Wireless Module SparkLAN WNFB-265AXI(BT) & AP12275_M2P HW User manual Version 0.0 Revision History Date 2020/12/02 Revision Content Initial released Revised By Version Jason 0.
Wireless Module Contents 1. WNFB-265AXI(BT) & AP12275_M2P User manual Introduction.............................. 0 1.1. Module Block Diagram ..................................................................................... 0 1.2. Reference Design ............................................................................................ 1 2. WNFB-265AXI(BT) & AP12275_M2P EVB.................................................................. 5 List of Figures Figure1.
Wireless Module 1. WNFB-265AXI(BT) & AP12275_M2P User manual Introduction This document provides customers with considerations for the hardware design of WNFB265AXI(BT). It includes hardware block diagram, reference design, and PCB stack up, which will be explained in detail below. 1.1. Module Block Diagram Figure1. WNFB-265AXI(BT) & AP12275_M2P Module Block Diagram In Figure 1, WNFB-265AXI(BT) & AP12275_M2P is a fully Wi-Fi and Bluetooth functionalities 2230 M.2 card (KEY E) with integrated Bluetooth 5.
R6 30K 0201 R19 10K 0201/NC PCIE_CLKREQ_L PCIE_WAKEn C50 C49 0201/0.1uF 0201/0.1uF 0201/0 R 0201/0 R R112 R113 0201/0 R 0201/0 R C5 100pF 25V 0201 C2 100pF 25V 0201 PCIE_TDP PCIE_TDN PCIE_RDP R110 PCIE_RDN R111 PCIE_REFCLKP PCIE_REFCLKN VIO_3V3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 GND NC NC GND NC NC NC NC NC NC NC NC Key Key Key Key GND PERp0 PERn0 GND PETp0 PETn0 GND REFCLKP0 REFCLKN0 GND CLKREQ0# (3.3V) PEWake0# (1.
Wireless Module Figure2. Module Reference Design VIO R7 Connected to HOST I/O R7 used for keep-alive. NP/10K WL_REG_ON WLAN HOST_PCIE_RDP C121 0.1uF HOST_PCIE_RDN C122 0.
Wireless Module Figure4. PCI-e Interface Connection Diagram Figure5.
Wireless Module Figure6.
Wireless Module 2. WNFB-265AXI(BT) & AP12275_M2P EVB AUX ANT MAN ANT J20 J9 AP12275_M2P J16 CN2 J21 Gold Finger Figure7. Top view of WNFB-265AXI(BT) & AP12275_M2P EVB Interface highlights: 1. WNFB-265AXI(BT) & AP12275_M2P: Fully Wi-Fi and Bluetooth functionalities 2230 M.2 card. 2. J9: Mini USB interface connector for Bluetooth function control and measuring. 3. J16: Enable(H) or disable(L) Bluetooth, WiFi function. 4. J21: 3.3V for M.2 card main system power path. 5.
Wireless Module Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Wireless Module Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Unique antenna connector (RP-SMA) must be used on the Part 15 authorized transmitters used in the host product. Antenna Type Antenna Model Maximum Gain (dBi) 2.4 GHz 5GHz Dipole AD-103AG 2.02 dBi 2.
Wireless Module Industry Canada statement: This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: 1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Wireless Module bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l’exploitation point à point et non point à point, selon le cas. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Wireless Module libellé comme celui-ci: “ Contient IC: 6158A-NFB265AXIBT“. Plaque signalétique du produit final: Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6158A-NFB265AXIBT ". Manual Information To the End User: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
Wireless Module l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de montrer dans ce manuel.
