User Manual
Table Of Contents
- 1. 1. INTRODUCTION
- 2. OVERVIEW
- 3. MAIN FEATURES
- 4. OVERVIEW
- 5. OPERATION GUIDE
- 6. OPERATION
- 7. PROGRAMMING
- 8. CHASE PROGRAMMING
- 9. SCENE PROGRAMMING (Steps)
- 10. PLAYBACK
- 11. MIDI OPERATION
- 12. APPENDIX
- 13. SPECIFICATIONS
- 14. WARRANTY AND SERVICE
- 15. WARNING
- 1. INTRODUZIONE
- 2. PANORAMICA
- 3. CARATTERISTICHE PRINCIPALI
- 4. INTRODUZIONE
- 5. GUIDA OPERATIVA
- 6. GUIDA OPERATIVA
- 7. PROGRAMMAZIONE
- 8. PROGRAMMAZIONE DI UNA CHASE
- 9. PROGRAMMAZIONE DELLE SCENE
- 10. PLAYBACK
- 11. UTILIZZO DEL MIDI
- 12. APPENDICE
- 13. SPECIFICHE
- 14. GARANZIA E ASSISTENZA
- 15. AVVISO
11. MIDI OPERATION
SCENEMAKER 1216 only responds to MIDI commands on the MIDI channel which is set
to full stop. All MIDI controls are performed using Note on commands. All other MIDI
instructions are ignored. To stop a chase, send the blackout on note.
1. Press and hold MIDI/Add button for about 3 seconds.
2. Select the MIDI control channel (1-16) via the BANK UP/DOWN buttons.
NOTE: This is the Channel that the controller will receive MIDI note com-
mands.
3. Press and hold the MIDI/Add button for 3 seconds to save settings.
MIDI NOTE FUNCTION (TURN ON/OFF) MIDI NOTE FUNCTION (TURN ON/OFF)
00 to 07 Scenes 1~8 in BANK 1 88 to 95 Scenes 1~8 in BANK 12
08 to 15 Scenes 1~8 in BANK 2 96 to 103 Scenes 1~8 in BANK 13
16 to 23 Scenes 1~8 in BANK 3 104 to 111 Scenes 1~8 in BANK 14
24 to 31 Scenes 1~8 in BANK 4 112 to 119 Scenes 1~8 in BANK 15
32 to 39 Scenes 1~8 in BANK 5 120 Chase 1
40 to 47 Scenes 1~8 in BANK 6 121 Chase 2
48 to 55 Scenes 1~8 in BANK 7 122 Chase 3
56 to 63 Scenes 1~8 in BANK 8 123 Chase 4
64 to 71 Scenes 1~8 in BANK 9 124 Chase 5
72 to 79 Scenes 1~8 in BANK 10 125 Chase 6
80 to 87 Scenes 1~8 in BANK 11 126 BLACKOUT
12. APPENDIX
12.1. DMX Introduction
There are 512 channels in a DMX-512 connection. Channels may be assigned in any
manner. A xture capable of receiving DMX 512 will require one or a number of se-
quential channels. The user must assign a starting address on the xture that indicates
the rst channel reserved in the controller. There are many different types of DMX con-
trollable xtures and they all may vary in the total number of channels required.
Choosing a start address should be planned in advance. Channels should never overlap.
If they do, this will result in erratic operation of the xtures whose starting address is
set incorrectly. You can however, control multiple xtures of the same type using the
same starting address as long as the intended result is that of unison movement or
operation. In other words, the xtures will be slaved together and all respond exactly
the same.
21
ENGLISH
SCENEMAKER 1216 User manual










