Installation Guide

About the Privacy Lock
The Privacy Lock on the SOSS® UltraLatch® will secure your door from the inside
(Pull Side) of the room. Slide lever to the LEFT to activate.
Operating the Pull Side handle will disengage the Privacy Lock.
For instructions on how to configure the Privacy Lock on the push side of the
door, please see change over instructions insert or contact the factory.
A Trip Key is provided. To deactivate the Privacy Lock from outside of door, insert
Trip Key into small hole on the Unirose Cover. For LH Doors pull slightly toward
the hinge side of the door. For RH doors push key toward the door jamb.
For added security, use the SOSS® Single Cylinder Deadbolt by Medeco.
(See separate installation instructions).
For Bifold Closet Doors
Additional Tools needed:
1
/8" Drill bit
If installing UltraLatch® on bi-fold closet door,
please use the following procedure.
If other UltraLatch® handles are used in the
room, try to match height for consistency.
Please follow Door manufacturer's instructions
for location of the handles.
Determine the best distance from the door’s
edge to install the handle.
No 2
1
/8" hole is necessary. Once your placement
is determined, place Closet Unirose on face of
door, check for level, then mark for screw holes.
Pre-drill to
7
/8" depth with
1
/8" drill bit.
Attach Closet Unirose with the provided screws.
Attach rose cover and handle as directed in
step 10 and 11 of basic instructions.
Tip:
Mark top hole at 12 o'clock. Drill pilot hole and attach with screw to snug,
check for level. Mark other screw holes with pencil. Loosen Unirose and
rotate 180°. Drill other pilot holes. Return Unirose to original position and
install remaining screws.
Part #: LPUXAY2 © Copyright 2016, Universal Industrial Products, Inc.
SOSS
®
Door Hardware
Both handles must be installed before
activating the Privacy Lock.
Important Note
If Latch Disassembly from Door is Required.
Remove Pull Side handle, cover and Unirose by removing the three
screws. Depress spring clip while gently pulling on the Push Side
Unirose to free bolt to allow removal. While removing assembly,
depress clip from Pull Side, depress rack slightly to allow clearance for
the one inch hole.
Before attempting to reinstall, reset the Chassis Spring as shown on
the top of page 3.
Using Two UltraLatch® Drill Guides
Prepare
9
/32" drill bit by marking a stop mark with tape to allow 2”
maximum penetration for 1
3
/4" or 2" doors or 1
5
/8" for 1
3
/8" thick doors.
Measurement should be made from tip of drill bit to the tape marker.
Insert UltraLatch® Drill Guide into 2
1
/8" hole on the Push Side of the
door, insert screws to align for second Drill Guide on Pull Side of door.
Tighten screws slightly, check with torpedo level to ensure that Drill
Guides are level. If both sides are level, tighten screws and recheck for
level. Adjust if necessary. Drill first hole from the Push-Side of the door,
then go to the Pull-Side and drill until the holes meet.
May be covered by one or more U.S. Patent Nos. 7,950,703; D603,244:, D600,531; D592,486; D584,594 and D502,641. Other Patents Pending.
UltraLatch® is made in the U.S.A. of domestic and imported components.
Universal Industrial Products, Inc.
One Coreway Drive
Pioneer, OH, USA 43554-0628
Phone: [phone] [phone]
FAX: [phone]
Email: [e-mail] Internet: www.soss.com
4
Trip Key
12
Using 2 UltraLatch® Drill
Guides will save set-up time.
Tape Stop-Mark
UltraLatch
Drill Guide
UltraLatch
Drill Guide
Push Side