SM-CMD5001 2 DIN DVD/CD/MP3 RECEIVER with built-in 7” TFT display and TV Instruction manual 2 DIN DVD/CD/MP37” TFT-
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ............................................................................................... 2 Important safeguards ......................................................................................... 3 Accessories........................
Important safeguards Read carefully through the manual to familiarize yourselves with this unit. Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit. “CLASS 1 LASER PRODUCT” This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product.
Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified technician check the system. Always keep the volume low enough so that you can hear sounds from outside the vehicle. Should this product fail to operate properly, contact your dealer or nearest service center. Accessories 1. 2. 3. 4. 5. 6. 7. 8.
Installation/connection Installation method 1: DIN Front-mount 1. Insert the mounting sleeve into the dashboard. 2. Bend these claws outward for a tight fit, if necessary. 3. Push in the unit and install the outer trim ring on it. Installation method 2: Installation using the screw holes at the sides of the unit.
Detach the unit 1. Take out the outer trim ring. 2. Insert the keys supplied to the unit at both sides of the unit (as illustrated) until they click. Pulling the keys makes it possible to remove the unit from the dashboard.
Electrical Connection 7
Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the color code table below for speaker and power cable connections.
Parking wire connection If Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled by driving status, system setup and input video sources. When the car is moving ahead, if the video disc is played, the screen shows “Attention! You cannot use this function while driving”, and blank screen. The above warning screen will prevent the driver from watching images.
Unit controls Front panel 1. VOL+/- buttons 2. PWR/SRC button 3. MENU/SEL button 4. TFT display 5. MUTE/- button 6. BAND/+ button 7. REL button 8. IR sensor 9. RES button (reset hole) Inner panel 1. Eject button 2. Memory card slot 3.
Remote controller (RC) 1. AF/EQ button 2. PWR/SOURCE button 3. GOTO button 4. BAND/TITLE button 5. AMS/MENU button 6. LOC/SUB-T button 7. ST/AUDIO button 8. PTY/ANGLE button 9. OSD button 10. ZOOM button 11. SLOW button 12. P/N button 13. PROG button 14. MUTE button 15. VOL- button 16. TA/LOUD button 17. EJECT button 18. Number buttons 19. UP cursor/NEXT button 20. CLEAR button 21. LEFT cursor/REWIND button 22. RIGHT cursor/FORWARD button 23. ENTER/PLAY button 24. SETUP button 25.
Changing the battery 1. Press the catch and at the same time pull out the battery tray (pic. 1). 2. Insert the 1 lithium battery, type CR2025 (3V) battery with the stamped (+) mark facing upward. Insert the battery tray into the remote controller (pic.2). Pic. 1 Pic. 2 Warning: Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately. Do not recharge, short, disassemble or heat the battery or dispose it in a fire.
General operations Touch screen Due to the touch screen, you can fulfill most functions not only by pressing buttons but also by touching the options you need. Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press RES button on the unit with a pointed object (such as a ballpoint pen) to set the unit to initial state.
Volume control Press VOL+/VOL- button on the RC or +/- on the unit to increase/decrease the sound level. Setting the sound characteristics Repeatedly press SEL button on the RC or MENU/SEL button on the unit to select the desired parameter in the following order: VOL => BALAN => FADE => BASS => TREBL => SUBWF. After selecting the desired parameter, you can adjust the current level by pressing VOL+/- buttons on the RC or on the unit.
System setup When the unit is on, the Main menu will be displayed. Press SETUP button on the RC or press and hold MENU/SEL button on the unit, or touch SET item on the monitor to enter the System setup menu. System setup menu includes VIDEO, AUDIO, SOURCE and SYSTEM items. Touch them on the monitor to set the desired status. Video adjust In this menu you can adjust CONTRAST, COLOR, TINT, BRIGHT, PICTURE (sharpness).
System adjust In this menu you can adjust a number of general system operation parameters. Touch an item on the screen to get the option menu, and then select the needed option by touching it on the screen. Touch arrow buttons at the right side of the screen to display the next or previous menu page. Clock System: Set 12-hour or 24-hour clock display mode. Key Beep: Select ON or OFF, the default setting is ON. It means when you press the buttons, they are sounded. Monitor Flex: not adjustable.
Radio operations User interface of Radio mode When the unit is switched to Radio mode, the following touchable user interface will be displayed on the display: 1. Band indicator. Shows which band the radio is tuned to. 2. AMS button. Briefly touch to scan the current station. Touch and hold to tune automatically. 3. BAND button. To select bands. 4. Preset number indicator. Shows what preset is selected. 5. Frequency indicator. Shows which frequency the tuner is tuned to. 6.
Local/distant selector In radio mode, press LOC/SUB-T button on the RC to select strong or weak station reception. LOC appears on the display and only local stations are available. When you turn it off both distance and local stations can be received. Note: The function is invalid in AM bands. Selecting stored station In radio mode, press NEXT/PREVIOUS buttons on the RC to select the stored station upward/downward.
Goto FREQ Press GOTO button, and the monitor shows FREQ. Then press number buttons to input the needed frequency. The unit will go to the input frequency. Note: this function is only available when GOTO FREQ is set to ON in System adjustment menu. RDS background RDS service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available. RDS touchable user interface 1.
TA (Traffic alarm) function Briefly press TA/LOUD button to activate the traffic alarm function. When AF is on, the TA displays on TFT, or else, if there is no TP information, the mode will search TP station automatically. The TA is green when it is played by a station, if not, it is yellow. When TA is playing, the volume will be adjusted to a TA level automatically. When other modes are activated (such as DVD, AUX), if a TA program is played the mode will skip to the RDS mode automatically.
TV-tuner operations TV touch screen menu When you select TV mode, following touchable User Interface will be displayed: 1. Preset station number. 2. Digit buttons. To select a channel numbered 1 to 9, touch the number on the monitor to select. Press -- at first, then press the corresponding number button to select a channel number more than 10. 3. Current TV frequency. 4. STEP button. Touch to adjust clearer image. 5. ANT button. Touch it to select the left or right antenna. 6. SET button.
Frequency searching Press REWIND/FORWARD buttons on the RC to select the frequency upwards and downwards step by step. Press and hold the button for automatic search of channels. Seek channels automatically Press AMS/MENU button on the RC to seek stations automatically. AUX operations When AUX mode is selected, following User Interface will be displayed: Touch AV SET item to go to AUX setup menu. In this menu you can adjust following parameters: 1. AUDIO ADJUST 2. VIDEO ADJUST 3.
Disc/USB/SD operations Insert/eject disc Press REL button on the panel or EJECT button on the RC to open the front panel. Insert a disc into the slot. The unit will automatically switch into DVD mode. After loading, its playback will start automatically. Open the front panel and press EJECT button to eject the disc. Touch screen operations with DVD/VCD/MP4 discs While playing a DVD/VCD/MP4–disc, the touch screen has following areas enabling to perform various playback operations: 1.
Touch screen operations with CD/MP3/USB/SD While playing a file contained on a CD/MP3/USB/SD, the touch screen has following areas and buttons enabling to perform various playback operations: 1. Disc/File type indicator (not operable) 2. File list. Touch the needed file to start its playback 3. Track area – touch to call digit keyboard. Touch digit buttons to input the number of a track to be played 4. List scroll buttons 5. PLAY/PAUSE button 6. STOP button 7. CARD/USB indicator (not operable) 8.
For correct and satisfactory operation, licensed SD/MMC memory cards of famous brands should be used with this unit. Avoid using memory cards of unknown brands. Capacity: up to 4 Gb. Selecting tracks For DVD/MP3: Press PREVIOUS/NEXT buttons on the RC to skip to the previous or next chapter. For VCD/CD: Press PREVIOUS button on the RC to skip to the beginning of the current chapter. Press and hold PREVIOUS button to skip to the previous chapter. Press NEXT button on the RC to skip to the next chapter.
Slow playback Press repeatedly SLOW button on the RC for slow forward or backward playback in the following order: For DVD: 1/2 forward => 1/4 forward => 1/8 forward => 1/2 backward => 1/4 backward => 1/8 backward => Normal. For VCD: 1/2 forward => 1/4 forward => 1/8 forward => Normal. Picture zooming Press ZOOM button on the RC repeatedly to increase the picture scale in the following order: 2X => 3X => 4X => Normal.
Audio language Press ST/AUDIO button repeatedly to switch between available audio languages (for DVD) or audio channels (for VCD) during playback. Subtitle language Press repeatedly LOC/SUB-T button during playback to switch between subtitle languages. This function is only valid with DVDs featuring multi-subtitle recordings. Playback programming Press PROG button to display the program menu. Then press number buttons to input numbers of tracks/chapter (depending on the disc type) in the order you need.
DVD Setup menu 1. Press SETUP button on the RC to enter the setup menu. 2. Use LEFT/RIGHT cursor buttons to choose the setup page: General page, Dolby Digital setup, Preference page, Exit. 3. Press DOWN cursor button to enter the setup page selected. 4. Use LEFT/RIGHT cursor buttons to select the option you want to adjust. 5. Press RIGHT cursor button to enter the adjustment list. Use UP/DOWN cursor buttons to select the adjustment and press ENTER/PLAY button to confirm. 6.
If the Screen saver is set On and the unit is switched on without a disc playing for 3 minutes, a moving picture appears on the TFT. Dolby digital setup DUAL MONO Choose the mode of the audio output: Stereo: choose this setting, when 5.1-channel sound playing, two channels of signals will be output from the left and right soundtrack; when 2-channel sound playing, stereo signal will be output. L. Mono: the signal will be output from the left speaker. R. Mono: the signal will be output from the right speaker.
PARENTAL The control level is for parental to control playing content and protect your children from violence and erotic. The disc, the level of which is higher than the setting level can not be played. Set the control level: (1) with the least limits when playing. (8) with the most limits when playing. Original setting: OFF. Note: The rating can be selected only under the Password unlocked status, and the limits can be worked only under the password locked status.
Handling and cleaning discs Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not touch its surface. Discs should be stored in their cases after use to avoid scratches. Do not expose discs to direct sunlight, high humidity, high temperature or dust. Prolonged exposure to extreme temperature can wrap the disc (such as leaving the discs in your car during summertime). Do not stick or write anything on either side of disc.
Troubleshooting guide Below is a table describing simple measures that can help you eliminate most problems likely to emerge when this unit is in use. If below measures do not help, turn to a service center or to the nearest dealer. Symptom Cause Solution No power The car ignition is not on. If the power supply is properly connected to the car accessory switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Volume is on minimum. Adjust volume to a desired level.
defective. Temperature inside the car is too high. Cool off until the ambient temperature returns to normal. The built-in microcomputer is not operating properly. Reset the unit with the help of RESET button. Front panel is not properly fix into its place. Install the front panel properly. The radio does not work The antenna cable is not connected. Insert the antenna cable properly. The radio station automatic tuning does not work The signals are too weak. Select stations manually.
Specification General Power supply: Maximum power output: Compatible disk types: Compatible formats: Dimensions/weight: ESP function: TFT display Screen size: Resolution: Aspect ratio: Contrast ratio: Brightness: View angle: FM Stereo Radio Frequency range: Usable sensitivity: Preset memory stations: AM Radio Frequency range: Preset memory stations: TV Tuner Color System: Tuning Range: 14 V DC 4 x 50 W DVD/DVD±R/DVD±RW/CD/CD-R/CD-RW/USB/SD/MMC DVD/SVCD/VCD/HDCD/MP3/WMA/CDDA/Picture-CD/JPEG/MPEG4(DivX) D x
! . . , ....................................................................................................35 ...................................................................................36 ..........................................................................................37 ...................................................................................38 ......................................................................................43 .............................................
, . . , . 1 1. , , . . . . . , , . . , . . . 20 . , , . . , . , , . , . , .
. . , , . , , , , , . . , . . 1. 2. 3. 4. 5. USB- ISO- : M5x5 M5x20 6. 7. 8.
1: « 1. » 2. . 3. 4. . . . . , 2: , . , .
1. 2. . ) . , , 39 , .
ISO 1. ISO, . 2. , , ISO . , . A 1 2 3 4 5 6 7 8 - . . . . . . +12 .- . - . . . : . 41 . . . B (+) (-) (+) (-) (+) (-) (+) (-) - .
, , . “Attention! You cannot use this function while driving” (“ “), . ( ) , . .
1. 2. 3. 4. TFT5. 6. 7. 8. 9. VOL+/PWR/SRC MENU/SEL 1. 2. 3.
( 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. ) AF/EQ PWR/SOURCE GOTO BAND/TITLE AMS/MENU LOC/SUB-T ST/AUDIO PTY/ANGLE OSD ZOOM SLOW P/N PROG MUTE VOLTA/LOUD EJECT NEXT CLEAR REWIND FORWARD ENTER/PLAY button SETUP PREVIOUS STOP PAUSE RDM 29. 30. 31.
1. 2. , (CR 2025 3V), . . . : . , . ( 6 – ). . . .
, . , RES ( . , ); . : RES . PWR/SOURCE PWR/SRC , . . REL EJECT , . . : ; . ANGLE (« »). MUTE/- , 46 BAND/+ REL . .
MUTE/- . . VOL+/VOL- +/- . SEL : VOL ( MENU/SEL ) => BALAN ( , ) => FADE ) => TREBL ( VOL+/VOL- ) => BASS ( ) => SUBWF ( +/- ). , . MUTE/- MUTE . . . AF/EQ , . : POP => CLAS => ROCK => OFF ( TA/LOUD .). – OFF. , . 47 .
. : : PWR/SOURCE => => SRC . , . , => USB PWR/SRC => AUX => USB. . , , . CLEAR 48 .
. SETUP MENU/SEL , SET . VIDEO, AUDIO, SOURCE SYSTEM. . (VIDEO) (CONTRAST), (TINT), (BRIGHT) (COLOR), (PICTURE). , , . . , SAVE. , RESET. EXIT. (AUDIO) (VOLUME), (BALANCE), (SUBWOOF), (fader), (BASS), (TREBLE). , , . . EXIT.
(SOURCE) TV ( . (ON) ), NAVI ), BT, SD ( BT (OFF) : AUX, USB. NAVI . (SYSTEM) . , . CLOCK SYS ( KEY BEEP ( . 12(ON) ): ): 24- . (OFF) , . MONI FLEX REVER POLA ( . ): . LAMP SEL ( +12 V, GROUND (OFF) 0 V, (ON) ): . BATTERY . . AMS FULLUP ( ON ( . LOCAL AREA ( LOCAL ( ON ( OFF ( GOTO FREQ ( AMS): AMS. ) OFF ( ): . ) . OIRT EUROPE, USA ): ) ) ; ; ): ON ( . GOTO ), .
RT Scroll ( ): ), NORMAL ( : SLOW ( TA Volume ( ) HIGH ( Region ( ): ADJ SCREEN ( RDS) FAST ( ). ): ). : LOW ( AF, ON ( ). ): : “Please press the button” (« . , , . , »). ; , . (« ), NORMAL “Adjust successful” »). . CLOCK ADJ ( ): , . . , , , 51 .
, 1. 2. : . AMS. . . 3. 4. 5. 6. BAND. . . . 6 . . , 7. 8. 9. . RDS. SRC. SEEK+/-. . . RDS. . . BAND/TITLE BAND/+ : FM1 - FM2 - FM3 – FM4 - AM1 - AM2. : REWIND/FORWARD .
: REWIND/FORWARD , . LOC/SUB-T , , . LOC; . , . : AM. , NEXT/PREVIOUS . ST/AUDIO . MONO. , . . : FM. AMS/MENU AMS , , , . ; (1 – 6). AMS AMS/MENU . 2 AMS/MENU . (1 – 6).
2 . : 6 . OSD . GOTO, FREQ. . : , . GOTO FREQ , (ON) . RDS RDS ( ) RDS . , RDS 1. PTY (ON), . 2. (OFF). 3. PTY. (ON) . . 4. (OFF) 5. (OFF) 6. . (ON)/ . AF. , . (ON)/ AF. SEEK+/-. .
7. BACK: . AF/EQ AF. , , . . : RDS AF , , RDS. AF. TA (Traffic Alarm) TA/LOUD . TP. «TA» Traffic alarm. , TP AF, «TA» ; . TA , . ( RDS. ., DVD, AUX), TA, , . PTY/ANGLE PTY, PTY. PTY ON; . PTY , PTY SEARCH. PTY OFF, 55 .
: 1. 2. . 1 . 9 . --, 10. 3. 4. . STEP. . 5. ANT. . 6. SET. SOUND ( ). BAND ( ). MODE ( ). MANU+/MANU-: AUTO: 7. CH-/CH+. 8. : , : M/N, B/G, D/K. V-l, V-H, UHF. : SECAM/NTSC/PAL. . . . . , . .
9 PREVIOUS/NEXT 1-9 GOTO . . . , REWIND/FORWARD . . AMS/MENU . AUX AUX : AV SET AUX. : 1. AUDIO ADJUST ( 2. VIDEO ADJUST ( 3. VIDEO FORMAT ( SECAM; Auto 2 – P-M, P-N).
/USBREL EJECT RC, . . DVD. . EJECT, . DVD/ VCD/MP4 DVD/VCD/MP4, : 1. ( )/ )– . 2. – . .
DVD CD/MP3/USB/SD , CD/MP3/USB- SD, : 1. 2. ( ) . . 3. – . . 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. PLAY/PAUSE ( STOP ( ) CARD ( PREVIOUS ( SEL. NEXT ( +/-. ) )/USB ( ) ) , . ) . DVD.
USBUSB- USB . USB USB- . , USB- USB. . . . , , , . : USB: : 4 . SD/MMC: . . DVD/MP3: VCD/CD: PREVIOUS/NEXT PREVIOUS 4 . . PREVIOUS . PAUSE STOP : . . NEXT . , . ENTER/PLAY PAUSE , CD/MP3). ( STOP . . REWIND/FORWARD / . : 2X => 4X => 8X => 16X => 60 .
RPT DVD: => VCD/MP4/CD/MP3: : => . => . RDM . . P/N : PAL, NTSC . SLOW . DVD: 1/2 VCD: 1/2 3X => 4X => => 1/4 => 1/4 => 1/8 => 1/8 => 1/2 => . => 1/4 => 1/8 : . => ZOOM . : 2X => OSD . DVD: ) . GOTO ( .). ENTER 61 .
. . VCD/CD: , GOTO “ “ :--:--”. . GOTO MP3: . GOTO :--:--”. . . GOTO , . “---”. GOTO “--:--”. , . . DVD PTY/ANGLE , . , . ST/AUDIO ) ( ( DVD, VCD). DVD LOC/SUB-T , . PROG . . ( ) 62 . ENTER/PLAY. ENTER/PLAY.
START . . ENTER/PLAY ENTER/PLAY ID3MP3 ID3 Tag, . ( 1. ENTER/PLAY 2. DVD) AMS/MENU . ; . BAND/TITLE . ENTER/PLAY .
DVD 1. 2. DOLBY, 3. 4. 5. SETUP , . : , , . . , . . ENTER/PLAY . 6. 7. . SETUP 4:3 , PS: 4:3 , LB: . , . , . : , . DVD – , . , DVD , .
. , . - , . , , . DOLBY : .c : , 5,1- , . . .: .: : OFF ( . . . FULL .) . . . , , 65 .
PAL: NTSC: : , , , , . . , . , , . , . , . ST/AUDIO LOC/SUB-T . , , , , : - . . . , . « 8888), – , . . 1 8 , . , », ( ENTER.
, ». 8888 ( ), , (4 . (8888) ENTER, . . . , . 67 ).
, . , . , , . , . ( , ). . , , . . . . ( . ), . , , . . , , . .
, , , . , . . . ”. . . . . . 35 , “ . 35 , . . . . , . . .
. . . . , . . . RESET. . . . .
( )/ 14 50 4 DVD/DVD±R/DVD±RW/CD/CD-R/CD-RW/USB/SD/MMC DVD/SVCD/VCD/HDCD/MP3/WMA/CDDA/PictureCD/JPEG/MPEG4(DivX) 170 178 100 /3,4 40 CD, 120 3 7 480 234 16:9 300:1 2 350 0 120 , : 1200 FM 65 10 24 – 74 /87,5 – 108 AM 522 – 1710 12 SECAM/NTSC/PAL 48,25 – 863,25 . .
