emission Duration: Continuous • Laser Output: Less than 55.8 ~W • Wavelength: 775 nm to 800 nm The nameplate indicating operating voltage, etc.
Warning if your car's ignition has no ACC position Be sure to set the AUTO OFF function (page 20}. The unit will shut off completely and automatically in the set time after the unit is turned off and the clock is displayed (i.e. press and hold SRC for 1 second}, which prevents battery drain. If you do not set the AUTO OFF function, press and hold OFF until the display disappears each time you turn the ignition off.
Additional Information Table of Contents Warning ................................... 2 Guide to Parts and Controls ................... 5 Getting Started Resetting the Unit ........................... 7 Setting the Clock ............................ 7 Checking the Battery Voltage ................. 7 Preparing a BLUETOOTH Device ................ 7 Connecting a USB Device ..................... 9 Connecting Other Portable Audio Device ....... 10 Listening to the Radio Listening to the Radio .... ·...........
Guide to Parts and Controls Main unit [] Q (browse) (page 12, 14, 15) Enter the browse mode during playback. (Not available when a USB device in Android mode or iPod is connected .} [1] ~(disc eject) [ID ::1::' (SEEK-/+) Tune in radio stations automatically. Press and hold to tune manually. ~I~ (prev/next) ~~~ (fast-reverse/fast-forward) PTY (program type) Select PTY in RDS. [2] SRC (source) Turn on the power. Change the source.
c:; (repeat) (Not available when a USB device in Android mode is connected.) ~(shuffle} {Not available when a USB device in Android mode is connected.) MIC (page 17} ...,.... (play/pause) ~ Control dial Rotate to adjust the volume. PUSH ENTER Enter the selected item. Press SRC, rotate then press to change the source (timeout in 2 seconds). MENU Open the setup menu.
Before connecting the device, turn down the volume of this unit; otherwise, loud sound may result. Getting Started Resetting the Unit Before operating the unit for the first time, after replacing the car battery, or changing the connections, you must reset the unit. 1 Press DSPL and CALL\. for more than 2 seconds. Note Resetting the unit will erase the clock setting and some stored contents. Setting the Clock 1 Press MENU, rotate the control dial to select [GENERAL], then press it.
7 If passkey* input is required on the BLUETOOTH device, input [0000]. * Passkey may be called "Passcode," "PIN code," "PIN number" or "Password," etc., depending on the device. When connecting a BLUETOOTH device for the first time, mutual registration (called "pairing") is required. Pairing enables this unit and other devices to recognize each other. This unit can connect two BLUETOOTH devices (two cellular phones, or a cellular phone and an audio device).
Icons in the display: ~" m" Lights up when handsfree calling is available by enabling the HFP {Handsfree Profile). Lights up when the audio device is playable by enabling the A2DP (Advanced Audio Distribution Profile). To connect the last-connected device from this unit Activate the BLUETOOTH function on the BLUETOOTH device. To connect with the audio device, press SRC to select [BT AUDIO] and press ...,.II {play/pause). To connect with the cellular phone, press CALL.
Connecting Other Portable Audio Device Listening to the Radio 1 Turn off the portable audio device. Listening to the Radio 2 Turn down the volume on the unit. To listen to the radio, press SRC to select [TUNER]. 3 Connect the portable audio device to the AUX input jack (stereo mini jack) on the unit with a connecting cord (not supplied)*. * Be sure to use a straight type plug. 1 Press MODE to change the band (FM1, FM2, FM3, AM1 or AM2).
Using Radio Data System (RDS) Listening to the SiriusXM Radio 1 2 Only SiriusXM brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Connect Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com Press PTY during FM reception.
To change the passcode 1 Press Q (browse). 2 Rotate the control dial to select [CHANNEL], then press it. 3 Rotate the control dial to select the desired channel, then press it. To select channels with rapid browse mode Press and hold t or .. of remote commander more than 2 seconds after [CHANNEL] selected, then press ENTER. To select channels from categories Press Q (browse). 1 2 3 4 Rotate the control dial to select [CATEGORY], then press it.
Playback Before making a connection, select the USB mode (Android mode or MSC/MTP mode) depending on the USB device (page 20). 1 Playing a Disc 1 Connect a USB device to the USB port (page 9). Playback starts. If a device is already connected, to start playback, press SRC to select [USB] ([I POD] appears in the display when the iPod is recognized). Insert the disc {label side up). 2 Adjust the volume on this unit. To stop playback Press and hold OFF for 1 second.
To match the volume level of the BLUETOOTH device to other sources Start playback of the BLUETOOTH audio device at a moderate volume, and set your usual listening ·volume on the unit. Press MENU, then select [SOUND]-+ [BTA VOLUME] (page 21). Searching and Playing Tracks Not available when a USB device in Android mode or iPod is connected. 1 During CD or USB playback, press Q (browse). 2 Press..._ (SEEK+). 3 Rotate the control dial to select the item.
Listening to Pandora@ Pandora® is available to stream music through your iPhone and Android smartphone. You can control Pandora® on a BLUETOOTH connected iPhone/ Android smartphone from this unit. Pandora® is only available in certain countries. Please visit http:/ /www.pandora.com/legal for more information. Setting up Pandora® 1 2 Check the compatibility of your mobile device by visiting the support site on the back cover.
5 Handsfree Calling (via BLUETOOTH The phone call starts. only} To use a cellular phone, connect it with this unit. You can connect two cellular phones to the unit. For details, see "Preparing a BLUETOOTH Device" (page 7). Rotate the control dial to select a number from the number list, then press it. 1 Press CALL. When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it. 2 Rotate the control dial to select [RECENT CALL], then press it.
You can make a call by saying the voice tag stored in a connected cellular phone that has a voice dialing function. 1 Press CALL When two cellular phones are connected to the unit, rotate the control dial to select either phone, then press it. 2 Rotate the control dial to select (VOICE DIAL], then press it. Alternatively, press and hold VOICE for more than 2 seconds. 3 Say the voice tag stored on the cellular phone. Your voice is recognized, and the call is made. To cancel voice dialing Press VOICE.
Selecting the source or application You can operate to select the desired source or application on iPhone/ Android smartphone. Using Voice Recognition (Android smartphone only) To select the source 1 Press and hold VOICE to activate voice recognition. 2 Say the desired voice command into the microphone. Press SRC repeatedly. Alternatively, press SRC, rotate the control dial to select the desired source, then press ENTER. To display the source list Press SRC.
To deactivate Siri Eyes Free Press VOICE. Notes • The iPhone may not recognize your voice depending on usage conditions. (For example, if you are in a moving car.) • Siri Eyes Free may not function properly, or the response time may lag in locations where iPhone signals are difficult to receive. • Depending on the iPhone's operating condition, Siri Eyes Free may not function properly, or may quit.
AUTO OFF (auto off) Shuts off automatically after a certain time when the unit is turned off and the clock is displayed (i.e. press and hold SRC for 1 second): [ON] (30 minutes), [OFF]. STEERING (steering) Registers/resets the setting of the steering wheel remote control. (Available only while the source is off and the clock is displayed.} STR CONTROL (steering control} Selects the input mode of the connected remote control.
E010 CUSTOM (EQ10 custom} Sets (CUSTOM] of EQ10. Setting the equalizer curve: [81] 32 Hz, [82] 63Hz, (83} 125Hz, [84} 250Hz, [85] 500 Hz, [86] 1 kHz, [87] 2kHz, [B8] 4kHz, [B9] 8kHz, [B10] 16kHz. The volume level is adjustable in 1 dB steps, from -6 dB to +6 dB. BALANCE (balance) Adjusts the sound balance: [RIGHT-15][CENTER]- [LEFT-15]. FADER (fader) Adjusts the relative level: [FRONT-15]- [CENTER] - [REAR-15].
BLUETOOTH Setup {BLUETOOTH) Additional Information PAIRING (pairing) (page 8) · Connects up to two BLUETOOTH devices: [DEVICE 1], [DEVICE 2]. [DEVICE 1] or [DEVICE 2] will be changed to the paired device name after pairing is complete. AUDIO DEV (audio device) Selects the audio device. [*] appears on the device paired with [DEVICE 1] or the current A2DP compatible audio device.
• Discs that this unit CANNOT play - Discs with labels, stickers, or sticky tape or paper attached. Doing so may cause a malfunction, or may ruin the disc. -Discs with non-standard shapes (e.g., heart, square, star). Attempting to do so may damage the unit. - 8 em (3 1/4 in) discs. Notes on CD-R/CD-RW discs • If the multi-session disc begins with a CD-DA session, it is recognized as a CO-DA disc, and other sessions are not played. • Discs that this unit CANNOT play - CD-R/CD-RW of poor recording quality.
Specifications FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC. POUR LES CLIENTS AUX ETATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA PROVINCE DE QUEBEC. AUDIO POWER SPECIFICATIONS CTA2006 Standard Power Output: 20 Watts RMS x 4 at 4 Ohms< 1% THD+N SN Ratio: 80 dBA (reference: 1 Watt into 4 Ohms) Tuner section FM Tuning range: 87.5 MHz -107.
Dimensions: Approx. 178 mm x 100 mm x 177 mm {71/s in x 4 in x 7 in) (w/h/d) Mounting dimensions: Approx. 182 mm x 111 mm x 159 mm {7 1/4 in x 4 3/s in x 6 3/s in) (w/h/d) Mass: Approx. 1.
Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. For details on using the fuse and removing the unit from the dashboard, see "Connection/In stallation" (page 33}. If the problem is not solved, visit the support site on the back cover. No power is being supplied to the unit.
~ You cannot play items via a USB hub. ~ This unit cannot recognize USB devices via a USB hub. A USB device takes longer to play. The USB device contains files with a complicated tree structure. ~ The sound is intermittent. ~ The sound may be intermittent at a high-bit-rate. ~ DRM (Digital Rights Management) files may not be playable in some cases. The audio file cannot be played. ~ USB device formatted with file systems other than FAT16 or FAT32 are unsupported.
The phone is not connected. ~ When BLUETOOTH audio is played, the phone is not connected even if you press CALL. -Connect from the phone. The phone sound quality is poor. ~ Phone sound quality depends on reception conditions of cellular phone. - Move your car to a place where you can enhance the cellular phone's signal if the reception is poor. The volume of the connected audio device is low (high). ~ Volume level will differ depending on the audio device.
Messages The following messages may appear or flash during operation. INVALID ~ The selected operation could be invalid. READ: Now reading information. ~ Wait until reading is complete and playback starts automatically. This may take some time depending on the file organization. _ (underscore): The character cannot be displayed. For CD playback: USB NO DEVICE: A USB device is not connected or recognized. Make sure the USB device or USB cable is securely connected.
For Sony 1 Music Center operation: APP -----------: A connection with the application is not established. Make the "Sony 1 Music Center" connection again (page 17). ~ APP DISPLAY: A screen setting display of the application is open. Exit the screen setting display of the application to enable button operation. ~ APP LIST: The contents list of the CD/USB/iPod is open. Exit the list of the application to enable button operation. ~ APP MENU: A setting display of the application is open.
For SiriusXM operation: INCORRECT PASS CODE ENTERED ~ CHANNEL LOCKED ~ The channel that you have requested is locked by the radio parental control feature. See "To set a parental control" (page 12) for more information on the parental control feature and how to access locked channels. CHANNEL NOT AVAILABLE ~ ~ The channel that you have requested is not a valid SiriusXM channel or the channel that you were listening to is no longer available.
For steering wheel remote control operation: ERROR: An error occurred during the function registration. ~ Register again from the function where the error occurred (page 20). TIMEOUT: The function registration failed due to a timeout. ~ Try completing the registration while [REGISTER] is blinking (about 6 seconds) (page 20). For firmware update operation: FILE ERROR: The updater is not stored in the USB device. ~ Store the updater in the USB device, then try again (page 22).
Con nection/1 nstallation Parts List for Installation ® Cautions • Run all ground (earth) leads to a common ground (earth) point. • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power supply leads only after all other leads have been connected. • Be sure to insulate any loose unconnected leads with electrical tape for safety. Sxmax. Smm (7/32 x max.
Connection Subwoofer*1 ................................. ~ iLJi\. [ 2 White Front speaker*1*2 Gray Gray/black striped Green Green/black striped Purple Purple/black striped Black Yellow Red Blue/white striped Orange/white striped =+ ®m 0 =+ ~ID 0 =+ ~ o....,...,.,.,., 0 =+ ~ID 0 O+ e O+ + e 0 O+ + e 0 White/black striped GND ~ BATTERY ACC REM OUT (MAX 0.4A) ILLUMINATION For details, see "Making connections· (page 35). : •...................•.••.•••.. ••...•......................... ...............
Speaker connection 0 To a common ground {earth) point First connect the black ground (earth) lead, then connect the yellow and red power supply leads. • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 Q to 8 Q, and with adequate power handling capacities to avoid damage. f) To the +12 V power terminal which is energized at all times Be sure to first connect the black ground (earth} lead to a common ground (earth) point.
Notes on installing the connection cable RC-SR1 (not supplied) • Refer to the support sites on the back cover for details, then connect each lead properly to the appropriate leads. Making an improper connection · may damage the unit. • Depending on the type of car, be sure to insulate the unused leads with electrical tape for safety. • Do not connect this cable when the steering wheel remote control is not used. • Consulting the dealer or an experienced technician for help is recommended.
http://esupport.son y.com/ 1 Read Troubleshooting in these Operating Instructions .. 2 Please contact (U.S.A. only); Call 1-800-222-7669 URL http://www.SONY. com .J News & Alerts I Actus & Alertes .J Software updates I Mises ajour .J Tutorials I Didacticiels .J Tips & Tricks I Conseils & Astuces https:/ /sony.net/SBS llilO~@ DIGITAL AUDIO I TEXT I Made for ~ iPod ©2017 Sony Corporation DiPhone pandora® Printed in Thailand http:/ /www.sony.
SON Yo 4-467-585-01 For Dealers For display purposes it is necessary to secure the front panel to the unit as shown below. S~ecure the screw on the left side of the unit.
GARANTIE LIMITEE E.-U. et Canada uniquement - 1 an Sony Electronics Inc. exclusivement pour les achats effectues aux Etats-Unis et Sony du Canada Ltee. exclusivement pour les achats effectues au Canada (collectivement " Sony ") garantit ce produ~ contre les defauts de materiaux ou de fabrication pour le proprietaire d'origine et tousles proprietaires utilisateurs finaux suivants (" Vous " ou " Vos ")pendant Ia periode definie cidessus et comme indique dans les presentes.
111111111111111111111111111111111111111111111111111111111111 4-597-059-11 LIMITED WARRANTY Car Audio U.S. and Canada only - 1 year Sony Electronics Inc. solely for purchases made in the United States and Sony of Canada Ltd. solely for purchases made in Canada (collectively "Sony'') warrants this product against defects in material or workmanship for the original owner and any subsequent end user owner(s) ("You" or ''Your") for the time period set forth above as set forth herein.