T E C H N O L O G I E S Owner’s Manual and Installation Guide RUB1.1000D RUB1.1600D RUB1.
CONGRATULATIONS! You now own a Limited Edition RUBICON Amplifier, the product of an uncompromising design and engineering philosophy. To maximize the performance of your system, we recommend that you thoroughly acquaint yourself with its capabilities and features. Please retain this manual and you sales receipt for future reference. Soundstream amplifiers are the result of American innovation and the highest quality control standards.
FEATURES Total Harmonic Distortion:0.
SPECIFICATIONS >105dB 15Hz-150Hz 0.50% 50Hz -150Hz,12dB 11-16 Volts DC Signal/Noise Ratio Frequency Response THD LPF Input Voltage Range High Impedance RCA/LINE Level Input Impedance 30K Ohms POWER RATINGS & FUSE MODEL 4 ohm 2 ohm 1 ohm FUSE RUB1.1000D 600W 800W 1000W 35A X 3 RUB1.1600D 700W 1100W 1600W 40A X 4 RUB1.2500D 1000W 1700W 2500W 250A DIMENSIONS MODEL Length Width Height RUB1.1000D 390mm 205mm 60mm RUB1.1600D 450mm 205mm 60mm RUB1.
TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED Small flat blade screwdriver phillips screwdriver (#2 or medium sized), Wire cutters, Wire strippers, - #6 round head screws, and 1 - #8 sheet metal screw (or nut, bolt flat washer, start washer) (see detail) 2 Ring connectors (large enough to accommodate your method of grounding) In-line fuse or Grommets (Sized to work with the power wire you plan to use in your installation) Tube of silicone seal.
Electrical Wiring All RUBICON Amplifiers are equipped with easy top access screw terminals . These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following : Use at least 4 gauge or heavier wire for power and ground connections. Wire the amplifier directly to the car battery.
PANEL LAYOUT RUB1.1000D LEFT VIEW L Line Out Line Input L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz .1V-2V R 0 Bridged Mode Input Sensitivity R 150Hz Bass Boost 2V-8V +18dB PHASE 0 REMOTE CONTROL DATALINK Master PROTECTION 180 Slave RIGHT VIEW BATT+ SPEAKER REMOTE GND POWER CONNECTIONS FUSES RUB1.1600D LEFT VIEW L Line Out Line Input L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz Input Sensitivity R R .
PANEL LAYOUT RUB1.2500D LEFT VIEW L Line Out Line Input Subsonic Filter Input Level L Min Max 10Hz Low Pass Filter 40Hz 50Hz .1V-2V R 150Hz 0 Bridged Mode Input Sensitivity R Bass Boost 2V-8V +18dB PHASE 0 REMOTE CONTROL DATALINK Master PROTECTION 180 Slave RIGHT VIEW SPEAKER POWER CONNECTIONS Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D/RUB1.
Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D BATT+ SPEAKER FUSES REMOTE GND POWER CONNECTIONS RUB1.1600D has four fuses here BATT+ SPEAKER FUSES RUB1.
Class D Monoblock Amplifier Installation Wiring RUB1.
Bridging Two RUB1.1000D/RUB1.1600D/RUB1.2500D Amplifiers L Line Out Line Input L L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz R .1V-2V R 0 Bridged Mode Input Sensitivity R 150Hz Bass Boost 2V-8V +18dB PHASE 0 REMOTE CONTROL DATALINK Master PROTECTION 180 Slave Power min L Line Out Line Input L Subsonic Filter Input Level Min Max 10Hz Low Pass Filter 40Hz 50Hz Input Sensitivity R R .
Bridging Two RUB1.1000D/RUB1.1600D Amplifiers BATT+ SPEAKER REMOTE GND POWER CONNECTIONS FUSES RUB1.
Bridging Two RUB1.
TROUBLE SHOOTING NO SOUND Is the LED lit? NO YES Check Power and Remote turn-on wire for voltage. Make sure Ground wire is secure. STILL NO SOUND See your Authorize Sound Stream Dealer. SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector. turning it over and plugging it back in.
Caution: Please do not plug in or unplug RCA Plugs to the amplifier inputs while the amplifier is turned on. Doing so is potentially harmful to the amplifier by allowing RF(radio frequencies) into the amplifier, causing instability, during the brief period while the RCA shield is not connected, and the hot is connected. Only plug in or unplug RCA plugs with the amplifier off as Standard practice with all audio equipment.