User Manual

ManualsBrandsSource Audio ManualsGuitar EffectsVertigo Tremolo - STEREO TREMOLO EFFECT WITH PEDAL FOR GUITAR

Table Of Contents

Welcome
Overview
Quick Start
- Power
- Guitar/Audio Connections
- Brief Knob, Footswitch, and Button Descriptions
Connections
- Input Side Connections
  - Input 1
  - Input 2
    - Input 2 as an Audio Input
    - Input 2 as a Neuro App Data Input
- Output Side Connections
  - Output 1
  - Output 2
    - Output 2 as an Audio Output
    - Output 2 as a Neuro App Data Daisy-Chain Output
- Example Neuro Daisy-Chain Connections
  - Mono Audio Path with Neuro Daisy-Chain
  - Mono-To-Stereo Audio Path with Neuro Daisy-Chain
- Power and Control Connections
Basic Tremolo Operation
Effect Types
- Normal (Optical)
- Harmonic
- Bias
- Additional Effect Types
Controls
- Knobs
- Effect Switch
- LEDs
  - Engage / Bypass LED
  - External Control LED
- Footswitch
- Control Input Button
Preset Storage and Recall
- Saving Your First Preset
- Editing a Preset
- Exiting Preset Mode
- Quick Preset Switching
Universal Bypass TM
Stereo Routing
Parametric EQ
- Low Cut Filter
External Control
- Expression Control
Neuro App
- Main Menu
- Sound Editor
- Browse Sounds
  - Open In Sound Editor
  - Deleting or Publishing Presets
- Hardware Options
- Neuro Hub (Formerly the Soundblox Hub)
  - MIDI
- USB
  - USB-MIDI
- External Tap Tempo
Specifications
- Dimensions
- Weight
- Power
- Audio Performance
Troubleshooting
- General
  - Factory Reset using the Neuro App
  - Factory Reset using the Hardware (Firmware v1.07 and later)
- Noise
- Hot Hand Doesn’t Work
- Unit Appears Dead / No LEDs Lit
Frequently Asked Questions
- How do I change the routing mode for my pedal without changing anything about the sounds?
- What kind of instruments can I connect to the Vertigo’s inputs?
- Can I power the Vertigo directly over USB, without using the 9 Volt supply?
- When connecting the Vertigo to a recording interface or mixer, should I used a Lo-Z (microphone) or Hi-Z (line / instrument) input?
- Why doesn’t the Vertigo respond to MIDI messages being sent to it?
- How do I enable extended effect types via MIDI?
- Can I use the Vertigo in my amp’s effects loop?
Rubber Feet
Waste Disposal Notes
Warranty
- Limited Transferrable Warranty
- Warranty Information
- Disclaimer and Limitation of Warranty
Version History

SA243 Vertigo Tremolo User’s Guide 14

Level Knob

Sets the overall output level of the Vertigo. The control is linear and ranges from 0 (completely silent)

to 2.0 (or +6 dB). At the middle position, the output gain is 1.0 (or 0 dB). The diagram below shows

the levels corresponding to the different knob positions, along with linear (red) and logarithmic

decibel (blue) equivalents.

Effect Switch

Selects between the three basic tremolo effect types – Normal (Optical), Harmonic, or Bias. These

effects are described in further detail in the Effect Types section.

LEDs

Engage / Bypass LED

The Engage / Bypass LED above the footswitch indicates if the tremolo effect is active (lit green) or

bypassed (not lit).

When the user preset mode is enabled, the LED will turn red. See the Preset Storage and Recall

section for more information about user presets.

External Control LED

The small LED located between the Depth and Speed knobs is the External Control LED. When lit, it

indicates that external control mode (expression, hot hand, or MIDI) is active. For more information,

see the External Control section.

Footswitch

Enables or bypasses the tremolo effect.

Control Input Button

This small button is used when configuring external control. See the External Control section for

more details.

0 dB

1.0

+6 dB

2.0

-∞ dB

-6 dB

0.5

+3.5 dB

1.5