User's Manual

ACCESS CONTROL SYSTEM
www.soyal.com
Instruction
V190627
AR-101US
Access Controller
3-5cm 1-3cm
1 Bi-color LED & 1 Beeper
NO
Read Only Read/Write
26±10
125kHz
(*Dual Band Available)
13.56MHz
EM Standard
9-24VDC
-20
。
C to +65
。
C
<1W
Black
AR-101US
Mini Proximity Reader
Support protocol
Reading Range
(Depending on tag or card)
Housing Material
Indicator
Ingress Protection
Color
Weight(g)
Frequency
Power Supply
Power Consumption
Read/Write
Operating Temperature
Keypad Material
37(L)X37(W)X31(H)Dimension(mm)
Communication
Interface
UART Protocol
WG Input
RS-485/9600 bps(N,8,1)
WG 26/34~64 (For WGKEYBOARD operation)
For WGKEYBOARD operation
(AR-WG-KEYBOARD)
ABS (Optional: Mounting Panel - DMET-PB/DPLA-PB)
MIFARE / DESFire / I Code
(ISO14443A / ISO7816-4)
Adding Tag
Deleting All Tags
Present Master Card
After 3 short beeps
[Access programming
mode]
After 3 short beeps
[Access programming
mode]
Present Master Card
Present the new card
or cards one by one
till finished the adding.
Present Master Card
[Exit programming mode]
1 long warning beep
after 2sec.
5 short beeps after
5sec: cards cleared
P.S. Once MASTER CARD is presented after one warning beep, all card data will be cleared.
1
3
2
39393232
3636
3535
8686
8686
6060
2121
70
115115
83
55
44
1010
Ø4.5
Ø4.5
45
MMET-PBC9H01 MMET-PBXXA01
MMET-PBXXA02
Installation
screw nut from behind
1
Use a screwdriver to screw
the plate to the wall
2
Paste the label sticker
3
Installation:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE:
Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfora ClassBdigital device,pursuanttoPart15oftheFCCRules.
Theselimitsare designedtoprovidereasonableprotectionagainstharmfulinterference ina residentialinstallation.Thisequipmentgenerates,usesandcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththe instructions, maycauseharmfulinterferencetoradiocommunications.
However, thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.
Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception, whichcanbedeterminedbyturningtheequipmentoffandon,theuseris encouragedtotry
to correct the interference by one or more of the followingmeasures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
--Connecttheequipmentintoanoutletonacircuitdifferent fromthattowhichthe receiverisconnected.
--Consultthedealeroranexperiencedradio/TVtechnicianfor help.
To maintain compliance with FCC’s RF Exposure guidelines, The 20cm is the minimum distance that has to be maintained between your body and the device.
FCC ID:2ACLEAR-101US