3-246-852-12 (1) FM/AM Cassette Car Stereo Operating Instructions US Mode d’emploi FR Owner’s Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XR-CA350X Serial No. For installation and connections, see the supplied installation/connections manual.
Warning Welcome ! This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Precautions Notes on Cassettes •If your car was parked in direct sunlight resulting in a considerable rise in temperature inside the car, allow the unit to cool off before operating it. •If no power is being supplied to the unit, check the connections first. If everything is in order, check the fuse. •If no sound comes from the speakers of a 2-speaker system, set the fader control to the center position.
Table of Contents With Optional Equipment This Unit Only Location of controls ................................................. 5 Getting Started Resetting the unit ................................................ 6 Detaching the front panel .................................. 6 Setting the clock .................................................. 7 CD/MD Unit Playing a CD or MD ......................................... 12 Playing tracks repeatedly — Repeat Play ............................................
Location of controls DIR SOURCE EQ3 SEEK MODE DSPL DISC RELEASE SEL ATT 1 REP SHUF 3 4 2 ATA 5 6 SENS BTM OFF XR-CA350X Refer to the pages listed for details.
Attaching the front panel Getting Started Attach part A of the front panel to part B of the unit as illustrated and push the left side into position until it clicks. Resetting the unit Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Remove the front panel and press the RESET button with a pointed object, such as a ballpoint pen.
Setting the clock The clock uses a 12-hour digital indication. Cassette Player Example: To set the clock to 10:08 1 Press (DSPL) for 2 seconds. The hour indication flashes. Listening to a tape Insert a cassette. Playback starts automatically. 1 Press either side of the volume button to set the hour. to go forward The side facing up is played. to go back The side facing down is played. 2 Press (SEL). Tip To change the tape‘s playback direction, press m and M. The minute indication flashes.
Radio reception during fast-forwarding or rewinding of a tape — Automatic Tuner Activation (ATA) When fast-forwarding or rewinding with the m or M button, the radio will turn on automatically. During playback, press (BTM) (ATA) repeatedly until “ATA-ON” in the display appears. ATA-ON y ATA-OFF ATA mode starts. To return to normal play mode, select “ATAOFF.
Storing only the desired stations You can preset up to 18 FM stations (6 each for FM1, 2, and 3) and up to 12 AM stations (6 each for AM1 and 2) in the order of your choice. 1 Press (SOURCE) repeatedly to select the radio. In case of tape playback, press Z to eject the tape. If you cannot tune in a preset station — Automatic tuning/ Local Seek Mode Automatic tuning: Press either side of (SEEK) to search for the station. Scanning stops when the unit receives a station.
Other Functions Changing the sound and display settings You can adjust the balance and fader. The following items can be set: •A.SCRL (Auto Scroll)* (page 12). •M.DSPL (Motion Display) – the demonstration mode which appears when the tape is ejected and no source is selected (e.g., tuner is turned off). •BEEP – to turn the beep sound on or off. 1 1 Adjusting the balance and fader Press (SEL) repeatedly until “BAL” or “FAD” appears.
Setting the equalizer — EQ3 You can select an equalizer curve for 7 music types (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM, and OFF (equalizer OFF)). You can store a different equalizer setting for each source. Selecting the equalizer curve 1 Press (SOURCE) to select a source (Radio, CD or MD) or insert a cassette. 2 Press (EQ3) repeatedly to select the desired equalizer curve. Each time you press (EQ3), the item changes.
With Optional Equipment CD/MD Unit This unit can control external CD/MD units. If you connect an optional CD unit with the CD TEXT function, the CD TEXT information will appear in the display when you play a CD TEXT disc. Playing a CD or MD 1 2 Press (SOURCE) repeatedly to select CD or MD. In case of tape playback, press Z to eject the tape. Press (MODE) until the desired unit appears. CD/MD playback starts. When a CD/MD unit is connected, all the tracks play from the beginning.
Locating a specific track — Automatic Music Sensor (AMS) During playback, press either side of (SEEK) momentarily for each track you want to skip. Playing tracks repeatedly — Repeat Play You can select: •REP-TRACK – to repeat a track. •REP-DISC – to repeat a disc. To locate succeeding tracks SEEK To locate preceding tracks Locating a specific point in a track — Manual Search During playback, press and hold either side of (SEEK). Release when you have found the desired point.
Additional Information Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, open the front panel by pressing (RELEASE), then detach it and clean the connectors with a cotton swab dipped in alcohol. Do not apply too much force. Otherwise, the connectors may be damaged. Maintenance Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse.
Removing the unit 1 Remove the protection collar. 1 Detach the front panel (page 6). 2 Engage the release keys together with the protection collar. Orient the release key correctly. 3 Pull out the release keys to remove the protection collar. 2 Remove the unit. 1 Insert both release keys together until they click. Face the hook inwards. 2 Pull the release keys to unseat the unit. 3 Slide the unit out of the mounting.
Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 22 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5 % total harmonic distortion. Other specifications Cassette player section Tape track Wow and flutter Frequency response Signal-to-noise ratio 4-track 2-channel stereo 0.13 % (WRMS) 30 – 15,000 Hz 55 dB General Outputs Inputs Tuner section Tone controls FM Tuning range FM tuning interval: 87.
Troubleshooting guide The following checklist will help you remedy the problems you may encounter with your unit. Before going through the checklist below, check the connections and operating procedures. General Problem Cause/Solution No sound. •Cancel the ATT function (page 10). •Set the fader control to the center position for 2-speaker systems. •Adjust the volume with (+). The contents of the memory have been erased. • The power cord or battery has been disconnected. • The RESET button was pressed.
Error displays (when an optional CD/MD unit is connected) The following indications will flash for about 5 seconds, and an alarm sound will be heard. Display NO MAG NO DISC Cause Solution The disc magazine is not inserted in the CD/MD unit. Insert the disc magazine in the CD/ MD unit. No disc is inserted in the CD/MD unit. Insert discs in the CD/MD unit. A CD is dirty or inserted upside down.*2 Clean or insert the CD correctly. *1 An MD does not play because of some Insert another MD. problem.
Félicitations ! Précautions Nous vous remercions pour l’achat de ce lecteur de cassette Sony. •Si votre voiture est garée en plein soleil et si la température à l’intérieur de l’habitacle a considérablement augmenté, laissez refroidir l’appareil avant de l’utiliser. •Si l’appareil n’est pas alimenté, vérifiez d’abord les connexions. Si tout est en ordre, vérifiez le fusible.
Remarques à propos des cassettes Entretien des cassettes • Ne touchez pas la bande magnétique d’une cassette parce que la poussière et les souillures entraînent un encrassement des têtes. • Gardez les cassettes à l’écart des appareils intégrant des aimants, tels que des hautparleurs et des amplificateurs qui risquent de provoquer une distorsion ou un effacement des cassettes enregistrées. • N’exposez pas les cassettes au rayonnement direct du soleil, aux températures extrêmement froides ou à l’humidité.
Table des matières Description de cet appareil Emplacement des commandes .............................. 5 Préparation Réinitialisation de l’appareil .............................. 6 Dépose de la façade ............................................ 6 Réglage de l’horloge ........................................... 7 Avec appareils optionnels Appareil CD/MD Lecture d’un CD ou d’un MD ......................... 12 Lecture de plages répétée — Lecture répétée ........................................
Emplacement des commandes DIR SOURCE EQ3 SEEK MODE DSPL DISC RELEASE SEL ATT 1 REP 2 3 SHUF 4 ATA 5 6 SENS BTM OFF XR-CA350X Pour plus de détails, reportez-vous aux pages indiquées.
Fixation de la façade Fixez la partie A de la façade à la partie B de l’appareil comme illustré et poussez le côté gauche en position jusqu’au déclic. Préparation Réinitialisation de l’appareil Avant la première mise en service de l’appareil, ou après avoir remplacé la batterie du véhicule ou modifié les raccordements, vous devez réinitialiser l’appareil. Retirez la façade et appuyez sur la touche RESET à l’aide d’un objet pointu comme un stylo à bille.
Réglage de l’horloge L’horloge à affichage numérique fonctionne suivant un cycle de 12 heures. Exemple : Pour régler l’horloge à 10:08 1 Appuyez sur (DSPL) pendant 2 secondes. Lecteur de cassettes Lecture d’une cassette Introduisez une cassette. La lecture démarre automatiquement. L’indication des heures se met à clignoter. 1 Appuyez sur l’un des côtés de la touche volume pour régler l’heure. pour avancer La face supérieure est reproduite. pour reculer La face inférieure est reproduite.
Réception radio en cours d’avance rapide ou de rembobinage d’une cassette — Activation automatique du syntoniseur (ATA) La radio s’allume automatiquement lorsque les touches m ou M sont utilisées pour l’avance ou le retour rapide. En cours de lecture, appuyez plusieurs fois sur (BTM) (ATA) jusqu’à ce que l’indication “ATA-ON” apparaisse dans la fenêtre d’affichage.
Mémorisation des stations souhaitées uniquement Vous pouvez présélectionner jusqu’à 18 stations FM (6 en FM1, 2 et 3), 12 stations AM (6 en AM1 et 2), dans l’ordre de votre choix. 1 Appuyez plusieurs fois sur (SOURCE) pour sélectionner la radio. Si une cassette est en cours de lecture, pressez Z pour l’éjecter. 2 Appuyez plusieurs fois sur (MODE) pour sélectionner la bande de fréquence.
Autres fonctions Réglage de la balance gauche-droite et de l’équilibre avant-arrière Vous pouvez régler la balance gauche-droite et l’équilibre avant-arrière. 1 Modification des réglages du son et de l’affichage Les paramètres suivants peuvent être réglés : •A.SCRL (défilement automatique)* (page 12). •M.DSPL (affichage animé) – Le mode démonstration apparaît lorsque la cassette est éjectée et qu’aucune source n’est sélectionnée (par exemple, le récepteur est éteint).
Réglage de l’égaliseur — EQ3 Vous pouvez sélectionner une courbe d’égaliseur pour 7 types de musique (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM, et OFF (égaliseur réglé sur OFF)). Vous pouvez sauvegarder un réglage d’égaliseur différent pour chaque source. Sélection de la courbe d’égaliseur 1 Appuyez sur (SOURCE) pour sélectionner une source (Radio, CD ou MD) ou insérez une cassette. 2 Appuyez plusieurs fois sur (EQ3) pour sélectionner la courbe d’égaliseur souhaitée.
Avec appareils optionnels Appareil CD/MD Cet appareil peut commander des appareils CD et MD externes. Si vous raccordez un appareil CD en option dotée de la fonction CD TEXT, les informations CD TEXT apparaissent dans la fenêtre d’affichage pendant la lecture des disques CD TEXT. Lecture d’un CD ou d’un MD 1 2 Appuyez plusieurs fois sur (SOURCE) pour sélectionner le CD ou le MD. Si une cassette est en cours de lecture, pressez Z pour l’éjecter.
Recherche d’une plage déterminée — Détecteur automatique de musique (AMS) En cours de lecture, appuyez brièvement sur l’un des côtés de (SEEK) pour chaque plage que vous souhaitez sauter. Pour rechercher parmi les plages suivantes SEEK Pour rechercher parmi les plages précédentes Recherche d’un passage déterminé sur une plage — Recherche manuelle En cours de lecture, appuyez et maintenez enfoncé n’importe quel côté de (SEEK). Relâchez-le lorsque vous avez trouvé le passage souhaité.
Informations supplémentaires Entretien Nettoyage des connecteurs Si les connecteurs situés entre l’appareil et la façade ne sont pas propres, le système peut ne pas bien fonctionner. Pour éviter cela, ouvrez la façade en appuyant sur (RELEASE), déposez-la ensuite et nettoyez-la à l’aide d’un coton-tige imprégné d’alcool. N’exercez pas une pression trop importante. Vous risqueriez sinon d’endommager le connecteur.
Démontage de l’appareil 1 Retirez le cadre de sûreté. 1 Retirez la façade (page 6). 2 Insérez les clés de déblocage simultanément dans le cadre de sûreté. Orientez correctement la clé de déblocage. 3 Tirez sur les clés de déblocage pour retirer le cadre de sûreté. 2 Retirez l’appareil. 1 Insérez les deux clés de déblocage simultanément jusqu’au déclic. Tournez le crochet vers l’intérieur. 2 Tirez sur les clés de déblocage pour extraire l’appareil. 3 Faites glisser l’appareil en dehors de son support.
Spécifications Lecteur de cassette Pistes sonores Pleurage et scintillement Réponse en fréquence Rapport signal/bruit 4 pistes 2 canaux stéréo 0,13 % (WRMS) 30 – 15.
Dépannage La liste de contrôles suivante vous aidera à remédier aux problèmes que vous pourriez rencontrer avec cet appareil. Avant de parcourir la liste ci-dessous, vérifiez les connexions et les procédures d’utilisation. Généralités Problème Cause/Solution Pas de son. • Annulez la fonction ATT (page 10). • Pour un système à 2 haut-parleurs, réglez la commande d’équilibre avant-arrière sur la position médiane. • Réglez le volume à l’aide de la touche (+). Le contenu de la mémoire a été effacé.
Affichage des erreurs (lorsqu’une unité CD/MD en option est raccordée) Les indications suivantes clignotent pendant environ 5 secondes et une alarme retentit. Cause Solution NO MAG Le chargeur de disques n’est pas introduit dans l’appareil CD/MD. Introduisez le chargeur de disques dans l’appareil CD/MD. NO DISC Il n’y a aucun disque dans l’appareil CD/MD. Introduisez des disques dans l’appareil CD/MD. Un CD est souillé ou a été introduit à l’envers.*2 Nettoyez ou introduisez correctement le CD.