Owner's Manual

Troubleshooting
The
following
checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
For
details on using the fuse and removing the
unit
from the dashboard,
see
"Connection/Installation"
(page
33}
.
If
the problem
is
not solved, visit the support site on
the back cover.
No power
is
being
supplied
to the unit.
~
If
the
unit
is
turned
off
and the display
disappears, the unit cannot be operated
with
the
remote commander.
-Turn
on the unit.
No sound or the sound
is
very low.
~
The position
of
the fader control
[FADER]
is
not
set for a 2-speaker system.
~
The
volume
of
the unit
and/or
connected device
is
very low.
-
Increase
the volume
of
the
unit
and connected
device.
No beep sound.
~An
optional power amplifier
is
connected and
you are
not
using the built-in amplifier.
The contents
of
the memory have been erased.
~
The
power
supply lead or battery
has
been
disconnected or not connected properly.
Stored stations and correct time are erased.
The fuse has
blown.
Makes a noise when
the
position
of
the ignition
is
switched.
~
The
leads are
not
matched correctly with the car's
accessory power connector.
During playback or reception, the demonstration
mode starts.
~
If
no operation
is
performed for
5
minutes
with
[DEMO-ON] set, the demonstration mode starts.
-Set
[DEMO-OFF] (page
19}.
The
display disappears from/does not appear in
the
display
window.
~The
dimmer
is
set
to
[DIMMER-ON]
(page
21}.
~
The display disappears
if
you press and hold
OFF.
-
Press
OFF
on the unit until the display appears.
The display/illumination flashes.
~
The
power
supply
is
not sufficient.
-Check
that
the car battery supplies enough
power
to
the unit. (The power requirement
is
12
V
DC.}
26GB
The operation buttons do not function.
The disc will
not eject.
~
The connection
is
not
correct.
-
Press
DSPL
and
CALL\.
for
more than 2
seconds
to
reset the
unit
(page
7}.
The contents stored in
memory
are erased.
For
your safety, do not reset the unit while you
are driving.
Stations cannot be received.
The sound
is
hampered by noises.
~
The
connection
is
not
correct.
-If
your car
has
built-in radio antenna (aerial}
in
the rear /side glass, connect an
REM
OUT
lead
(blue/white
striped) or accessory power supply
lead (red}
to
the power supply lead
of
a car's
antenna (aerial} booster.
-Check
the connection
of
the car antenna
(aerial} . .
·
-If
the auto antenna (aerial}
will
not
extend,
check the connection
of
the
power
antenna
(aerial} control lead.
Preset tuning
is
not possible.
~
The broadcast signal
is
too weak.
PTY
displays[--------].
~
The current station
is
not
an
RDS
station.
~
RDS
data has
not
been received.
~
The station does
not
specify the program type.
The
disc
does not
play.
~
Defective or dirty disc.
~The
CD-R/CD-RW
is
not
for
audio use (page
23}.
MP3/WMA
files
cannot be played.
~
The disc
is
incompatible
with
the MP3/WMA
format and version.
For
details on playable discs
and formats, visit the support site on the back
cover.
MP3/WMA
files
take
longer
to
play
than others.
~
The
following
discs take a longer
time
to
start
playback.
-A
disc recorded
with
a complicated tree
structure.
-A
disc recorded in Multi Session.
-A
disc
to
which data can be added.
The sound skips.
~
Defective or dirty disc.