INSTRUCTION MANUAL Stereo Radio Double Cassette Recorder with 3 CD Changer and Turntable HCD 9933PR
TROUBLE SHOOTING Power switch on, but no power Record button cannot be pressed in • Check power to wall outlet. • Check AC cord connection to wall plug. • Cassette erase-protection tab is removed. Use another cassette or apply adhesive tape over tab hole. Power Indicator is on, but no sound from speakers Poor Recording • Check Function selector. • Check VOLUME setting. • Make sure headphones are not plugged in.
CONTROLS 4 1 5 16 6 17 18 8 7 2 3 19 20 21 9 22 10 11 12 23 24 25 26 13 27 14 28 15 29 31 32 33 34 30 35 36 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) Plak-up Holder Speed Selector Spindle Adapter LCD Display CD Skip Backward button Power button Power Standby button Remote Sensor Extra Bass Selector Phones Jack CD Mode button Tuner/Band Selector Tape Selector Deck 1 Control RECORD (recode) button - DECK A only PLAY (playback) button REW (rewind) button F.
REMOTE CONTROL This unit comes with a Remote Control which allows the user to control certain system functions from a distance of up to 20 feet. The Remote Control requires two AAA batteries (not included). REMOTE CONTROL RANGE Remote Control Sensor NOTE : The Remote Control should always be aimed at the Remote Control Sensor on the unit for best performance. Remote Control Functions: NOTE : 30 Degrees POWER button on main unit must be 'ON' in order for Remote Control to operate. 1.
CONNECTIONS HEADPHONE JACK (PHONES) POWER CONNECTION REMOTE CONTROL This unit will accept stereo headphones (not included) with a 1/8" plug and an impedance of 16 ohms or greater. The speakers are automatically disconnected when headphones are connected to the PHONES jack. Connect the power cord to AC outlet only. SPEAKER JACKS Connect the SPEAKER PLUGS to the SPEAKER JACKS located on the rear of the unit.
PHONO Note : 6. Place the tone arm to the desired position. 7. Adjust VOLUME & EXTRA BASS controls to the desired sound level and sound equalization. 8. At the end of record, the platter will automatically stop rotation. Lift the tone arm from the record and return it to the rest. 9. To stop manually, lift the tone arm from the record , and return it to the rest. Remove the stylus protector. Be sure that the tone arm is detached from the tone arm rest before operation and re-secured again afterward. 1.
CASSETTE PLAYBACK (DECK B) (DECK A) Fast-Forward and Rewind The TAPE B is used for playback only. The TAPE A is used both for recording and playback. For fast winding or rewinding the tape, press the F.Fwd or REW button. Press the STOP/ EJECT button when the desired location has been reached. When the end of the tape has been reached, the reels will stop. Then the STOP/EJECT button should be pressed. Do not turn the unit off while the tape is running. Otherwise, the pinch roller may be damaged. 1.
DUBBING (DECK B) TO (DECK A) This unit enables you to duplicate a prerecorded tape to another tape by using the unit-in double deck mechanisms. It is performed only one way, from the DECK B (playback) to DECK A (recording). Dubbing at normal Speed Note: Be sure the HIGH SPEED DUBBING switch is SET AT NORMAL in order to record at normal speed. 1. 2. 3. 4. 5. 6. Press the POWER switch to ON. Set the TAPE function selector. Insert a pre-recorded cassette into the DECK B and a blank cassette into the DECK A.
Safety Instruction : Do not connect the power cord to the mains supply until all other connections have been made. Do not expose this apparatus to dripping or splashing HANDLING COMPACT DISCS To remove a disc from its storage case, press down on the centre of the case and lift the disc out, holding it carefully by the edges. Fingerprints and dust should be carefully wiped off the disc's recorded surface with a soft cloth.
LOADING CDS 1) Press the POWER button to turn the unit on. 2) Select the CD FUNCTION button. The CD Disc tray will turn to check if any discs are present. If no discs are in the tray, NO DISC will appear in the display. 3) Press the OPEN/CLOSE button to open the disc compartment. The CD tray will open, exposing the right and left disc holders. The third disc holder will remain in the unit. To expose the third disc holder, press one of the DISC No. buttons.
CAUTION Do not put anything except a compact disc into the compartment. Foreign objects can damage the mechanism. Do not force the compartment by hand during the opening and closing operations. Keep the disc compartment closed when not in use to prevent dirt and dust from entering the mechanism. Never place more than one disc in each tray at any time. If the disc is deeply scratched, or too dirty, the disc may not play.
Listen to Programmed Tracks Press the PLAY/PAUSE button. Disc play will start at the beginning of the first programmed track. To Clear The Program Memory If the disc is playing, press the STOP button. Press the STOP button again until the MEMORY Indicator does not appear. The program memory will also be cleared if the disc compartment is opened, if the function is changed, or if the power is switched off.
REPEAT DISC PLAY BY REMOTE CONTROL This function allows the operator to repeat a single track, all of the tracks of one CD or with all of the tracks on all 3 CD's. 1. REPEAT ALL Disc Press REPEAT Disc once "REPEAT DISC ALL" appears in the display Press PLAY/PAUSE to start play 2. REPEAT 1 Disc Press REPEAT twice - "REPEAT DISC 1" appears in the display Select the disc to play by pressing the Disc No button and press PLAY/PAUSE /II to start play 3.
INTRO BY REMOTE CONTROL Operates in STOP or PLAY mode 1. Press INTRO once, each song will play for 10 seconds. 2. Press INTRO twice to delete this function. Unit will resume normal play. SLEEP BY REMOTE CONTROL 1. Press SLEEP once, "SLEEP 90" will appear on LCD. This means unit will be stopped & turned to STAND BY mode in 90 minutes. Keep pressing SLEEP for about 5 seconds, "80, 70, 60, 50..." will appear on LCD to allow selection on the desired sleep time. 2. Press SLEEP twice to delete this function.
TRACK SKIP Starting disc play from the beginning of a particular track Press the Forward or Reverse SKIP/SEARCH buttons to select the desired track. The number of the selected track will be shown on the CD display. Press the PLAY/ PAUSE button to start play. To skip to the next track on a disc For example, to skip ahead to the beginning of track 2 while track 1 is playing. Press the FWD SKIP/SEARCH button. Disc play will resume at the beginning of track 2.
