SM-CMD2022 DVD/MP3/CD RECEIVER Instruction manual DVD/MP3/CD-
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ....................................................................................................... 2 Important safeguards .................................................................................................
Important safeguards Read carefully through the manual to familiarize yours with this high-quality sound system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. Do not attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes.
Installation/ Connections First complete the electrical connections, and then check them for correctness. If you are not confident working with electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. Before installing the unit, please remove two screws on the top. Before the installation 1. Remove the old unit from the dashboard. Remove the outer trim frame.
On the masking tape mark the polarity of the speaker wires (+ & -), as well as left or right, and front or rear. Repeat this procedure for all of the speakers. Mark the power, ground, and any other wires also. Installation method A After inserting the holder into the dashboard, select the appropriate tab and bend them inwards to secure the holder in place. Insert fingers into the groove in the front of frame and remove it. Insert the levers supplied with the unit to the grooves at both sides.
Use either truss screws (5 x 8mm) or flush surface screws (4 x 8mm), depending on the shape of the screw holes in the bracket. 2. Screw. 3. Factory radio mounting bracket. 4. Dashboard or Console. 5. Hook (Remove this part). Note: The mounting box, outer trim ring, and the Half-sleeve are not used for this method of installation. Detachable control panel Detaching the control panel 1. Press the OPEN button on the front panel. The panel will go down (pic. 1). 2.
Caution: DO NOT insert the control panel from the right side. It can damage the control panel. The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an Pic. 3 extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Connection scheme: 8
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections.
Accessories 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Name Hexagon nut M5 T (3.5 mm) Mounting box (0.6 mm) Left key (1.0 mm) Right key (1.0 mm) Metal bar (0.8 mm) ISO connector Plain washer =5 mm Carrying case Outer trim ring Spring washer =5 mm Screw 5X5 mm Screw 5X25 mm Screw M5 5X29.
Controls description Front panel 1. 2. 3. 4. 5. OPEN BUTTON Press it to remove the front panel. TA BUTTON In RADIO mode press it to active the TA function. / buttons In Disc mode press the buttons shortly to go to previous/next track. Press and hold them to start fast backward/ forward rewind. In Radio mode press the buttons shortly to search the stations manually. Press and hold for 2 seconds to start searching the stations automatically. PTY / CLK BUTTON Press it and hold for 2 seconds to set clock.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. / OSD button In menu use it to move to the left. During playback press it and hold for 2 seconds to show the mode information on the display. / RPT BUTTON In menu use it to move to the right. During playback press it and hold for 2 seconds to start repeat playback. / INT BUTTON In menu use it to move upward. During playback press it and hold for 2 seconds to start intro playback (about 10 seconds each track). / RDM BUTTON In menu use it to move downward.
16. 17. 18. 19. 20. 21. 22. In Radio mode press it to scan the preset memorized stations. Press it and hold for 2 seconds to store the programs with the best reception into preset buttons automatically. USB socket SD/MMC socket MUTE BUTTON Press it to switch the sound off/on. VOL KNOB / SEL BUTTON Rotate it clockwise to increase the volume level; rotate anticlockwise to decrease the volume level. Press it repeatedly to select the mode: VOL => BAS => TRE => BAL => FAD => LOUD => LOC => ST => EQ.
Back of the front panel Press the OPEN button to open the panel. 1. 2. 3. 4. LED INDICATOR RESET BUTTON DISK SLOT EJECT BUTTON Note: Pressing the RESET hole will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down, flashes when you remove the panel.
Remote control 1. MODE BUTTON 2. POWER BUTTON 3. BND/SYS BUTTON 4. ERROR BUTTONS 5. ENTER BUTTON 6. STOP/REVERSE BUTTON 7. AMS/RPT BUTTON 8. ST/PROG BUTTON 9. LOC/RDM BUTTON 10. VOL +/- BUTTON 11. PBC BUTTON 12. OSD BUTTON 13. DIGIT AREA 14. PLAY/PAUSE BUTTON 15. MUTE BUTTON 16. TITLE BUTTON 17. SUB-T BUTTON 18. SETUP BUTTON 19. ANGLE BUTTON 20. SLOW BUTTON 21. ZOOM BUTTON 22. SEL BUTTON 23. SEEK +/- / / BUTTONS 24. AUDIO BUTTON 25.
Changing the battery 1. Press the catch and at the same time pull out the battery tray. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. General operations Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press OPEN button and remove the panel, then press the RESET button to restore the unit to the original factory settings.
Mode selecting Press the MOD button on the front panel or MODE button on RC repeatedly to select the mode: RADIO => DISC (the type of disc inserted) => USB (if any is inserted) => CARD (the type of card inserted). Subwoofer control Press and hold the BAND/ NP/ SUB button on the panel to turn the Subwoofer output ON. An external amplifier is required to operate a subwoofer. Sound settings Press SEL button shortly and repeatedly to select the mode: VOL => BAS => TRE => BAL => FAD => LOUD => LOC => ST => EQ.
4. 5. 6. Press briefly the SEL button again, the minute will blink. Rotate the VOL knob on the panel to adjust minutes. Press the PTY/CLK button to confirm it.
Radio operations Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Band select Press the BAND button on the front panel or BND/SYS button on RC repeatedly to select your desired radio band during RADIO mode: FM1, FM2, FM3, AM1, AM2.
APS (Auto memory store/ Preset scan) function Preset scan: press APS button on the panel or AMS button on the RC to scan all preset stations in the memory of the current band and stay on each memory stations for about 5 seconds. To stop preset scan, press this button again. To listen to saved station press 1-6 buttons. Auto memory store: press APS button on the panel for more than 2 seconds to enter auto store mode.
TA (Traffic Alarm) function Press the TA button on the panel to select TA ON or TA OFF. In TA mode traffic program will be automatically searched, until the program is received. When traffic announcement is received the unit will temporarily switch to the tuner mode (regardless of the current mode) and begin broadcasting the announcement. After the traffic announcement is over, it will return to the previous mode and volume level.
PTY (Program Type) 1. Press PTY/CLK button on the panel to activate the PTY function. The previous PTY type is shown. 2. Press PTY/CLK once again to enter the MUSIC type or press twice to enter the SPEECH type, then use buttons 1 - 6 to select the desired program type (see the following table). 3. 4. 5. When PTY is selected, the radio starts to search corresponding PTY information, and stops if the corresponding PTY information is detected.
- - - - TA SEEK When newly tuned station does not receive TP information for 5 seconds, the radio retunes to next station which has not the same station (PI – Program Information) as the last station, but has the TP information. When TP information gets lost at the current station for retune time which is set by RETUNE SHORT (30 seconds) or RETUNE LONG (90 seconds), the radio starts to retune to next same PI station.
Discs operations Disc glossary PBC (PlayBack Control) PBC is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc contains still images, it can playback high definition of still image. Title The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes possible to record several films on one disc.
MPEG 1(*.dat) Picture file: JPEG (*.jpg) ISO 9660 or ISO 9660 +Joliet format - Max. 30 characters Max. Track number is 448 Max. nested directory is 8 levels The max. album number is 99 The max. length of each track is 99 minutes 59 seconds Supported sampling frequency for MP3 disc: 8 KHz – 48 KHz (44.1 KHz preferably) Supported bit-rates of MP3 disc are: 32 - 320 kbps (128 kbps preferably). Following formats are NOT supported *.ACC, *.DLF, *.M3U, *.PLS, MP3 PRO, files with DRM.
Note: USB format supports 2.0. Capacity: 8 MB ~ 1 GB. SD cards brands: Cannon, Fuji film, Palm, Motorola, Microsoft, IBM, HP, Compaq, Sharp, Samsung, etc. Capacity: 8 MB ~ 1 GB. MMC cards brands: Ericsson, Nokia, Motorola, HP, Palm, Sanyo, Microsystems, etc. Capacity: 16 MB ~ 1 GB. Inserting the SD/ MMC card/ USB device Insert the MMC/ SD card or USB device into MMC/ SD compartment or USB socket. Then the playing mode will be changed into MMC/ SD or USB mode automatically.
Press the button on the RC or on the panel to play the next track. Scanning forward and backward Press and hold the or button on the RC or on the panel to fast the playing in backward or forward direction. Release the button when the desired location is found. Slow playback (for DVD/VCD) During DVD / VCD playback press the SLOW button on the RC to execute the SLOW function.
Changing size Press the ZOOM button on RC. The picture will be enlarged accordingly: X2, X3, X4, 1/2, 1/3, 1/4, OFF. Selecting the audio language (for DVD only) Press the AUDIO button on RC or press the SEL button to select AUDIO and then rotate the VOL knob to select the audio language (if DVD disc supports several audio languages). Changing angle (for DVD only) If DVD disc supports multi-angle playback, press ANGLE button on RC to play images in different camera angles.
Press PBC button on the RC to activate PBC menu on screen during playback. If the menu consists a list of titles, you can select a desired one using the / / / buttons on the RC or digit buttons. 3. The VCD starts playing the selected title automatically or press PLAY/ PAUSE / ENTER button to confirm the selected track for playback. 4. Press PBC again to exit menu. GOTO function During the playback press the GOTO button on the RC to enter the search mode.
Notes on MP3 and WMA MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs. The unit can read MP3 files written in the format compliant with ISO 9660. However it does not support the MP3 data written by the method of packet write. The unit can not read an MP3 file that has a file extension other than “.mp3”. If you play a non- MP3 file that has the “.mp3” extension, you may hear some noise.
Notes on creating your own CD-Rs or CD-RWs containing MP3 files To enjoy high quality sound, we recommend converting to MP3 files with a sampling frequency of 44.1 kHz and a fixed bit rate o f 128 kbps. DO NOT store more than 256 MP3 files per disc. For ISO 9660 - compliant format, the maximum allowable depth of nested folders is 8, including the root directory (folder). When CD-R disc is used, playback is possible only for discs, which have been finalized.
System setup Press SETUP button on the RC to display setup screen, use the desired item: System, Language, Audio, Video, Digital. / , ENTER buttons to select System setup TV system Select the TV system in the setting menu (PAL or NTSC). Screen saver The screen saver appears if disc stop last more than 3 minutes. Original setting: On. Video output mode Original setting: INTERLACE-YUV. TV type Select TV type to watch wide screen movies. 4:3 Pan Scan: For 4:3 TV, left and right edges will be cut.
If this item is selected, the unit will return to original setting. Language setup Setting the on-screen display language Select the language to be used for the on-screen display. Setting the audio language Select the language to be used for the audio. You can select a preferred audio from those included on the DVD video disk. (The screen on your player may have difference with the screen shown here) Setting the subtitle language Select the language to be used for the Subtitles.
Video setup Brightness. Set the brightness of the video output with / . Contrast Set the contrast of the video output with / . Hue. Set the hue of the video output with / . Saturation. Set the saturation of the video output with Sharpness. Set the sharpness of the video output with / . / . Digital setup Output mode Select the output mode: LINE OUT: Compress the input signal. The volume is small. RF REMOD: The volume is large.
Anti-theft system Remove the panel 1. Press POWER button to switch off the power of the unit. 2. Press OPEN button to flip down the panel. 3. Push the panel to the left and then pull it towards you. 4. Put it to the special box and take it with you. Remove the unit 1. Remove the panel and the trim plate. 2. Insert both T-Keys into hole on the front of the set until they lock. 3. Pull out the unit.
Cleaning Discs holding Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not touch its surface. Discs should be stored in their cases after use to avoid scratches. Do not expose discs to direct sunlight, high humidity, high temperature or dust. Prolonged exposure to extreme temperature can wrap the disc (such as leaving the discs in your car during summertime). Do not stick or write anything on either side of disc.
Troubleshooting guide Symptom Cause Solution No power. The car ignition is not on. The fuse is blown. Disc cannot be loaded. Disc cannot be read. Presence of disc inside the player. Inserting the disc in upside down. Compact disc is extremely dirty or defective. Temperature inside the car is too high. Volume is in minimum. Wiring is not properly connected. Front panel is not properly fix into its place. If the power supply is properly connected to the car accessory switch the ignition key to “ACC”.
The radio does not work. The radio station automatic selection does not work. The antenna cable is not connected. The signals are too weak. 38 Insert the antenna cable firmly. Select a station manually.
Specification General. Power supply: Current consumption/Fuse: Maximum power output: Dimensions (W x H x D) Working temperature range: FM Stereo Radio. Frequency range: Usable sensitivity/ I.F. Frequency: 12V DC 10A & 1A 50Wx4 channels 178 x 51 x 178 mm -20º - +60º 87.5 - 108.0 MHz 3 uV/ 10.7 MHz AM Section.
. , . ! , .............................................................................................................40 ...........................................................................................41 / ..........................................................................................43 ...................................................................................................49 ...............................................................................................
, . . . , . , . , . , , , . . , . . , , , . , , , , . 41 , . .
, . . , , . 42 . .
/ , 1. , , . . . . , 2. . ! . . . , . . ( ). , . 43 (+ .
A , , , . . , , . , . , . . 1. , . .
8 2. 3. 4. 5. ), (4 . . ( . ). : OPEN ), . , . 1. 2. 8 . ( 45 ( . 1). . 2).
, 1. . ( . 3). : . .2 .1 , 2. . 2. , . . .3 : : . , . , , : . . . . , . 46 , .
4 , . .
ISO 1. ISO, , . 2. ISO , . , .
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 M5 T (3,5 (0,6 ) (1,0 (1,0 ) 1 1 1 1 1 1 1 1 1 2 4 1 1 1 1 1 ) ) (0,8 ) ISO =5 =5 5X5 5X25 M5 5X29,3 49
1. OPEN , 2. TA 3. / EJECT , . / TA. . 4. PTY / CLK . , , / 50 RDS . . PTY. .
5. 6. (1-6) / OSD . 7. . / RPT . 8. / INT . . 9. 10 . / RDM . . 10. 11. STOP SET/PAU 12. BAND / NP/ SUB BAND ( ) . . , PAL60 => AUTO. 13. . : NTSC => PAL => .
, USB/SD/MMC => AUX. 14. AUX 15. APS 16. 17. 18. : TUNER ( . SD/MMC MUTE MUTE, / . SEL . 22. ) => . USB 19. 20. 21. ) => DISC ( , SEL, FAD => LOUD => LOC => ST => EQ. , AF POWER . , , . : VOL => BAS => TRE => BAL => . / , AF. .
OPEN, 1. LED 2. 3. 4. .
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25.
1. 2. : . , (CR 2025 3V), 55 . .
RESET ( ) OPEN. . , . RESET, : , . POWER, POWER . 3 : , . VOL+/- , , , , . 56 , , . MUTE, , . . .
MODE, => DISK => USB => CARD ( ). : USB, CARD, DISK , . BAND/ SUB, . / : AUX => RADIO , SEL ) => BAS ( ). ) => FAD ( ) => LOC ( ) => TRE ( , / : VOL ) => BAL ( ) => LOUD ) => ST ( ) => EQ VOL +/- : VOLUME: 00, 02,......, 38, 39 BASS/TREBLE: -7, -6,......, 0, +1, +2,......+6, +7 BALANCE: 7L, 6L,......, L=R, 1R,......,7R FADER: 7R, 6R,......, R=F, 1F,......
: . 5 5 , . . , PTY/CLK, 3 SEL 58 PTY/CLK, . . . 5 , .
: / , RDS ( . ) RDS BAND/NP/SUB : FM1, FM2, FM3, AM1, AM2. BND/SYS : , 2 SEEK +/. : . , / , , / , . , SEEK +/. ( : 6 5 ). << -/ >> + . : ( . SEEK +/1~6, . ). 1~6. 59 .
AMS/RPT 5 : , . AMS/RPT. , AMS/RPT 2 : , ST. APS APS , 6 1~6. APS AMS/RPT ST/PROG SEL STEREO MONO. (LO . , VOL +/- SEL, SEL ON) , OFF). APS 1-6. VOL +/LOC/RDM . 60 , SEL, ). . . , . LOC (LO .
AF ( ) , RDS . AF AF. . RDS , . , . ON ( , .). 61 (ON) AF , AF.
TA ( ) (ON) . , , PTY ( , . FM- PTY , PTY/CLK, PTY. . , TA 5 , 2 . , . ( . . ) RDS, . L/S => MASK DP/IALL. (OFF). SEL 2 , . : TA SEEK/ALARM => RETUNE ) TP ( , VOL, : TA SEEK , 62 TA, . ALARM.
(Traffic Program – MASK ) . , ), PI Retune-L – : , , Retune TA SEEK 30 TA SEEK 90 TA , . MASK ALL. MASK ALL: ) RETUNE LONG (90 , . , MASK DPI: , ), TP. ALARM: RETUNE Retune-S TA Seek. RETUNE S: RETUNE L: - RETUNE SHORT (30 . . . TA SEEK. . , AF : MASK DPI VOL, : . , , 63 RDS.
PBC ( ) – , . PBC, . . 1, , 1 2 3. , , ( . . . 64 . ), , . – 3 . .
: CD/DVD/CDDA/CD-R/-RW/DVD±R/±RW. : DVD-video, SVCD/VCD/HDCD/MP3/MP4/WMA/ PictureCD/JPEG/ DivX/MPEG4. : : MP3 (*.mp3) WMA (*.wma) : MP4 (*.avi, DIVX3.11/4.0/5.0/6.0 and XVID) MPEG 2(*.vob) MPEG 1(*.dat) : JPEG (*.jpg) ISO 9660 ISO 9660 + Joliet 30 . – 448. -8 . – 99. - 99 59 . MP3 : 8 48 44,1 ). P3 : 32 - 320 128 ). : *.ACC, *.DLF, *.M3U, *.PLS, MP3 PRO, DRM. .
USB/ SD/ MMC MP3 USB ( SD/ MMC, 2 1 (SD/MMC). USB . FAT 12/ FAT 16/ FAT 32 FAT 12/ 16 ( 200 , 500 ), FAT 32 ( 200 , 500 ). : 32 / : 32 . (id3tag ver 2.0) / / : 32 . USB 2.0. ). . : USB: USB 2.0. :8M ~1 . SD: SD : Cannon, Fuji film, Palm, Motorola, Microsoft, IBM, HP, Compaq, Sharp, Samsung, . . :8M ~1 . MMC: MMC : Ericsson, Nokia, Motorola, HP, Palm, Sanyo, Microsystems, . : 16 M ~ 1 . USB/ SD USB. SD/MMC USB , . MODE, . USB USB. .
/ , . . PLAY/ PAUSE , PLAY/PAUSE . STOP/REVERSE STOP , , , . PLAY/PAUSE, , , . , . , . / . . 1. 2. DVD, VCD ENTER SLOW : 1/2, 1/3, 1/4, 1/5, 1/6, 1/7, 67 , , . .
AMS/RPT , LOC/RDM , , R . . RDM . . Intro 10 . INT, . , OSD , . . / AUDIO ( ). DVD / , ZOOM . : X2, X3, X4, 1/2, 1/3, 1/4, DVDANGLE , . , ( ) - DVD , , 68 . .
. DVD . 1. . . 2. 1. 1 . ( SUBTITLE ENTER, TITLE . 2. 3. , , DVD , . ENTER. . PBC ( VCD 1- . ) . VCD PBC, 2. . , , 3. – 4. 5. 6. . . STOP . ENTER, , , . 69 , . VCD.
GOTO , . GOTO . VCD GOTO, , ( ). , : 1 => 8 => 2 => 0 => 0 => 0. . DVD , , , . 18 ENTER GOTO, . , . 234, . , ( ). , : 1 => 8 => 2 => 0 => 0 => 0. . 70 00 , : 2 => 3 => 4. . ENTER, . . ENTER, , , 20 , , .
. => AUTO. ST/PROG button .
3 WMA 3 MPEG 3 . 3 CD-RW. 3, ISO 9660. . , 3, 3, “.mp3”. ”, CD-ROM, CD-R 3 , , . PC “ “.mp3”, ” , “ . ” “ 8, 256. , 3. 8 MP3” . , VBR, , . VBR: . WMA . WMA . 72 , .
WMA (Windows Media Audio) – Microsoft Corporation. , ( , , ( ). , ) , . CD-R MP3 3 , 44,1 256 3 3 8, CD-R . ISO , , , CD-R CD-RW, 128 . 9660, ( CD-RW . 16 . . , . 73 , , 3. CD-RW . ). MP3 CD-R . 3 CD-RW CD-R 1. ID3TAG. , , , 64 .
, SETUP / , . “ : ENTER, , , : , , ”. 3 . .
: INTERLACE-YUV. 4:3 PS: 4:3 LB: 16:9: . 4:3. 4:3, 16:9. 0000. 75 . .
1 (1) (8) : 8: . :8 . . , . .
. DVD .( ). DVD . .( . ). . ).
: SPDIF/ RAW: SPDIF/ PCM: . . . . / . / .
/ . / . / .
/ . : LINE OUT: RF REMOD: “Full”, . . . “line out”, . .
: 3. , POWER, OPEN, 1. 2. 3. 4. 1. 2. , , . . . , . . . , . 81 .
. , ( ). . , , . , . , ( ). , . . CD . ), , . , , . , 3 . CD 3 , 82 (8 , ( . , , ). , .
) ) . , . , , . , . 83 .
. , “ . . ”. . , . . . , . . . . . . . RESET . 30 . . 30 . , . . . . . . 84 . .
. 12 , 10A & 1A 50 4 178 51 : : ( )/ FM . : MW DVD : / . . : 178 / -20º - +60º 87.5 - 108.0 3 / 10.7 522-1620 DVD/SVCD/VCD/MP4/MP3/WMA/CD/HDCD/DV DAudio/MPEG4/DivX/Picture-CD/PhotoCD/CD-R/CD-RW/DVD±R/JPEG NTSC/PAL / 24 /96 / 0 - +/-30 16:9 4:3 / 500 1.0 , 75 2 RMS (+/-3 ) 20 – 20 60 /50 CD . 1000 ./ (A-vtd)/ . .