4-164-312-11 (1) AV Center AV Center Operating Instructions US Mode d’emploi FR Manual de instrucciones ES Owner’s Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XAV-60 Serial No.
Be sure to install this unit in the dashboard of the car for safety. For installation and connections, see the supplied installation/ connections manual. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For the State of California, USA only Warning To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet.
Table of Contents Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Notes on installation. . . . . . . . . . . . . . . . . . . . . . 7 Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Playable discs and symbols used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Location and function of controls . . . . . . . . . . 10 Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Card remote commander RM-X170 . . . . . .
iPod Operations Monitor Adjustment Playing an iPod . . . . . . . . . . . . . . . . . . . . . . . . 31 Touch panel calibration . . . . . . . . . . . . . . . . . 37 Setting the play mode . . . . . . . . . . . . . . . . . . . 31 Setting the background screen . . . . . . . . . . . . 37 Repeat and shuffle play . . . . . . . . . . . . . . . . . . 32 Selecting the picture quality — Picture EQ . . . . . . . . . . . . . . . . . . . . . . . . . 38 Customizing the picture quality . . . . . . . . .
Additional Information Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Notes on LCD panel . . . . . . . . . . . . . . . . . . 48 Notes on discs . . . . . . . . . . . . . . . . . . . . . . . 48 Playback order of MP3/WMA/AAC/JPEG/ MPEG-4 files. . . . . . . . . . . . . . . . . . . . . . . .49 About MP3 files . . . . . . . . . . . . . . . . . . . . . 49 About WMA files . . . . . . . . . . . . . . . . . . . .49 About AAC files . . . . . . . . . . . . . . . . . . . . . 49 About JPEG files .
Notes on safety • Comply with your local traffic rules, laws and regulations. • While driving – Do not watch or operate the unit, as it may lead to distraction and cause an accident. Park your car in a safe place to watch or operate the unit. – Do not use the setup feature or any other function which could divert your attention from the road. – When backing up your car, be sure to look back and watch the surroundings carefully for your safety, even if the rear view camera is connected.
12 TONE ANALYSIS and its logo are trademarks of Sony Corporation. “WALKMAN” and “WALKMAN” logo are registered trademarks of Sony Corporation. SensMe and the SensMe logo are trademarks or registered trademarks of Sony Ericsson Mobile Communications AB. Music recognition technology and related data are provided by Gracenote®. Gracenote is the industry standard in music recognition technology and related content delivery. For more information, please visit www.gracenote.com.
Playable discs and symbols used in this manual This unit can play various video/audio discs. The following chart helps you to check if a disc is supported by this unit, as well as what functions are available for a given disc type. Disc symbol in manual Disc format DVD VIDEO VIDEO DVD-R*1 / DVD-R DL*1 / DVD-RW*1 (Video mode/VR mode) DVD+R*1 / DVD+R DL*1 / DVD+RW*1 AUDIO Video CD (Ver. 1.0/1.1/2.0) Audio CD CD-ROM*2 / CD-R*2 / CD-RW*2 *1 Audio files can also be stored.
Location and function of controls Main unit Refer to the pages listed for details. F Volume control dial A Z (Eject) button page 17 C Receptor for the card remote commander G SOURCE/OFF button* Press to turn on the power/change the source: “Tuner” (Radio), “Disc,” “AUX” (Auxiliary equipment), “USB/iPod.” Press for 1 second to turn off the power. Press for more than 2 seconds to shut off completely. D Disc slot page 17 H Display window/touch panel E TOP button To open the source list.
A “Source List” key To open the source list. Screen displays When no source is selected: 1 2 Source List Top B “Top” key To open the source list. C Clock display page 43, 46 D (Close) key To close the menu. E “ATT” (Attenuate) key*1 To attenuate the sound. To cancel, touch again. 12:00 3 Source list: 4 5 6 7 M.OFF ATT Tuner USB/iPod Disc SensMe™ F (Setting) key To open the setting menu. G “M.OFF” (Monitor off) key To turn off the monitor and the button illumination.
Card remote commander RM-X170 8 1 9 2 q; 3 qa 4 5 qs qd qf 6 7 • The card remote commander can be generally used to operate the audio controls simply. For menu operations, use the touch panel. • Refer to the pages listed for details. • Remove the insulation film before use (page 14). A OFF button Press to turn off/stop the source. Press and hold to shut off completely.
J .m/M> buttons Radio: Press to tune in stations automatically. Press and hold to find a station manually. Disc*2/USB: Press to skip a chapter/track/scene/file. Press and hold momentarily to reverse/fastforward the video. Press and hold to reverse/fast-forward track. K DVD playback setting buttons (AUDIO): To change the audio language/format. (For VCD/CD/MP3/WMA/AAC/MPEG-4, to change the audio channel.) (SUBTITLE): To change the subtitle language. (ANGLE): To change the viewing angle.
Getting Started Preparing the card remote commander Resetting the unit Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Press the reset button (page 10) with a pointed object, such as a ball-point pen. Note Pressing the reset button will erase the clock setting and some stored contents. Performing initial settings After resetting, the display for the initial settings appears.
Basic Operations Listening to the radio 1 Touch “Source List,” then “Tuner.” Source List ATT Top The radio reception display appears. P1 P2 P3 BTM P4 P5 P6 Memory Band Receive Menu Preset List PTY List 15 2 Touch “Band.” 12:00 ATT Source List Top The band list appears. FM1 FM2 FM3 Band AM1 Receive Menu AM2 Preset List PTY List 15 3 12:00 Touch the desired band (“FM1,” “FM2,” “FM3,” “AM1” or “AM2”). Touch “Band” to close the band list. 4 Perform tuning.
Reception controls Touch the display if the reception controls are not shown. 1 Source List 2 3 ATT Top Band Receive Menu Preset List 15 PTY List 12:00 4 56 7 8 9 No. Item Touch to 1 “Source List” open the source list. (page 11) 2 “ATT” attenuate the sound. To cancel, touch again. 3 “Top” open the source list. (page 11) 4 m/M tune manually. Touch and hold to skip frequencies continuously. 5 ./> tune automatically. 6 “Band” open the band list and change the band.
Playing discs Depending on the disc, some operations may be different or restricted. Refer to the operating instructions supplied with your disc. 1 Insert the disc (label side up). Playback starts automatically. If the DVD menu appears Touch the item in the DVD menu directly. You can also use the menu control panel which can be shown by touching the display in a place other than menu item area. Touch b/v/V/B to move the cursor, then “Enter” to confirm.
Playback controls Touch the display if the playback controls are not shown. Common to all discs/formats 1 Source List 2 3 ATT Top DVD Control 15 4 Source List ATT Top Play Menu SHUF DVD Control 12:00 15 12:00 7 6 5 Play Menu SHUF MPEG-4 Source List ATT Top PBC Panel Source List ATT Top Play Menu SHUF List Play Menu SHUF Album 15 12:00 8 9 Source List 15 12:00 9 0 ATT Top ZAP List Play Menu SHUF Album 15 12:00 qa 18 No.
No. Item Touch to 4 skip a chapter/track/scene/image/file. ./> Touch and hold momentarily to reverse/fast-forward the video; and then repeatedly to switch the speed (× 2 t × 12 t × 120 t × 2…)*1. To cancel, touch u. Touch and hold to reverse/fast-forward the audio track. During pause, touch and hold down > to play the video in slow motion. To cancel, release the key. 5 u pause/resume play after pause. 6 “Play Menu” open the play menu, which contains the following.
Indications during playback Touch the display to show the indications. For audio discs, some indications are always shown during playback.
Advanced Operations — Radio Storing and receiving stations Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. Storing automatically — BTM 1 2 Touch “Source List,” then “Tuner.” To change the band, touch “Band,” then select the desired band (“FM1,” “FM2,” “FM3,” “AM1” or “AM2”). RDS Overview FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio program signal.
Selecting PTY 1 During FM reception, touch “PTY List.” The PTY list appears if the station is transmitting PTY data. To scroll the list, touch v/V. 2 Touch the desired program type. The unit searches for a station broadcasting the selected program type. To close the PTY list, touch “PTY List.” Using PBC functions — Playback control The PBC menu interactively assists with operations while a PBC compatible VCD is played. 1 Start playing a PBC compatible VCD. The PBC menu appears.
Configuring audio settings Changing the audio channel Note Discs in DTS format are not supported. The sound is not output if the DTS format is selected. Changing the audio language/ format The audio language can be changed if the disc is recorded with multilingual tracks. You can also change the audio format when playing a disc recorded in multiple audio formats (e.g., Dolby Digital).
Locking discs — Parental control * * Excluding DVD-R/DVD-R DL/DVD-RW in VR mode. You can lock a disc, or set playback restrictions according to a predetermined level such as viewer age. Restricted scenes can be blocked or replaced with different scenes when a parental control compatible DVD is played. Changing the area and its movie rating level The restriction levels can be set depending on the area and its movie ratings. 1 While the unit is off, touch “Source List,” then . 2 Touch “Visual.
The repeat options and switching order of each disc/format are indicated below. Disc/format Options “OFF”: Returns to normal play mode. “Title”: Repeats the current title. “Chapter”: Repeats the current chapter. *1 “OFF”: Returns to normal play mode. “Track”: Repeats the current track. “OFF”: Returns to normal play mode. “Track”: Repeats the current track. “Album”: Repeats the current album (folder). “OFF”: Returns to normal play mode. “Image”: Repeats the current image.
USB Device Operations For details on the compatibility of your USB device, visit the support site. Support site http://esupport.sony.com http://www.sony.com/mobileAV • MSC (Mass Storage Class) and MTP (Media Transfer Protocol) type USB devices compliant with the USB standard can be used. • Corresponding codec is MP3 (.mp3), WMA (.wma), AAC (.m4a), JPEG (.jpg) and MPEG-4 (.mp4). • Backup of data in a USB device is recommended. Notes • Connect the USB device after starting the engine.
Enjoying music according to your mood — SensMe™ Sony’s unique “SensMe™ channels” and “SensMe™ mood” features automatically group tracks by channel or mood, and allow you to enjoy music intuitively. Before using the SensMe™ function 3 Transferring tracks to the USB device using “Content Transfer” In order to group tracks by channel or mood, track sound patterns need to be analyzed by 12 TONE ANALYSIS, which is loaded in “Content Transfer.
Registering a USB device using “SensMe™ Setup” Playing tracks in the channel — SensMe™ channels USB device registration is required to enable the SensMe™ function on the unit. “SensMe™ channels” automatically group tracks into channels by their tunes. You can select and play a channel that fits your mood, activity, etc. If registration is not performed along with the installation procedure, follow the steps below. 1 Start “SensMe™ Setup” on your computer. 2 Connect a USB device to your computer.
Channel list x Recommended, Shuffle All “Morning” (5:00 AM – 9:59 AM) “Daytime” (10:00 AM – 3:59 PM) “Evening” (4:00 PM – 6:59 PM) “Night” (7:00 PM – 11:59 PM) “Midnight” (12:00 AM – 4:59 AM) Tracks recommended for each time of day. Set the clock (page 46) for the channel to be displayed accurately. “Shuffle All”: Plays all analyzed tracks in random order. x Basic channels Plays tracks according to the music type. “Energetic”: High-spirit tracks. “Relax”: Calm tracks.
Playing tracks in the mood map — SensMe™ mood “SensMe™ mood” distributes tracks as dots on a two-axis mood map, based on the characteristics of the individual tracks. Controls and indications during “SensMe™ mood” playback A B C D E Fast By touching the point on the map according to your mood, a circle appears around the touched point, and the tracks inside the circle are played. Mood 1 Style 2 3 Connect a USB device set up for the SensMe™ function. Time Touch “Source List,” then “SensMe™.
iPod Operations For details on the compatibility of your iPod, see “About iPod” on page 50 or visit the support site. Support site http://esupport.sony.com http://www.sony.com/mobileAV In this manual, “iPod” is used as a general reference for the iPod functions on the iPod and iPhone, unless otherwise specified by the text or illustrations. Playing an iPod 1 2 Reduce the volume on this unit. Remove the cap from the USB connector, and connect the iPod to the USB connector.
Repeat and shuffle play 1 During playback, touch “Play Menu,” then the “Repeat” or “Shuffle” box repeatedly until the desired option appears. Repeat or shuffle play starts. To close the play menu, touch “Play Menu.” The repeat options are as follows. For audio playback “OFF”: Returns to normal play mode. “Track”: Repeats the current track. “Album”/“Podcast”/“Artist”/“Playlist”/ “Genre”*: Repeats the current item of the selected play mode. For video playback “OFF”: Returns to normal play mode.
Useful Functions Listing up tracks/images/video files — List Selecting a track/image/video file MPEG-4 You can list up albums/folders/tracks/images/ video files, and select a desired one to play. This function is convenient especially for the disc in MP3/WMA/AAC/JPEG/MPEG-4 format or USB device containing many albums/tracks, etc. 1 While playing back short track passages in a disc or USB device in sequence, you can search for a track you want to listen to.
Using Gesture Command You can perform frequently-used operations by drawing the following command stroke in the reception/playback display. Draw To Radio reception: seek forward stations. (The same as >.) Sound Adjustment Selecting the sound quality — EQ7 You can select an equalizer curve from 7 music types (“Xplod,” “Vocal,” “Edge,” “Cruise,” “Space,” “Gravity,” “Custom” or “OFF”). 1 During reception/playback, touch “Source List,” then . 2 Touch “Sound.” The sound setting menu appears.
Tip Other equalizer types are also adjustable. Optimizing sound for the listening position — Intelligent Time Alignment Adjusting the sound characteristics The sound balance between left and right speakers (“Balance”) and front and rear speakers (“Fader”) can be adjusted to your preference. You can also adjust the volume level of subwoofer if it is connected. 1 During reception/playback, touch “Source List,” then . 2 Touch “Sound.” The sound setting menu appears. 3 Touch “Balance/Fader.
Precisely calibrating the listening position — Intelligent Time Alignment Tune Speaker configuration and volume setup You can precisely calibrate your listening position from each speaker so that the sound delay reaches the listener more correctly. Creating a virtual center speaker — CSO Before starting, measure the distance between your listening position and each speaker. To fully enjoy surround sound, it is adequate to have 5 speakers (front left/right, rear left/right, center) and 1 subwoofer.
Adjusting the speaker volume Monitor Adjustment You can adjust the volume level of each connected speaker. The adjustable speakers are “Front R” (Front Right), “Front L” (Front Left), “Surround L” (Rear Left), “Surround R” (Rear Right) and “Subwoofer*.” Touch panel calibration * Adjustable only when a subwoofer is connected and “Subwoofer” is set to “ON” (page 42). 1 While the unit is off, touch “Source List,” then . 2 Touch “Sound.” The sound setting menu appears. 3 Touch v/V to scroll, then “4.
Selecting the picture quality — Picture EQ You can select a picture quality suitable for the interior brightness of the car. The options are indicated below. “Dynamic”: Vivid picture with bright, clear colors. “Standard”: Standard picture quality. “Theater”: Brightens the monitor; suitable for darkly-lit movies. “Sepia”: Applies a sepia tone to the picture. “Custom 1,” “Custom 2”: User-adjustable settings (page 38). 1 During video/image playback, touch “Source List,” then . 2 Touch “Screen.
Settings The setting menu includes the following categories. • • • • “General”: General settings (page 40) “Sound”: Sound settings (page 42) “Screen”: Screen settings (page 43) “Visual”: DVD and other playback settings (page 44) Basic setting operation You can set items in the menu by the following procedure. E.g., when setting the demonstration 1 While the unit is off, touch “Source List,” then . The setting menu appears.
General settings Touch c “General” c the desired item c the desired option. For details on this procedure, see “Basic setting operation” on page 39. Follow the page reference for details. “z” indicates the default setting. Item Option Purpose Unit status Security Control (page 46) – – Any status. Clock Adjust (page 46) – – Any status. No (z) Auto OFF Shuts off automatically after a desired time when the unit is 30sec, 30min, off. To deactivate the Auto Off function.
Item Option Purpose Default (z) Rotary Commander Changes the operative direction of rotary commander Reverse controls. To use in the factory-set position. AUX1 Input (page 46) Sets the type of device connected to the AUX1 IN terminals to switch the background screen accordingly. Video (z) To show the picture from the connected device. Audio To show this unit’s background screen. OFF To deactivate the AUX input.
Sound settings Touch c “Sound” c the desired item c the desired option. For details on this procedure, see “Basic setting operation” on page 39. Follow the page reference for details. “z” indicates the default setting. Item EQ7 (page 34) Option Purpose OFF (z) To cancel the equalizer curve. Xplod, Vocal, To select the equalizer Edge, Cruise, curve; customize the Space, Gravity, equalizer curve. Custom Balance/Fader (page 35) Balance: (L15 ~ R15) Fader: (F15 ~ R15) z: 0 To adjust the level.
Item Option Purpose RBE (Rear Bass Enhancer) (page 36) Uses rear speakers as a subwoofer. OFF (z), RBE1, RBE2, RBE3 To select the mode. Crossover Filter Selects the cut-off frequency of the front/rear speakers (HPF) and subwoofer (LPF). LPF: 50 Hz, 60 Hz, 80 Hz, 100 Hz (z), 120 Hz To select the cut-off frequency. (Available only when “Subwoofer” is set to “ON.”) HPF: OFF (z) To not cut out the frequency. During reception/ playback. HPF: 50 Hz, To select the cut-off 60 Hz, 80 Hz, frequency.
DVD and other playback settings Touch c “Visual” c the desired item c the desired option. For details on this procedure, see “Basic setting operation” on page 39. Follow the page reference for details. “z” indicates the default setting. Item Option Purpose Unit status DVD Menu Language – To change the disc’s menu language. Unit off. DVD Audio Language – To change the soundtrack language. Unit off. DVD Subtitle Language – To change the subtitle language recorded on the disc. Unit off.
Item Option 16:9 (z) Monitor Type Selects an aspect ratio suitable for the connected monitor. (The screen aspect ratio of this unit also changes.) Depending on the disc, “4:3 Letter Box” may be selected automatically instead of “4:3 Pan Scan,” and vice versa. 4:3 Letter Box Purpose To display the wide picture. Suitable when connecting to a wide-screen monitor or a monitor with a wide mode function. To display a wide picture with bands on the upper and lower positions of the screen.
Setting the security code Using Optional Equipment This unit has a security function to discourage theft. Enter a 4-digit number as your security code. Once the security function is activated, you need to enter the security code to turn on the unit after re-installing the unit in another car or charging the battery. You can connect up to 2 optional devices, such as portable media player, game, etc., to the AUX1 IN and AUX2 IN terminals on the unit.
Setting the type of device By setting the type (video or audio) of each connected device, the background screen can be switched accordingly. 1 While the unit is off, touch “Source List,” then . The general setting menu appears. If not, touch “General.” 2 Touch v/V to scroll, then “AUX1 Input” or “AUX2 Input.” 3 Touch “Audio” or “Video.” The setting is complete. To deactivate the AUX input, select “OFF.” To return to the previous display, touch “Back.
Additional Information Precautions • Cool off the unit beforehand if your car has been parked in direct sunlight. • Power antenna (aerial) extends automatically. Moisture condensation Should moisture condensation occur inside the unit, remove the disc and wait for about an hour for it to dry out; otherwise the unit will not operate properly. To maintain high sound quality Do not splash liquid onto the unit or discs.
Notes on finalizing discs The following discs are required to be finalized to play on this unit. • DVD-R/DVD-R DL (in video mode/VR mode) • DVD-RW in video mode • DVD+R/DVD+R DL • CD-R • CD-RW The following discs can be played without finalization. • DVD+RW – automatically finalized. • DVD-RW in VR mode – finalization not required. For details, see the manual supplied with the disc.
About MPEG-4 files MPEG-4 files meeting the following requirements can be played. Playback is not be guaranteed for all MPEG-4 files meeting the requirements. • Profile: MPEG-4 Simple profile • Bit rate: Max. 7 Mbps on USB FS, 10 Mbps on DVD, 7 Mbps on CD • Frame rate: Max. 30 fps • Image size: Max. 720 × 480 pixels • Audio: Max. 320 kbps (AAC-LC) • File extension: .
Specifications FOR UNITED STATES CUSTOMERS. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC. POUR LES CONSOMMATEURS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA PROVINCE DE QUÉBEC. AUDIO POWER SPECIFICATIONS CEA2006 Standard Power Output: 17 Watts RMS 4 at 4 Ohms < 1% THD+N SN Ratio: 82 dBA (reference: 1 Watt into 4 Ohms) Monitor section Display type: Wide LCD color monitor Dimensions: 6.
• Halogenated flame retardants are not used in the certain printed wiring boards. • Halogenated flame retardants are not used in cabinets. • Packaging cushions are made from paper. Region code The region system is used to protect software copyrights. The region code is located on the bottom of the unit, and only DVDs labeled with an identical region code can be played on this unit. DVDs labeled ALL can also be played. If you try to play any other DVD, the message “Playback prohibited by region code.
Card remote commander operation is not possible. If the Monitor Off function is activated (no lighting), card remote commander operation is not possible (page 11). The menu items cannot be selected. Unavailable menu items are shown in grey. AUX cannot be selected as the source. All AUX input settings are set to “OFF.” t Set “AUX1 Input”/“AUX2 Input” to “Video” or “Audio” (page 47). Radio reception The stations cannot be received. The sound is hampered by noises. • The connection is not correct.
Disc operation The disc cannot be loaded. • Another disc is already loaded. • The disc has been forcibly inserted upside down or in the wrong way. The disc does not play back. • Defective or dirty disc. • The disc is not applicable. • The DVD is not applicable due to the region code. • The disc is not finalized (page 49). • The disc format and file version are incompatible with this unit (page 9, 48). • Press Z to remove the disc. MP3/WMA/AAC/JPEG/MPEG-4 files do not play back.
Error displays/messages Cannot read. • The unit cannot read the data due to some problem. • The data is damaged or corrupted. Cannot read disc. Disc may be corrupted. • The disc is corrupted. • The disc is incompatible with this unit. • The disc is not finalized. Disc Error • The disc is dirty or inserted upside down. t Clean or insert the disc correctly. • A blank disc has been inserted. • The disc cannot play due to a problem. t Insert another disc. • The disc is not compatible with this unit.
Language code/area code list Language code list The language spellings conform to the ISO 639: 1988 (E/F) standard.
Index A D H AAC 9, 49 Angle (Angle) 19 Area code 56 Audio channel (Stereo) 23 Audio DRC (Audio DRC) 44 Audio format (Audio) 23 Auto Off (Auto OFF) 40 Auxiliary equipment 46 Auxiliary level (Level) 46 Auxiliary settings (AUX1 Input, AUX2 Input) 41, 47 Demonstration (Demo) 43 Dimmer level (Dimmer Level) 40 Dimmer setting (Dimmer) 40 Discs 9 Display language (Language) 14, 40 Dolby D level (Dolby D Level) 23 Dolby Digital 23 DVD audio language (Audio, DVD Audio Language) 23, 44 DVD control menu (DVD Contro
P S PAL 40 Parental control settings (DVD Parental Control) 24, 44 Passenger control (Passenger Control) 32 Picture EQ 38, 43 Play menu (Play Menu) 19 Playable discs 9 Playback control (Video CD PBC) 22, 45 Playback settings (Visual) 44 Program Types (PTY) 21, 22 Screen aspect ratio (Aspect) 38, 43 Screen settings (Screen) 43 Security function (Security Control) 46 SensMe™ 27 Shuffle play (Shuffle) 24, 26, 32 Slide show interval (JPEG Slide Show) 45 Slow-motion play 19 Sound settings (Sound) 42 Speaker v
If you have any questions/problems regarding this product, try the following: 1 Read Troubleshooting in these Operating Instructions. 2 Reset the unit. Note: Stored data may be erased. 3 Please contact (U.S.A. only); Call 1-800-222-7669 URL http://www.SONY.com http://www.sony.
!6 #ENTER )NSTALLATION #ONNECTIONS )NSTALLATION 2ACCORDEMENT )NSTALACIØN #ONEXIONES 8!6
ʓ ʔ ʕ ʖ § %QUIPMENT USED IN ILLUSTRATIONS NOT SUPPLIED !PPAREILS UTILISÏS DANS LES ILLUSTRATIONS NON FOURNIS %QUIPO UTILIZADO EN LAS ILUSTRACIONES NO SUMINISTRADO &RONT SPEAKER (AUT PARLEUR AVANT !LTAVOZ FRONTAL 2EAR SPEAKER (AUT PARLEUR ARRIÒRE !LTAVOZ POSTERIOR 53" DEVICE 0ÏRIPHÏRIQUE 53" $ISPOSITIVO 53" I0OD 0OWER AMPLIFIER !MPLIFICATEUR DE PUISSANCE !MPLIFICADOR DE POTENCIA !CTIVE SUBWOOFER #AISSON DE GRAVES ACTIF !LTAVOZ POTENCIADOR DE GRAVES ACTIVO #$ CHANGER #HANGEUR #$ #AMBIADOR DE #$
0RÏCAUTIONS ! s #ET APPAREIL EST EXCLUSIVEMENT CONÎU POUR FONCTIONNER SUR UNE TENSION DE 6 ## AVEC MASSE NÏGATIVE s .E DÏMONTEZ PAS OU NE MODIFIEZ PAS L APPAREIL s .
"LACK .OIR .EGRO /RANGE WHITE STRIPED 2AYÏ ORANGE BLANC #ON RAYAS NARANJAS Y BLANCAS 2ED 2OUGE 2OJO "LUE "LEU !ZUL !.4 2%-AX SUPPLY CURRENT ! #OURANT MAX FOURNI ! #ORRIENTE MÈX DE ALIMENTACIØN DE ! !-0 2%- ),,5-).!4)/. "LUE WHITE STRIPED 2AYÏ BLEU BLANC #ON RAYAS AZULES Y BLANCAS 9ELLOW *AUNE !MARILLO -AX SUPPLY CURRENT ! #OURANT MAX FOURNI ! #ORRIENTE MÈX DE ALIMENTACIØN DE ! ,IGHT BLUE "LEU CIEL !ZUL CLARO !44 ,IGHT GREEN 6ERT CLAIR 6ERDE CLARO 0!2+).
! " TO DASHBOARD CENTER CONSOLE VERS LE TABLEAU DE BORD LA CONSOLE CENTRALE AL TABLERO O CONSOLA CENTRAL &OOT BRAKE TYPE 4YPE FREIN Ë PIED 4IPO DE FRENO DE PEDAL 0ARKING BRAKE SWITCH CORD #ORDON DU CAPTEUR DU FREIN Ë MAIN #ABLE DE CONMUTACIØN DEL FRENO DE ESTACIONAMIENTO (AND BRAKE TYPE 4YPE FREIN Ë MAIN 4IPO DE FRENO MANUAL SIZE ʖ § MAX MM § MAX IN DIMENSION § MAX MM § PO MAX TAMA×O § MM MÈX ʖ ,ARGER THAN MM IN ,ARGEUR MINIMALE DE MM PO 3UP
0RECAUTIONS s #HOOSE THE INSTALLATION LOCATION CAREFULLY SO THAT THE UNIT WILL NOT INTERFERE WITH NORMAL DRIVING OPERATIONS s !VOID INSTALLING THE UNIT IN AREAS SUBJECT TO DUST DIRT EXCESSIVE VIBRATION OR HIGH TEMPERATURES SUCH AS IN DIRECT SUNLIGHT OR NEAR HEATER DUCTS s 5SE ONLY THE SUPPLIED MOUNTING HARDWARE FOR A SAFE AND SECURE INSTALLATION Ǹ " -OUNTING THE UNIT IN A *APANESE CAR 9OU MAY BE ABLE TO INSTALL THIS UNIT IN SOME MAKES OF *APANESE CARS WITHOUT AN INSTALLATION KIT NOT SUPPLIED )N THE C
0RÏCAUTIONS s #HOISISSEZ SOIGNEUSEMENT L EMPLACEMENT D INSTALLATION POUR QUE L APPAREIL NE GÐNE PAS LE CHAUFFEUR PENDANT LA CONDUITE s ²VITEZ D INSTALLER L APPAREIL DANS UN ENDROIT EXPOSÏ Ë LA POUSSIÒRE Ë LA SALETÏ Ë DES VIBRATIONS EXCESSIVES OU Ë DES TEMPÏRATURES ÏLEVÏES COMME EN PLEIN SOLEIL OU Ë PROXIMITÏ DE CONDUITS DE CHAUFFAGE s 0OUR GARANTIR UN MONTAGE SßR N UTILISEZ QUE LE MATÏRIEL FOURNI Ǹ " -ONTAGE DE L APPAREIL DANS UNE VOITURE JAPONAISE )L PEUT ÐTRE POSSIBLE D INSTALLER CET APPAREIL DANS CER
3-272-643-01 ® Car Audio LIMITED WARRANTY (U.S. Only) Sony Electronics Inc. (“Sony”) warrants this product against defects in material or workmanship for the time periods and as set forth below. Pursuant to this Limited Warranty, Sony will, at its option, (i) repair the product using new or refurbished parts or (ii) replace the product with a new or refurbished product. For purposes of this Limited Warranty, “refurbished” means a product or part that has been returned to its original specifications.