E s S E R V E UNDSTREAM OWI\IER'!i MAI\IUAL CAR AUDIO SYSTEM PLEASE READ CAREFULLY BEFORE INSTALLING OR OPERATED THIS UNIT WARNING Make sure you choose a suitable place to mount the unit. The position should be completely dry with a good circulation of air, and from a mechanical point of view very stable.
System Planning Proper system planning is the best way to maximize your amplifier performance. By planning your installation carefully you can avoid situations where the performance of the reliability of your system is compromised . Your authorized dealer has been trained to maximize your system's sonic potential. Your dealer is a valuable resource in helping you with your system design and installation.
Power Connection Leads Z DKd /EWhd Z ,/Ͳ/EWhd Z ' ' /E ^h ^KE/ >Kt W ^^ ^^ KK^d > Ϭ͘Ϯϱs ϲ͘Ϭs ϱϬ,nj ϭϬ,nj ϮϱϬ,nj ϯϬ,nj ϭϮĚ ϬĚ > 0 : IWBLCOMBI: 000000000 'E WKt Z /EWhd Z D нϭϮs ^W < Z KhdWhd + BATTERY Notes on the power supply Connect the + l 2V power input lead only after all other leads have been connected . Be sure to connect the ground wire of the unit securely to a metal part of the car.
System 1 connection subwoofer Wired Remote Control Z DKd /EWhd Z ,/Ͳ/EWhd Z ' ' /E ^h ^KE/ >Kt W ^^ ^^ KK^d > Ϭ͘Ϯϱs ϲ͘Ϭs ϱϬ,nj ϭϬ,nj ϮϱϬ,nj ϯϬ,nj ϭϮĚ ϬĚ > ~~~~~ o : 1WBlaCOMBI: 000000000 'E WKt Z /EWhd Z D нϭϮs ^W < Z KhdWhd + UWDYQQHGT ` • 3 •
System 2 connection subwoofer Wired Remote Control Z DKd /EWhd Z ,/Ͳ/EWhd Z ' ' /E ^h ^KE/ >Kt W ^^ ^^ KK^d > Ϭ͘Ϯϱs ϲ͘Ϭs ϱϬ,nj ϭϬ,nj ϮϱϬ,nj ϯϬ,nj ϭϮĚ ϬĚ > ~~~~ 0 : lwai.
Trouble Shooting Symptom no output Possible Cause Action to Take low or no remote turn-on input check remote turn-on voltage output at amplifier and correct as needed fuse blown check power wire integrity and reversed polarity ,repair as needed and replace fuse power wires not connected check power wire and ground connections and repair of replace as needed audio input not connected or no output from source check input connections and signal integrity, repair or replace as needed check speaker wir
Symptom Possible Cause Action to Take distorted output (cont'd) sp eakers are blown check system with known working speakers and repair or replace as needed poor bass response speakers wired wrong polarity causing cancellation at low frequencies check speaker polarity and repair as needed crossover set incorrectly reset crossovers referring to the multi-cross crossover configuration section of this manual for detailed instructions impedance load to amplifier too low check speaker impedance load,
Specifications 45/ & Z[ # RKP 0RQR Z[ # RKP 0RQR Z[ # RKP 0RQR Z 0$; 3RZHU 9DULDEOH +] G% /RZ 3DVV &URVVRYHU 9DULDEOH +] G% 6XEVRQLF &URVVRYHU 9DULDEOH G% +] %DVV %RRVW 7RWDO +DUPRQLF 'LVWRUWLRQ # RKP )UHTXHQF\ 5HVSRQVH +] 6LJQDO WR QRLVH 5DWLR G% ,QSXW 6HQVLWLYLW\ P9 9 'LPHQVLRQV Z[ K[ O 45/ & Z[ # RKP 0RQR Z[ # RKP 0RQR Z[ # RKP 0RQR Z 0$; 3RZHU 9DULDEOH +] G% /RZ 3DVV &URVVRYHU 9DULDEOH +]
