0dBFS = 18dBu 0 2 4 6 8 10 12 14 16 18 21 24 27 30 35 40 MIX dBFS STE-1 RIGHT STE-2 STEREO INPUTS SELECT XD IN SOLO AE S/ EB U MUTE OU T EXIT OU W OR D CL /SU OC PE R IN K T IN S/ PD IF FUNCTION OU T M ID I IN W CL ORD OC OU K T PARAMETER TH RU CHANNEL / GROUP LINK 328 XD X D KORG 1212
328XD AND KORG 1212 Connecting the system 2 328XD Configuration 3 Korg 1212 Configuration 5 Using the 1212 with the 328XD 8 Additional Information 9 1 Soundcraft 328XD and Korg 1212 Setup Guide
CONNECTING THE SYSTEM Audio Connections Audio connections should be made as shown in the diagram below. Toslink optical cables must be connected between the ADAT Out ports of the 1212 card to the ADAT In ports of the 328XD and vice versa. Coaxial digital S/PDIF cables must also be connected from the 1212 S/PDIF output to the 328XD S/PDIF input and vice versa.
328XD CONFIGURATION Wordclock To configure the 328XD as the wordclock master, enter the 328XD Menu page by pressing the
S/PDIF Input The 328XD S/PDIF input can be routed to any one of the following inputs: Stereo Input 1, Stereo Input 2, FX-1, FX-2, 2 Track Tape Return, provided that the AES/EBU input has not already been assigned to that input. Commonly the 1212 S/PDIF output would be routed to Stereo Input 2, or the 2 Track Tape Return input. NOTE: Assigning a digital source to an input will override any analogue signal present on that input.
1212 CONFIGURATION Wordclock The 1212 must be set up to receive the wordclock transmitted by the 328XD (via the BNC connection).
Click on the ‘Clock Source’ pull-down menu in the ‘Word Clock & Sample Rate’ section, and select ‘S/PDIFClockIn’. This sets the 1212 to receive wordclock from its BNC input: Sample Rate Now the 1212 must be configured to playback at the same sample rate as the 328. Click on the ‘Sample Rate’ pull-down menu in the ‘Word Clock & Sample Rate’ section. Here the sample rate which the 1212 plays back can be set between 44.
This should be set to the same sample rate as the 328XD was set to in the ‘Wordclock’ section in chapter 2 of this manual. If the 328XD and 1212 are set to different sample rate settings, audio from the 1212 will play back at the incorrect speed. Saving Settings Now click on the ‘File’ drop-down menu, and click on ‘Save as Default… ’: Answer ‘OK’ to the window that follows, to confirm that you wish to save the current settings as the default settings.
USING THE 1212 WITH THE 328XD Accessing the 1212 ADAT I/O from the 328XD The 1212 will commonly be used with a software sequencer / hard disk recorder to allow play back and record 8 individual tracks of audio, via the ADAT I/O. Here, the software application must be configured to access the 1212 ADAT I/O via the relevant Windows device drivers that came with the 1212.
ADDITIONAL INFORMATION If used in conjunction with an ADAT, the system should be connected as follows: 9 Soundcraft 328XD and Korg 1212 Setup Guide
SOUNDCRAFT HARMAN INTERNATIONAL INDUSTRIES LTD CRANBORNE HOUSE CRANBORNE ROAD POTTERS BAR HERTS EN6 3JN UK TEL: +44 (0) 1707 665000 FAX: +44 (0) 1707 660742 EMAIL: info@soundcraft.com SOUNDCRAFT USA 1449 DONELSON PIKE NASHVILLE TN 37217 USA TEL: 1-615-360-0471 FAX: 1-615-360-0273 EMAIL: soundcraft-usa@harman.com www.soundcraft.