CA 160 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a Digital Multi Meter for testing and verifying circuits.
BLUE/GREEN (-) 2ND STAGE UNLOCK NEGATIVE LOCK/POSITIVE UNLOCK NEGATIVE UNLOCK/POSITIVE LOCK GREEN BLUE CA-160 SYSTEM LAYOUT (+) IGNITION 1 INPUT/OUTPUT PINK (+) STARTER OUTPUT(MOTOR SIDE) PURPLE (+) STARTER INPUT(KEY SIDE) GREEN (+) 12 VOLTS BATTERY RED 30 AMP UNLOCK SENSE INPUT TRUNK PIN INPUT(-) Lt BLUE/GREEN BLUE BLUE/WHITE WHITE/BLUE 3 4 5 6 DOME LIGHT OUTPUT NEGATIVE DOOR TRIGGER GROUND MANUAL DISARM INPUT OPEN POSITIVE DOOR TRIGGER UNUSED HEADLIGHT OUTPUT (-) SONGBIRD OUTPUT (-) BLACK BR
CA- 160 System Layout 4-Pin Tracking Port 4-Pin Auxilliary Port (Green]) (White) 4-Pin Receiver Port (Black) 2-Pin LED Port (White) 4-Pin External Sensor Port (Tan) 22-Pin Base Harness 2-Pin Valet Port (Blue) 22 Pin Base Harness 4 Pin Auxiliary Harness (GREEN) 1 C H AN N EL 2 PIN K /B LAC K 1 DOME LIGHT OUTPUT BLACK/WHITE 2 C H AN N EL 3 PIN K /GR EEN 2 MANUAL ARM INPUT LT.
-Pin Power Harness 3-Pin Door Lock Port (White) 4 Pin Power Harness 1 + 12 VOLTS STAR TER IN PU T 2 (K eyside) STAR TER OU TPU T(Motor Side) 1 N EG LOC K /POS U N LOC K GR EEN GR EEN 2 N EG U N LOC K /POS LOC K B LU E 3 2N D STAGE U N LOC K B LU E/GR EEN P U R P LE 4 IGN 1 Input/Output PIN K Fuse Grid + - Parking Light Polarity Dome Polarity - + Trunk Polarity 3 3 Pin Door Lock Harness R ED + Recommend 15Amp
Programming Options RF Programmer The RF Programmer allows you to customize the system to fit the individual needs of the consumer, using a handheld device capable of transmitting system settings directly to the system control module. The RF Programmer is broken down into three different programming banks. 1. RF Programmer Bank- The RF Programmer Bank allows you to set up the base features of the system you are installing.
RF Programmer Selecting Programmable Features 1. Press the POWER button to turn the system ON. 2. Once powered up the MENU screen will be displayed. 3. Use the UP & DN arrows to scroll through the programmable features. Once you locate the desired feature to change, press the > arrow to advance to the next screen. You should see the default setting of the system 4. Press the SET button to scroll through the available settings.
CA 160 Programming Guide Feature Bank 0 - 3 Chirps Transmitter Programming Feature Bank 1 - 4 Chirps RF Programmer Receive Bank Feature Bank 2 - 5 Chirps Lite Touch Adjustment Full Trigger Adjustment Feature Bank 3 - 6 Chirps Shock Sensor Programming (W/Transmitter Only) Lock increases sensitivity, Unlock decreases sensitivity Lock increases sensitivity, Unlock decreases sensitivity 1 LED Flash 2 LED Flashes 3 LED Flashes 4 LED Flashes 1 Second 3.
1. SETUP & PROGRAMMING Transmitter Programming (3 Chirps) 1. With the door open turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 Seconds the system will chirp (3) three Times. 4. Press any one button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. Pressing the override button at anytime during programming will advance to the next bank.
1. 4 PIN MAIN POWER HARNESS Battery Power (RED) Locate the vehicle’s battery wire(s) at the ignition switch. Verification: These wires will register voltage in all positions of the ignition switch. Connect the RED wire to the vehicle’s battery wire. Note: Remove all 30 Amp fuses until all connections are made. 12 volts Ignition Input/Output (PINK) Locate the vehicle’s Ignition wire at the ignition switch. Verification: This wire registers voltage when the key is turned to the ON (or RUN) position.
2. BASIC INSTALLATION - 22 PIN BASE HARNESS Dome Light Supervision Output (+/-) (BLACK/WHITE) Locate the vehicle’s dome light or pin switch wire. Verification: This wire will register positive voltage or ground when the vehicle's dome is turned ON. Typically this wire is installed with the door trigger input wire. Refer to NEG/POS door input for reference. To select Negative or Positive polarity output: Refer to Fuse Placement Diagram below.
2. 22 PIN BASE HARNESS CONTINUED Ground When Armed Output (ORANGE) This wire will show ground when the system is armed. This wire is used for controlling window modules or additional sensors. Headlight Output (LT. GREEN/ORANGE) Locate the vehicle’s headlight wire. Verification: This wire will register either positive voltage or ground when the headlights are turned on. Connect the LT. GREEN/ORANGE to the vehicles headlight wire if the system is negative. (LOW CURRENT ONLY).
2. 22 PIN BASE HARNESS CONTINUED Instant Trigger Input (BLUE/WHITE) This wire is a GROUND input for an external sensor or secondary pin switch Verification: This wire when connected will trigger the security system Siren Output (+) (BROWN) Locate a suitable mounting location in the engine compartment for the siren, away from moving parts. With the bell of the siren aiming downwards, secure the siren in place using self tapping screws, being careful not do drill into any hoses, wiring or components.
2. 22 PIN BASE HARNESS CONTINUED Manual ARM input (LT. BLUE/RED) This wire will ARM the security system when a POS or NEG pulse is applied to it from an external device. Manual DISARM Input (LT. BLUE/BLACK) This wire will DISARM the security system when a POS or NEG pulse is applied to it from an external device. Unlock Switch Sense (LT. BLUE/GREEN) This wire will prevent the system from disarming the security system when a POS or NEG pulse is applied to it from an external device.
3. 4 PIN ADVANCE CHANNEL HARNESS Channel 2 (PINK/BLACK) This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof,etc.). To Activate press and hold LOCK & TRUNK. Please refer to the selectable options for timing. Selectable timing: Push & Hold/10 Seconds/20 Seconds/Press to Latch ON/Press to Latch OFF. Channel 3 (PINK/GREEN) This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories (i.
4. DOOR LOCKS Negative Lock Output / Positive Unlock Output (GREEN) Negative Unlock Output / Positive Lock Output (BLUE) Negative Second Door Unlock Output (BLUE/GREEN) The door lock / unlock outputs are designed to control several different types of systems which may require additional parts. Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the diagrams below.
4. DOOR LOCKS Negative Lock Output / Positive Unlock Output (GREEN) Negative Unlock Output / Positive Lock Output (BLUE) Negative Second Door Unlock Output (BLUE/GREEN) Positive Switching and Positive Switching with 2-step unlock feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will register positive voltage when the Lock and Unlock switches are activated.
4. DOOR LOCKS Negative Lock Output / Positive Unlock Output (GREEN) Negative Unlock Output / Positive Lock Output (BLUE) Negative Second Door Unlock Output (BLUE/GREEN) Reverse Polarity (5-Wire Doorlocks) and Reverse Polarity with 2-step Unlock: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will rest at ground and register positive voltage when the Lock and Unlock switches are activated.
4. DOOR LOCKS Negative Lock Output / Positive Unlock Output (GREEN) Negative Unlock Output / Positive Lock Output (BLUE) Negative Second Door Unlock Output (BLUE/GREEN) One Wire Negative Multiplexed and One Wire Negative Multiplexed with 2-step Unlock Feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable ground when the switch is activated.
4. DOOR LOCKS Negative Lock Output / Positive Unlock Output (GREEN) Negative Unlock Output / Positive Lock Output (BLUE) Negative Second Door Unlock Output (BLUE/GREEN) One Wire Positive Multiplexed and One Wire Multiplexed With 2-step Unlock Feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable positive voltage when the switch is activated.
4. DOOR LOCKS Negative Lock Output / Positive Unlock Output (GREEN) Negative Unlock Output / Positive Lock Output (BLUE) Negative Second Door Unlock Output (BLUE/GREEN) Adding Aftermarket Actuators: After installing aftermarket actuators, Code Alarm part DA-1 (not supplied). Connect the GREEN and BLUE wires shown in diagram 16 below. Use (1) Code Alarm part DLRK (Door Lock Relay Kit, not included) or (2) Code Alarm part HDRLY (SPDT relay, not included).
5. ACCESSORY CONNECTOR'S 2 Pin Valet/Program/Override Push-Button Switch: (Blue Connector) The BLACK and GREY twin lead wires loaded in the two pin blue connector are the ground supply and program/valet/override input of the Remote Start. Drill a 9/32" hole and mount this switch in an easily accessible location under the driver's dashboard.
7. System Testing 1. Follow each instruction below. 2. Verify that the system operates as indicated under each instruction. Refer to the system owners manual. 3. Check the appropriate wire connection(s) and/or fuse(s) if the unit fails to perform a specific function. Also check that any options pertaining to the function are programmed properly. Security Operation Press LOCK once: 1. Doors lock. 2. Courtesy lights (if on) shut off. 3. Unit checks to see if doors, hood or trunk are open.
7. System Testing Cont. Press DISARM: 1. Doors unlock. 2. Factory alarm (if equipped) is turned off. 3. Siren/horn sounds once/ parking lights flash once. 4. Courtesy lights turn on for 30 seconds, or until ARM is pressed or ignition is turned on. 5. Vehicle starter is enabled. . Press DISARM twice: 1. Passenger doors unlock if using 2-stage unlock. Press FIND: Siren/horn sounds 5 times.