User Manual

ManualsBrandsSORIN CRM ManualsElectronicsImplantable pacemaker with RF com.

Table Of Contents

1. General description
2. Intended use and targeted population
- 2.1. Intended use
- 2.2. Indications and targeted population
3. Contraindications and adverse events
- 3.1. General considerations
- 3.2. Adverse events, risks and side effects
4. Warnings
- 4.1. Pacemaker dependent patients
- 4.2. Warnings to patients
- 4.3. Risks related to medical environment
- 4.4. Storage
- 4.5. Packaging
  - 4.5.1. Characteristics of the sterile package
  - 4.5.2. Characteristics of the non-sterile package
5. Clinical studies
- 5.1. Methods
- 5.2. Patients studied
- 5.3. Safety results
- 5.4. Effectiveness results
6. Patient selection and treatment
- 6.1. Specific patient populations
7. Patient counseling information
8. Declaration of conformity
9. Physician guidelines
- 9.1. Physician training
- 9.2. Directions for use
- 9.3. Maintaining device quality
- 9.4. Implantation and device programming
- 9.5. Lead evaluation and lead connection
- 9.6. Programming and pacemaker operation
- 9.7. Rate increases
- 9.8. Generator explant and disposal
10. Patient information
11. How supplied
- 11.1. Sterility
- 11.2. Warranty and replacement policy
12. Implant procedure
- 12.1. Necessary equipment
- 12.2. Packaging contents
- 12.3. Optional equipment
- 12.4. Opening the package
- 12.5. Preparing the pocket
- 12.6. Choosing the type of lead
- 12.7. Measurement of thresholds at implant
- 12.8. Lead connections
- 12.9. Implant considerations
13. Pacemaker interrogation and upgrade
14. Special modes
- 14.1. Nominal mode (Safety mode)
- 14.2. Standby mode
- 14.3. Magnet mode
- 14.4. Response in the presence of interference
15. Functions and parameters
- 15.1. Pacing modes
  - 15.1.1. MRI Mode
- 15.2. Rates
- 15.3. Pacing and Sensing parameters
- 15.4. Refractory periods
- 15.5. Rate response
- 15.6. Therapeutic improvements
- 15.7. Optimizing operation
- 15.8. Follow-up function
- 15.9. Remote monitoring function
16. Patient follow-up
- 16.1. Recommended Replacement Time (RRT)
- 16.2. Follow-up recommendations
- 16.3. Explantation
- 16.4. Programmer tests
- 16.5. Interrogating the diagnostic data (AIDA)
  - 16.5.1. SafeR (Preservation of AV conduction)
- 16.6. Pacemaker identification
17. Standby mode
18. Medical follow-up
- 18.1. Magnet test
  - 18.1.1. Magnet On
  - 18.1.2. Magnet Off
- 18.2. Capture test mode:
- 18.3. Rate test mode:
- 18.4. Threshold tests
  - 18.4.1. Ventricular threshold test
  - 18.4.2. Atrial threshold test
- 18.5. Lead measurements
- 18.6. Statistics
- 18.7. Markers and intracardiac ECG
  - 18.7.1. Markers
  - 18.7.2. Intracardiac ECG
- 18.8. Temporary programming
- 18.9. Memory functions
19. Physical characteristics
20. Electrical characteristics
- 20.1. Current drain at beginning of service
- 20.2. Correspondence between magnet rate and battery life
- 20.3. Battery
- 20.4. Longevity
- 20.5. Radio equipment emission
21. Programmable parameters
- 21.1. Antibradycardia pacing
- 21.2. Remote alerts and warnings
22. Non-programmable parameters
23. Warranty
- 23.1. Article 1: Terms of warranty
- 23.2. Article 2: Terms of replacement
24. Explanation of symbols

4. For the DR model, insert the atrial lead pin all the way into the appropriate port (marked

A) of the pacemaker and proceed as in steps 2 and 3.

CAUTION:

― Do not tighten the pre-inserted screw when there is no lead connector inserted (this could

damage the connector block).

― Do not loosen the screw before inserting the lead into the connector (subsequent risk of

being unable to reinsert the screw).

― Use only the screwdriver provided with the pacemaker. Maintain the screwdriver's shaft

perpendicular to the plane of the pacemaker (see figure below).

WARNING: Ensure that the screwdriver's tip is fully inserted in the setscrew; otherwise, the

screwdriver might damage the setscrew and prevent connection with or disconnection from

the lead.

To ensure full insertion, push the screwdriver's hex tip smoothly into the setscrew until it

reaches the bottom of the hex chamber in the screw, which can be felt as a solid metallic

contact. Do not implant the pacemaker if there is no feeling of solid metallic contact. Do

not implant the pacemaker if the screwdriver does not click when attempting to tighten the

setscrew on the lead pin.

IMPLANT CONSIDERATIONS

After placing the device in its pocket, check the pacemaker functioning using an ECG.

Suture the device to the muscle in order to avoid potential migration of the device into the

pectoral muscle.

12.9.

12. IMPLANT PROCEDURE

ALIZEA – UA10414A 33