400B SERIES ELECTRIC DIAPHRAGM PUMPS Owner’s Operation Manual
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Table of Contents Limited Warranty Policy....................................................................... 3 Thank You! Basic Definitions................................................................................. 3 Thank you for your loyalty to the Sotera® brand of chemical, lubricant, and mixed hydrocarbon transfer pumps. Your safety is important, so please read and thoroughly understand the procedures set forth in this manual.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Limited Warranty Policy FROM DATE OF SALE PRODUCT SERIES Five (5) Years 400 Series pump only (all models) Motor and meters not included Two (2) Years 820, 825, and 850 meters One (1) Year All motors regardless of voltage class (explosion proof, non-explosion proof; 12V DC, 24V DC, and 115V AC) Accessories are defined as fittings, hoses, swivels,filters, strainers that are purchased within a 400B pump package or separately for use with a 400B
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL About This Manual From initial concept and design through final production, your Sotera product is built to provide years of trouble-free use. To ensure the safety of yourself and those around you, it is critical that this manual is read in its entirety prior to attempting to install or operate your new purchase.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL General Safety Information WARNING The 400B pump series is not intended to be used to fuel any aircraft, on or off road vehicle, or marine vessel. This pump is not suited for use with fluids for human consumption. Any electrical wiring should be performed ONLY by a licensed electrician in compliance with all local, state, and national electrical codes (NEC/ANISI/NFPA 30, 30A, and 70) as appropriate to the intended use of the pump.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Installation Best Practices (Discharge Side of Pump) • All discharge hoses should be a minimum of 1" diameter. Large sizes may be used as long as it terminates to a 1" diameter at the discharge outlet of the pump. • Hoses greater than 20' may be used, however, reduced outlet flow at the end of the hose or nozzle should be expected. Flow is dependent on the cP of the fluid as affected by temperature and elevation.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL AC Power DANGER All AC pumps will operate at the rated nameplate voltage. AC power should be supplied to the pump from a dedicated circuit with a 15 amp circuit protection. No other equipment should be powered by this circuit. Wiring must be of sufficient size to carry the correct current for the pump. Voltage drop will vary with distance to pump and size of wire.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Best Operational Practices Regular maintenance is critical to maintaining performance and extending the life of your 400B Series pump. • Always turn off the transfer pump and disconnect from a power source prior to servicing. • Always flush the pump completely prior to any service or disassembly. Sotera recommends the use of water for flushing agricultural and industrial chemicals.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Diaphragm Assembly Replacement Both the diaphragms and check valve assemblies can be serviced without removing the oil from the interior pump body cavity. It is important that only one (1) assembly be serviced at a time. Avoid any possible contamination of the oil within the internal pump cavity during this repair. Procedure 1.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Viscosity Correction Chart FLOW IN LITERS PER MINUTE (LPM) 7.6 15.1 22.7 30.3 37.9 45.4 53 60.6 15.2 45 13.7 40 12.2 35 10.7 30 9.1 25 7.6 20 6.1 15 4.6 10 3 5 1.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Anti-Drip Nozzle Spout Kit 400KTF0237 For use with Norwesco and other nozzles with a 1 3/16" outside diameter. Anti-Drip Nozzle Spout Installation 1. If there is a raised plastic notch on the nozzle, carefully remove it with a file before installing the anti-drip spout. Nozzle 2. Apply soapy water to the end to aid in the installation. Place the anti-drip spout on the nozzle as shown at right.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Troubleshooting Guide SYMPTOM Pump will not prime Pump hums but will not rotate Low pump capacity POSSIBLE CAUSE SOLUTION Suction line problem Check for leaks in suction line Leaky check valves Check for dirt or damaged check valves and replace Check valves improperly installed Check for proper installation Outlet plugged Check for blockage and clear Motor not operating Check power source Stripped or damaged gears Repair or replace
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL 9 17 19 18 3 1 2 4 21 27 28 5 6 24 7 23 8 9 16A 10 11 22 26 12 18 19 14 9 25 9 17 13 20 15 16B PARTS LIST ITEM 1 DESCRIPTION Pump Body QTY ITEM 1 15 DESCRIPTION QTY Shaft Lip Seal, 400 Motor Shaft 1 2 O-Ring Nitrile, -022 2 16A, 16B Motor Assembly (see charts below for motor specifics) 1 3 Sight Cap 2 17 Screw, ¼ - 10 x 2.25 PTS-SS 4 4 Bearing Ring 1 18 Flange Gasket - EPDM 2 5 Brushing, 1.
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL 400B Series Model Information LUBRICATING FLUIDS APPLICATIONS1 ACCESSORIES MODEL NUMBER INLET CONFIGURATION2 VOLTAGE DISCHARGE STEEL SUCTION INLET 1" MANUAL NOZZLE HOSE 3 HYTREL/NBR DIAPHRAGM FR205B AA No Accessories FR205BX054 24V DC UL EXP BB FR210B AA FR405BEXPX054 12V DC UL EXP FR410B X BB 12V DC UL EXP FR450B 12' No Accessories 12V DC FR410BEXP X AA 115V AC X X 12' X X 12' X X 12' ACCESSORY CONFIGURATORS BY
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL 400B Series Model Information (continued) CHEMICALS: AGRICULTURE & INDUSTRIAL1 ACCESSORIES SUCTION INLET DISCHARGE SANTOPRENE / EDPM DIAPHRAGM MODEL NUMBER SS411BCEXP SS413BCEXPPG SS415B SS415BX670 SS415BEXPX670 SS415BX731 SS415BX731PG VOLTAGE 12V DC CE EXP INLET POLY 2 HOSE 3 ANTI‑DRIP POLY FF EE 12V DC AA 12V DC UL EXP EE 12V DC W/ BRACKET AA HOSE 3 SPECIAL No Accessories - 39" X 12' VERSION4 - Pump-N-Go A No Accessories X
| 400B SERIES ELECTRIC DIAPHRAGM PUMPS OPERATION MANUAL Regulatory Compliance Information The “400B CE” Series pumps comply with the European Directive 2006/42/EC Machinery Directive The following standards were used to verify conformance: Specific models of the 400 Series pumps feature UL/cUL listed electric motors. Check your model versus the MODEL / ACCESSORIES / CONFIGURATION INFORMATION table (page 14-15) to determine how your particular pump is equipped.
POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B Manuel de l’utilisateur
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Table des matières Garantie limitée.................................................................................. 3 Merci! Définitions importantes...................................................................... 3 Merci pour votre loyauté envers la marque de pompes de transfert de produits chimiques, lubrifiants et hydrocarbures mixtes Sotera®.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Garantie limitée À COMPTER DE LA DATE D’ACHAT SÉRIE DE PRODUITS Cinq (5) ans Pompe série 400 seulement (tous modèles) Moteur et compteurs non inclus Deux (2) ans Compteurs 820, 825 et 850 Un (1) an Tous les moteurs, indépendamment de la classe de tension (antidéflagrant, non antidéflagrant; 12 Vcc, 24 Vcc et 115 Vca) Accessoires tels que raccords, flexibles, tuyaux, joints articulés, filtres et crépines achetés dans le cadre d’une
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR À propos de ce manuel Du concept initial jusqu’à la fabrication finale, ce produit Sotera est construit pour offrir des années d’utilisation sans problème. Pour assurer votre sécurité et celle de votre entourage, il est impératif de lire ce manuel en entier avant de tenter d’installer ou de faire fonctionner ce nouveau produit.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Information sur la sécurité AVERTISSEMENT Les pompes de la série 400B ne sont pas conçues pour le ravitaillement d’avions, de véhicules routiers ou non routiers ni de bateaux. Cette pompe ne convient pas à une utilisation avec des fluides destinés à la consommation humaine.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Pratiques exemplaires d’installation (côté refoulement de la pompe) • Tous les flexibles de refoulement doivent avoir un diamètre d’au moins 1 po.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Alimentation à courant continu (suite) • Tous les modèles 12 Vcc non antidéflagrants sont équipés d’un câble d’alimentation. Les modèles de 12 Vcc ont un porte-fusible et un fusible de 30 A DANGER • Les modèles antidéflagrants de 12 Vcc et 24 Vcc ne sont pas équipés d’un cordon d’alimentation, mais peuvent comprendre un câble d’alimentation séparé, en fonction de la configuration du modèle Toutes les pompes c.a.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Meilleures pratiques d’utilisation L’entretien régulier est essentiel au maintien du rendement et à la durabilité de la pompe série 400B. • Toujours mettre la pompe de transfert à l’arrêt et la débrancher de la source d’alimentation avant toute intervention • Toujours purger la pompe complètement avant tout entretien ou démontage. Tuthill recommande d’utiliser de l’eau pour rincer les produits chimiques agricoles et industriels.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Remplacement des membranes L’entretien des ensembles de membrane et clapets antiretour peut se faire sans vidanger l’huile de la cavité intérieure du corps de pompe. Il est important de ne démonter qu’une (1) seul ensemble à la fois. Éviter toute contamination potentielle de l’huile dans la cavité interne de la pompe durant cette opération. Procédure 1.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Table de correction de viscosité DÉBIT EN LITRES PAR MINUTE (L/min) 7,6 15,1 22,7 30,3 37,9 45,4 53 60,6 15,2 45 13,7 40 12,2 35 10,7 30 9,1 25 7,6 20 6,1 15 4,6 10 3 LONGUEUR DE FLEXIBLE DE REFOULEMENT DE D.I. 1 PO (MÈTRES) LONGUEUR DE FLEXIBLE DE REFOULEMENT DE D.I.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Trousse embout de buse antigoutte 400KTF0237 S’utilise avec les buses Norwesco et autres de diamètre extérieur de 30 mm (1-3/16 po). Embout de buse antigoutte Installation Buse 1. S’il y a un cran en plastique en saillie sur la buse, l’éliminer avec précaution à la lime avant de poser l’embout antigoutte 2. Appliquer de l’eau savonneuse sur l’extrémité pour faciliter la pose.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Guide de dépannage SYMPTÔME La pompe ne s’amorce pas La pompe ronfle mais ne tourne pas Faible capacité de la pompe Le moteur surchauffe Fuite de liquide sotera.
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR 9 17 19 18 3 1 2 4 21 27 28 5 6 24 7 23 8 16A 9 10 11 22 26 12 18 19 14 9 25 9 17 13 20 15 16B LISTE DES PIÈCES REPÈRE DESCRIPTION QTÉ REPÈRE 1 Corps de pompe 1 15 2 Joint torique en nitrile, -022 2 16A, 16B DESCRIPTION QTÉ Joint à lèvre d’arbre moteur 400 1 Ensemble moteur (voir les caractéristiques de moteurs dans la table ci-dessous) 1 3 Capuchon de jauge visuelle 2 17 Vis, 1/4 - 10 x 2,
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Information sur les modèles série 400B UTILISATIONS AVEC DES LIQUIDES LUBRIFIANTS1 ACCESSOIRES NUMÉRO DE MODÈLE CONFIGURATION D’ENTRÉE2 TENSION REFOULEMENT ENTRÉE D’ASPIRATION EN ACIER BUSE MANUELLE 1 po FLEXIBLE3 MEMBRANE EN HYTREL/NBR FR205B AA Pas d’accessoire FR205BX054 24 Vcc UL ANTIDÉF FR210B BB AA FR405BEXPX054 12 Vcc UL ANTIDÉF FR410B X BB 12 Vcc UL ANTIDÉF FR450B 3,7 m (12 pi) Pas d’accessoire 12 Vcc FR410B
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Information sur les modèles série 400B (suite) PRODUITS CHIMIQUES : AGRICOLES ET INDUSTRIELS1 ACCESSOIRES ENTRÉE D’ASPIRATION REFOULEMENT MEMBRANE EN SANTOPRENE / EDPM NUMÉRO DE MODÈLE TENSION SS411BCEXP SS413BCEXPPG SS415B SS415BX670 SS415BEXPX670 SS415BX731 SS415BX731PG ENTRÉE POLY2 FLEXIBLE3 ANTIGOUTTE POLY FF 12 Vcc CE ANTIDÉF EE 12 Vcc AA 12 Vcc UL ANTIDÉF EE 12 Vcc AVEC SUPPORT AA FLEXIBLE3 SPÉCIAL VERSION4 Pas d
| POMPES À MEMBRANE ÉLECTRIQUES SÉRIE 400B MANUEL DE L’UTILISATEUR Information sur la conformité réglementaire Les pompes série « 400B CE » sont conformes à la directive européenne 2006/42/CE (Directive Machines) Les normes suivantes ont été utilisées pour vérifier la conformité : EN 809:1998 +A:2009 – Pompes et unités de pompes pour liquides – exigences communes en matière de sécurité Certains modèles de pompes série 400 comportent des moteurs électriques homologués UL/ULC.
BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B Manual de operación del propietario
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Contenido Política de garantía limitada............................................................... 3 ¡Gracias! Definiciones básicas........................................................................... 3 Gracias por su lealtad con la marca Sotera® de bombas de transferencia de productos químicos, lubricantes e hidrocarburos mixtos.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Política de garantía limitada DESDE LA FECHA DE VENTA SERIE DEL PRODUCTO Cinco (5) años Solo bombas serie 400 (todos los modelos) No se incluye el motor ni los medidores Dos (2) años Medidores 820, 825 y 850 Un (1) año Accesorios, definidos como conectores, mangueras, Todos los motores, sin importar la clase de voltaje (a prueba destorcedores, filtros que se compren dentro del paquete de de explosiones, no a prue
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Acerca de este manual Desde el concepto y el diseño inicial hasta la producción final, su producto Sotera está fabricado para brindarle años de uso sin problemas. Para garantizar su seguridad y la de quienes lo rodean, resulta crucial que lea este manual en su totalidad antes de intentar instalar u operar su nuevo producto.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Información de seguridad general ADVERTENCIA Las bombas de la serie 400B no están diseñadas para usarlas en aeronaves, en vehículos para carreteras y todoterreno o en embarcaciones marinas. Esta bomba no es adecuada para su uso con líquidos para consumo humano.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Mejores prácticas de instalación (Lado de descarga de la bomba) • Todas las mangueras de descarga deberían tener un diámetro mínimo de 1 pulg. Los tamaños más grandes se pueden usar siempre que terminen en un diámetro de 1 pulg. en la salida de descarga de la bomba • Siempre use mangueras y accesorios que sean compatibles con el producto que se transfiera.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Alimentación de CC (continuación) • Todos los modelos no a prueba de explosiones de 12 V CC vienen con un cable de alimentación preinstalado.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Mejores prácticas operativas El mantenimiento regular es fundamental para mantener el rendimiento y prolongar la vida útil de su bomba serie 400B. • Siempre apague la bomba de transferencia y desconéctela de la fuente de alimentación antes del mantenimiento • Siempre enjuague completamente la bomba antes de cualquier mantenimiento o desmontaje.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Reemplazo del conjunto de diafragma Se puede realizar mantenimiento a los conjuntos de diafragma y de válvula de retención sin retirar el aceite de la cavidad interior del cuerpo de la bomba. Es importante que solo se realice mantenimiento a un (1) conjunto a la vez. Evite que toda la contaminación posible del aceite al interior de la cavidad interna de la bomba durante esta reparación. Procedimiento 1.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Tabla de corrección de viscosidad FLUJO EN LITROS POR MINUTO (LPM) 7,6 15,1 22,7 30,3 37,9 45,4 53 60,6 15,2 45 13,7 40 12,2 35 10,7 30 9,1 25 7,6 20 6,1 15 4,6 10 3 5 1,5 0 0 0 2 4 6 8 10 12 14 LONGITUD DE MANGUERA DE DESCARGA DE 1 PULG. DE DIÁMETRO INTERIOR (METROS) LONGITUD DE MANGUERA DE DESCARGA DE 1 PULG.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Kit de tubo de boquilla antigoteo 400KTF0237 Para uso con boquillas Norwesco u otras, con un diámetro exterior de 30 mm (1-3/16 pulg.). Tubo de boquilla antigoteo Instalación Boquilla 1. Si existe una muesca de plástico levantada en la boquilla, quítela cuidadosamente con una lima, antes de instalar el tubo antigoteo 2. Aplique agua con jabón en el extremo para facilitar la instalación.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Guía de solución de problemas SÍNTOMA La bomba no ceba La bomba emite un zumbido, pero no gira Capacidad baja de la bomba Sobrecalentamiento del motor Fugas de líquido sotera.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO 9 17 19 18 3 1 2 4 21 27 28 5 6 24 7 23 8 9 16A 10 11 22 26 12 18 19 14 9 25 9 17 13 20 15 16B LISTA DE PIEZAS ELEMENTO DESCRIPCIÓN CANT. ELEMENTO DESCRIPCIÓN 1 Cuerpo de la bomba 1 15 2 Sello o-ring de nitrilo, -022 2 16A, 16B 3 Tapa con mirilla 2 4 Anillo del cojinete 5 Casquillo, 1,250 diámetro exterior x 1,00 diámetro interior 6 CANT.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Información de modelo de la 400B APLICACIONES DE LÍQUIDOS LUBRICANTES1 ACCESORIOS NÚMERO DE MODELO CONFIGURACIÓN DE ENTRADA2 VOLTAJE DESCARGA ENTRADA DE SUCCIÓN DE ACERO BOQUILLA MANUAL DE 1 pulg. MANGUERA 3 DIAFRAGMA DE HYTREL/NBR FR205B AA Sin accesorios FR205BX054 24 V CC UL EXP. BB FR210B AA FR405BEXPX054 12 V CC UL EXP. FR410B X BB 12 V CC UL EXP.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Información de modelo de la serie 400B (continuación) PRODUCTOS QUÍMICOS: AGRÍCOLAS E INDUSTRIALES1 ACCESORIOS ENTRADA DE SUCCIÓN DESCARGA DIAFRAGMA DE SANTOPRENE / EDPM NÚMERO DE MODELO VOLTAJE SS411BCEXP ENTRADA POLIPROPILENO 2 MANGUERA 3 POLIPROPILENO ANTIGOTEO FF Sin accesorios 12 V CC CE EXP. SS413BCEXPPG EE SS415B 12 V CC AA 12 V CC UL EXP. EE 12 V CC CON SOPORTE AA - 1m (39 pulg.
| BOMBAS DE DIAFRAGMA ELÉCTRICAS DE LA SERIE 400B MANUAL DE OPERACIÓN DEL PROPIETARIO Información de cumplimiento normativo Las bombas serie “400B CE” cumple la Directiva europea 2006/42/CE relativa a las máquinas Se usaron las siguientes normas para verificar el cumplimiento: Modelos específicos de las bombas serie 400 cuentan con motores eléctricos en la lista UL / cUL.