MODEL : STm.117b MOBILE PRINTER Rev. 1.
Table of Contents 1. Unpacking 3 2. Product overview 4 3. Usage and Installation 5 3-1. Control panel usage 5 3-2. Battery Installation 6 3-3. Battery charging 7 3-4. Battery charger usage 8 3-5. Usage of Cigar Jack for charging 9 3-6. Roll paper installation 10 3-7. Leather case usage 11 3-8. Self test 12 4. Peripherals connection 13 4-1. Bluetooth connectiontion 13 4-2. Interface cable connection 14 5. Printer cleaning 15 6. Printer specification 16 6-1.
2. Product overview 1.
3. Usage and Installation 3-1 Control panel usage 3-2 Battery Installation Hook Button Name Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper Feed Button Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1.
3-3 Battery charging 3-4 Battery charger usage Optional Lamp Lamp DC Jack 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 3. Plug the power code to electrical outlet. 3-3-1 The status of lamp in charging Status charging charging complete Charging Lamp Red Green 1. Insert the battery into the battery holder as shown above 2. Connect the DC JACK to the power electrical outlet. 3. Plug the power code into the electrical outlet. 4.
3-5 Usage of Cigar Jack Charger for charging 3-6 Roll Paper installation Optional Printer Press the PUSH button to open the paper cover Insert the paper in the right direction 1 2 3 4 Battery holder Connect the car cigar JACK charger into the printer or battery holder. Input Output 12 ~ 24V 8.4V 0.8 ~ 1.2A NOTE Use the Cigar Jack offered by the manufacturer. 8 Pull a short length of paper out of the printer and close the cover. Tear off the additional paper using tear bar.
3-7 Leather case usage 3-8 Self Test Optional Open the leather case Place the printer into the leather case 1 2 3 Turn off the power pressing the power button for approximately 3 seconds. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3.
4. Peripherals connection The sample of self test printout This printer can communicate with Peripherals device via Bluetooth and cables. 4-1 Bluetooth Connection 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected.
5. Printer cleaning 4-2 Interface Cable Connection If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 1. Make sure to turn the printer power off prior to cleaning 2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement. 3.
6. Pritner Specification 6-1 Specification Printing Method Direct Thermal Battery type Li-ion Printing Speed 80mm/sec output 7.4V, 2200mAh 203 DPI X 203 DPI Charging time 3hours 40min W X D X H(mm) 149 X 161 X 69 W X D X H” 5.8 X 6.3 X 2.
7. CPCL Command Compatibility Graphics NOTE Compatible Compatible with only commanders provided by the manufacturer.
8.Certification Line Print Mode Compatibility SETLP ○ SETLF ○ Moving With X and Y Coordinates ○ LMARGIN ○ SETBOLD ○ SETSP ○ Special ASCII Characters ○ SETFF ○ SET-TOF ○ SETLP-TIMEOUT ○ FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation.
9. Setting up the software Please refer to the programming manual included in CD. CAUTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit. The device meets the FCC requirements for radio frequency (RF) radiation exposure in the standard body worn configuration with no minimum configuration.