Features • • • • • • • • • • • • • • Class-D Digital Full range 2ohm stable stereo. Applying new concept .. Low-Heat Producing Circuit ... Tri-mode capable. Channel Design 3 /2 Channels. Full MOSFET DC-DC PWM Power Supply. Four way protection. " "" 0 @ ©©"'".~§ Double Sided FR-4 PC Board. p SMD Technology. High level input connector (Auto turo ON}. ~ @~~~~ Crossover: Adjustable Low-Pass,Hi-pass, Bass boost. Nl Plated RCA Input Connectors.
Features PN1.450D • • • • • • • • • • • • • • PN1.650D Class-D Mono block 2ohm stable. Applying new concept .. Low-Heat Producing Circuit ... Channel Design 1 Channel. (Mono) Full MOSFET DC-DC PWM Power Supply. Four way protection. Double Sided FR-4 PC Board. SMD Technology. @ @ High level input connector. Variable low pass remote dashes mount gain control. /[~ ~]r;lQ[~~ ~ll Nl Plated RCA Input Connectors. 0 @ $ @ ~ ~ Adjustable Low-Pass, Bass boost, Sub sonic. Adjustable Gain Control.
Power Connections It is important to have good quality power and ground connections. Remember, to complete an electrical circuit, the ground connection is just as important as the positive power connection. Before any power connections are made, disconnect the ground cable of the battery. Use 8 gauge or larger automotive grade wire if the distance from the battery to the amp is excessive. Avoid sharp or rough edges as a safeguard against short circuiting and potential fire hazards.
Speaker out connection. BRIDGED MODE STEREO MODE MODEL NO.: PN2.350D. Speaker out connection. 4n- &l 4n- &l ,,rnpL ~ R STEREO MODE ~(:)--- --8-R-ID_G_E_D__,MODE L R MODEL NO.: PN4.320D. PN4.520D. Speaker out connection. BRIDGED MODE MODEL NO.: PN 5.640D. Speaker out connection. n @ ) ~ @ SPEAKER OUT [~~@~~i'!' 1 G FUSE POWER BB[i!j) 12V DC @ REM GND ,~ I ( @ 2Il-&l ~Ill . I~ a 4 MODEL NO.: PN1.450D. PN1.650D.
PICASSO NANO PRE-AMP FEATURES 1. Remote Level Control Connection 6. RCA Audio Input Connection Connect the remote level control to this terminal. The remote level control allows adjustment of the subwoofer level from a remote location in the vehicle. Using high quality shielded stereo RCA cables, connect the source signal to the amplifier RCA inputs. 2. Low Pass Crossover Adjust the frequency setting of the low pass crossover. The frequency range is 35Hz-250Hz.
Mounting Your Picasso Nano Choosing the best mounting location for your Picasso Nano amplifier is crucial. The amplifier should be mounted to any wood, metal, or carpeted surface. The heatsink can be mounted directly to the chassis of the car, or isolated for best performance. It needs proper ventilation, so avoid mounting the amp under seats, in the engine bay, or any other area that moisture might accumulate.
Setting the gains: It is a fact that very few people, including professional installers, know how to set gains correctly. Failure to do so yields higher distortion, a higher noise floor which decreases dynamic headroom, less than optimum operating conditions for electronic equipment, and higher failure rate for both the electronic equipment and transducers alike. While most people set this control by ear to how loud they want their music, this is not the intent of this control. The range is from 0.
Trouble shooting. SYMPTOMS Is the power LED illuminated? (NO) Check all fuses to amplifier. Be sure Turn-on lead is connected Check signal leads. Check gain control. Check Tuner/Deck volume level. Clean contacts on fuse holders. Is the Diagnostic LED illuminated? (YES) Check for speaker short or amplifier overheating. No power to power wire Repair power wire or connections. No power to remote wire with receiver on Check connections to radio.
LIMITED 90-DAY CONSUMER WARRANTY LIMITED TWO-YEAR CONSUMER WARRANTY WITH PURCHASE AND INSTALLATION BY A SOUNDSTREAM AUTHORIZED DEALER Soundstream promises to the original purchaser, to repair or replace this product with a new or refurbishedunit (at Soundstream's sole and absolute discretion) should it prove to be defective in workmanship or material under normal use, for a period of *two-years from the date of purchase from the Soundstream authorized dealer, PROVIDED the product was purchased and installe
Note: This warranty does not cover labor costs for the removal and reinstallation of the unit. IN ORDER FOR THE TWO-YEAR WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY A SOUNDSTREAM AUTHORIZED DEALER. ALL UNITS RECEIVED BY SOUNDSTREAM FOR WARRANTY REPAIR WITHOUT PROOF OF SOUNDSTREAM AUTHORIZED DEALER INSTALLATION AND PURCHASE WILL BE COVERED BY THE LIMITED 1 YEAR WARRANTY.
S@UNDSTREAM TECH N 0 L 0 G IE S Please Keep This Information For Your Records Product Model: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ Serial N u m b e r : - - - - - - - - - - - - - - - - - - - - - - - - - - - - Date P u r c h a s e d : - - - - - - - - - - - - - - - - - - - - - - - - - - - Name of Dealer: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ __ Dealer A d d r e s s : - - - - - - - - - - - - - - - - - - - - - - - - - - - - City: _ _ _ _ _ _ _ _ _ _ _ State: _ _ _ _ _ _ _
S@UNDSTREAM T E c H N 0 L 0 G E s SoundStream Technologies warrants this product to be free from defects in materials and workmanship under normal use and conditions, for a period of 1 year from the original date of purchase , if purchased and professionally installed by an Authorized SoundStream dealer. Any product purchased from and /or installed by others will be warranted for 90 days only.
WWW.SOUNDSTREAM.
rp;C.--
5Ch.
