>105 dB <0.05 % 0,2-6Volt >47 kOhm Signal-to-Noise Ratio THD&N Input Sensitivity Input Impedance 10.75" Dimensions 1 x 100A 13.5" 2x80A 15.75" 2x60A 11.75" ■ ■ ■ ■ ■ CCC ~00U, I\) > > U,0001\)1\) 000000 000000 ■ cncncncncncn (J1 > > ~ ~ I \ ) ::c ::c ::c ::c ::c ::c 0-12dB 13" 10.75" 30Hz-150Hz 50Hz -150Hz 50Hz-4KHz >47 kOhm 0,2-6Volt <0.
Table of Contents Installation Installation Installation Notes, Installation of Amplifier, Electrical Connections 2 2-Channel Amplifiers RS2.1200 Functions & Controls Speaker- & RCA Connections 3 4-5 4-Channel Amplifiers RS4.1200/RS4.2000 Functions & Controls Speaker- & RCA Connections 6 7-8 1-Channel Mono Bass Amplifier RS1 .5000D Functions & Controls Speaker- & RCA Connections 9 10-11 1-Channel Mono Bass Amplifier RS1 .
Functions & Controls !ipeaker & RCA Connections RS2.1200 RS2.1200 INTERCONNECTION EXAMPLE 2-Channel Mode: 1x Stereo System (Front or rear) HP PASS (HighPass) Controls the frequency response of your speakers downwards. The Cut-off frequency is continously variable from 50Hz up to 400Hz. RCA & Speaker wiring: • Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT at the amplifier with appropriate high-value RCA cables.
!ipeaker & RCA Connections Functions & Controls RS4.1200/RS4.2000 RS2.1200 INTERCONNECTION EXAMPLE 2-Channel Mode: 1x Mono Subwoofer bridged HP/LOW PASS CH1/2&CH3/4 HP PASS (High Pass) Controls the frequency response of your speakers downwards. The Cut-off frequency is continously variable from 50Hz up to 400Hz RCA & Speaker wiring: • Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
!ipeaker & RCA Connections !ipeaker & RCA Connections RS4.1200/RS4.2000 RS4.1200/RS4.2000 4-Channel-Mode: 2 Frontspeakers / Stereo & 2 Rearspeakers /Stereo 3-Channel-Mode: 2 Speakers/Stereo & 1 Subwoofer / Mono bridged Cable connection • Connect INPUT of the amplifier to the head unit line output with good quality RCA cables. By connecting the RCA jacks OUTPUT with a additional amplifier, a full range signal will be provided to the amplifier.
!ipeaker & RCA Connections Functions & Controls RS1 .50000 RS1 .50000 Low Pass This Controller adjusts the frequency response of your subwoofer upwards and is continously variable from 30Hz to 250Hz Sub Sonic This Controller eliminates the lowest frequencies to protect the subwoofer from damages. These low frequencies can cause damages. The frequency is adjustable from 20 Hz to 50 Hz.
Functions & Controls !ipeaker & RCA Connections RS1 .5000D RS1 .8000D MASTER/ SLAVE-MODE/ Subwoofer-Mode with two Ampifiers • • • • Connect the Connect the Connect the Connect the Low Pass This Controller adjusts the frequency response of your subwoofer upwards and is continously variable from 30Hz to 250Hz "LINE IN" (L & R) of the MASTER-amplifier to the head unit's line output with appropriate good quality RCA cables.
!ipeaker & RCA Connections !ipeaker & RCA Connections RS1 .8000D RS1 .8000D MASTER/ SLAVE-MODE/ Subwoofer-Mode with two Ampifiers RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. As optional feature the Balanced Inputs can be used. But therefor an signal transmitter with specific wires is required. Ask your specialist dealer for the required equipment.
!ipeaker & RCA Connections Functions & Controls RS5.4500D RS5.4500D INTERCONNECTION EXAMPLE 5-Channel Mode: 2x Stereo System (Front or rear)+1xSubwoofer HP PASS (HighPass) CH1/2 Controls the frequency response of your speakers downwards. The Cut-off frequency is continously variable from 10Hz up to 150Hz RCA & Speaker wiring: HP PASS (High Pass) CH3/4 Controls the frequency response of your speekers downwards.
!ipeaker & RCA Connections Troubleshooting RS5.4500D INTERCONNECTION EXAMPLE 3-Channel Mode: 1x Stereo System (bridged)+1xSubwoofer System does not turn on 1. Check all fuses. 2. Check all connections. 3. Measure the +12 volt and remote turn on voltages at the amplifier terminals. If these are non existent or low, take voltage measurements at fuse holders, distribution blocks, the head unit's +12 volt and remote leads to localize the problem. RCA & Speaker wiring: Noise problems 1.
