KD-X560BT MONITOR WITH RECEIVER INSTRUCTION MANUAL • Updated information (the latest Instruction Manual, etc.) is available from .
Contents Before use................................................................................. 2 How to read this manual...................................................................................2 Precautions................................................................................................................2 Getting Started....................................................................... 3 Initial Settings......................................................................
Getting Started Initial Settings Clock settings 1 Press an hold < > to display the general setting. 2 Press / to select [ ]. 3 Turn the volume knob to select [Time Format], then press the knob to select the time format ([12h] or [24h]). 1 Turn the ignition key of your car to ACC. The unit is turned on. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. 4 Turn the volume knob to select [Date/Clock], then press the knob.
Basics Basics Volume knob (turn/press) Detach button Common operations Select a source 1 Press < > to display the HOME screen. HOME screen appears. ÑÑTurning on the power 1 Press < >. 2 Turn the volume knob to select the source, then ÑÑTurning off the power 1 Press and hold < Remote sensor Monitor press the knob. 1 >. ÑÑAdjusting the volume 2 3 5 6 4 1 Turn the volume knob. ÑÑMutes the sound 1 Press and hold the volume knob. appears when the mute function is active.
USB USB Preparation Playback operations ÑÑConnecting a USB device 1 Open the front port cover. 2 Connect the USB device with the USB cable. The unit reads the device and playback starts. • USB maximum power supply current : DC 5 V = 1 A ÑÑTo disconnect the USB device: 1 Press < > to display the HOME screen. 2 Turn the volume knob to select other than [USB], then press the knob. 3 Detach the USB device.
USB ÑÑSelecting a track in a list (Searches file) 1 Press < > to display the LIST screen. 2 Press / to select whether you search by audio files [ picture files [ ]. ], video files [ ] or Function settings 1 Press < > to display the function menu. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. 3 Press < ✎✎NOTE > to exit. • If no operation is done for about 10 seconds, the operation will be canceled.
iPod/iPhone iPod/iPhone Ñ Source screen Preparation Ñ Connecting iPod/iPhone 1 Open the front port cover. 2 Connect the iPod/iPhone using the KS-U62 2 (optional accessory). 1 Ñ To disconnect the iPod/iPhone 1 Playback status/Playing time/Total playing time Play time bar : For confirmation of current playing position : Repeat playback mode indicator : Random playback mode indicator 2 Displays the information of the current file. > to display the HOME screen.
Tuner Tuner Tuner Basic Operation Tuner function settings 1 Press < > to display the function menu. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. 3 Press < ✎✎NOTE 1 Press < > to display the HOME screen. 2 Turn the volume knob to select [FM] or [AM], then press the knob. • If no operation is done for about 10 seconds, the operation will be canceled. Manual Store 3 Press / to search for a station automatically. “Auto Seek” appears.
External Components Using external audio players Rear view camera To use a rear view camera, the REVERSE lead connection is required. For connecting a rear view camera. (P.18) 1 2 1 3.5 mm stereo mini plug (Sold separately) Use a 3-core plug head stereo mini plug for optimum audio output. 2 Portable audio player (Sold separately) ÑÑDisplaying the picture from the rear view camera The rear view screen is displayed when you shift the gear to the reverse (R) position.
Bluetooth smartphone Bluetooth smartphone ÑÑAbout the Bluetooth smartphone and Bluetooth audio player Receive a phone call This unit conforms to the following Bluetooth specifications: Version Bluetooth Ver.4.
Bluetooth smartphone Make a phone call Playing Bluetooth Audio Device 1 Press < 1 Press < > to display the HOME screen. 2 Turn the volume knob to select [BT Audio], then > to enter Bluetooth mode. press the knob. To Do this Press the volume knob. Play/pause Press / repeatedly. Select a file Press and hold /. Fast-backward/ Fast-forward 2 Press / to select a method to make a call ([ ]: from the calls history/[ the phone book).
Setup Setup Function settings Settings 1 Press < > to display the function menu. 2 Turn the volume knob to select the item to set (see the table below), then press the knob to make a selection. 3 Press < ✎✎NOTE > to exit. • If no operation is done for about 10 seconds, the operation will be canceled. Repeat All: Repeats all files. ( indicator lights up.) One: Repeats current file. ( indicator lights up.) Random OFF: Normal playback. ON: Randomly plays all files. ( indicator lights up.
Setup Bluetooth Settings Sync ON/OFF: Activates or deactivates the Phonebook synchronization of the phonebook in the connected mobile phone with the unit. BT Displays the information about the Information connected Bluetooth device (device name, phone name, Bluetooth version, and mac address). Sound settings 1 Press < > to display the sound setting. 2 Turn the volume knob to select an item (see the following table), then press the knob.
Remote control This unit can be operated using the remote control. The remote control RM-RK258 (optional accessory) can be used. !!WARNING • Do not ingest the battery, Chemical Burn Hazard The remote control supplied with this product contains a coin / button cell battery. If the coin/ button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children.
Installation Installation Before Installation Before installation of this unit, please note the following precautions. #WARNINGS • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow).
Installation ÑÑInstallation procedure ÑÑTrim plate 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Make the proper input and output wire connections for each unit. 3) Connect the wire on the wiring harness. 4) Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5) Take Connector A on the wiring harness and connect it to the external power connector on your vehicle.
Installation ÑÑRemoving the trim plate 1) Use the extraction key (accessory 4) to lever out the four tabs (two on the left part, two on the right part). 4 2) Pull the trim plate forward. ÑÑRemoving the unit 1) Remove the trim plate by referring to step 1 in “Removing the trim plate”. 2) Insert the two extraction key (accessory 3) deeply into the slots on each side, as shown. 3 3) Pull out the unit halfway. ✎✎NOTE • Be careful to avoid injury from the catch pins on the extraction key.
Installation ÑÑConnecting wires to terminals Connect to the vehicle’s parking brake detection switch harness. PRK SW Light Green (Parking sensor wire) For best safety, be sure to connect the parking sensor. REVERSE GEAR SIGNAL Purple/White (Reverse sensor wire) STEERING WHEEL REMOTE CONTROL Connect to vehicle’s reverse lamp harness when using the optional rear view camera.
Installation 15A 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 Accessory 7 Accessory 6 P.CONT ANT.CONT Blue/White (Power control/ Antenna control wire) *1 Connect either to the power control terminal when using the optional power amplifier, or to the power terminal for the booster amplifier of the film-type or short pole type antenna. (Max. 300mA, 12V) *1 If no connections are made, do not let the cable come out from the tab.
About this Unit About this Unit ÑÑAcceptable Video files Maintenance ÑÑCleaning the Unit If the front panel of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the front panel is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe it again with a clean soft dry cloth. !!CAUTION • Applaying spray cleaner directly to the unit may affect its mechanical parts.
About this Unit ÑÑiPod/iPhone No sound comes out of the speakers. • Disconnect the iPod/iPhone, then connect it again. • Select another source, then reselect “iPod”. The iPod/iPhone does not turn on or does not work. • Check the connecting cable and its connection. • Update the firmware version of iPod/iPhone. • Charge the battery of iPod/iPhone. • Reset the iPod/iPhone. Sound is distorted. • Deactivate the equalizer either on this unit or the iPod/iPhone. A lot of noise is generated.
About this Unit Specifications ÑÑMonitor section Picture Size : 3.0 inches (diagonal) wide Drive System : TFT active matrix system Number of Pixels : 320H x 240V x RGB Aspect Ratio : 16:9(wide) Back Lighting : LED ÑÑUSB interface section USB Standard : USB 2.0 High Speed File System : FAT 16/ 32, NTFS Maximum Power Supply Current : DC 5 V 1 A Audio Decoder : MP3/ WMA/ AAC/ WAV/ FLAC/ OGG Video Decoder : MPEG1/ MPEG2/ MPEG4/ H.
About this Unit ÑÑAudio section Maximum Power (Front & Rear) : 45 W Full Bandwidth Power (1% THD) : 17 W × 4 Speaker Impedance :4–8Ω Equalizer : 7 Band Band Frequency: 62.5/ 160/ 400/ 1k/ 2.5k/ 6.3k/ 16k Hz Level: -7 – +7 (-7 dB – +7 dB) LPF Frequency: 80/ 120/ 160 Hz ÑÑGeneral Operating Voltage : 12 V Maximum Current Consumption : 15 A Installation Dimensions (W × H × D) : 182 × 52 × 117 mm (with sleeve) 7-3/16 × 2-1/16 × 4-5/8 inch Weight : 0.66 kg (1.
About this Unit For USA For Argentina Ñ ! CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
About this Unit FCC STATEMENT Ñ device complies with Part 15 of the FCC Rules. 1. This Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
