User's Manual

ManualsBrandsSparkLAN Communications ManualsElectronics802.11ac/b/g/n WiFi + Bluetooth M.2 Card

WNFQ-258ACN(BT)

Standard

IEEE802.11ac/a/b/g/n, Bluetooth V4.1,V4.0 LE, V3.0+HS, V2.1+EDR

Chipset solution

QCA6174A-5

Radio stream [Note1]

2T2R (Support WiFi/BT co-existence)

Antenna Type / con.

IPEX MHF4 connector

Bus Interface

WiFi: PCI Express

BT: USB

Form Factor

M.2 2230

Data Rate

WiFi:

802.11b: 11, 5.5, 2, 1 Mbps;

802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps

802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps

802.11n: MCS 0 to 15 for HT20MHz

MCS 0 to 15 for HT40MHz

802.11ac: MCS 0 to 9 for VHT20MHz

MCS 0 to 9 for VHT40MHz

MCS 0 to 9 for VHT80MHz

BT:

1 Mbps, 2Mbps and Up to 3Mbps EDR

Spreading /Modulation

Techniques

WiFi:

802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)

802.11b: DSSS (DBPSK, DQPSK, CCK)

802.11g: OFDM (BPSK,QPSK,16-QAM,64-QAM)

802.11n: OFDM (BPSK,QPSK,16-QAM,64-QAM)

802.11ac: OFDM (BPSK,QPSK,16-QAM,64-QAM, 256-QAM)

BT:

Header: GFSK

Payload 2M: 4-DQPSK

Payload 3M: 8-DPSK

Frequency Range [Note2]

WiFi:

11b/g/n: 2.412GHz ~ 2.484GHz

11ac/a/n: 5.15GHz ~ 5.85GHz

BT:

2.402GHz ~ 2.480 GHz

Transmit Output Power

(Tolerance: +/-2dBm)

5180

WiFi:

802.11a: 11dBm@54Mbps

802.11b: 19dBm@11Mbps

802.11g: 16dBm@54Mbps

802.11gn HT20: 16dBm@MCS7

Summary of content (10 pages)

PAGE 1
WNFQ-258ACN(BT) Standard IEEE802.11ac/a/b/g/n, Bluetooth V4.1,V4.0 LE, V3.0+HS, V2.1+EDR Chipset solution QCA6174A-5 Radio stream [Note1] 2T2R (Support WiFi/BT co-existence) Antenna Type / con. IPEX MHF4 connector Bus Interface Form Factor WiFi: PCI Express BT: USB M.2 2230 WiFi: 802.11b: 11, 5.5, 2, 1 Mbps; 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 15 for HT20MHz Data Rate MCS 0 to 15 for HT40MHz 802.
PAGE 2
802.11gn HT40: 15dBm@MCS7 802.11an HT20: 9dBm@MCS7 802.11an HT40: 9dBm@MCS7 802.11ac VHT80: 7dBm@MCS9 BT: (Class 2 Device) 0 ≤ Output Power ≤ +4 dBm WiFi: 802.11b: ≤-81dBm@11Mbps 802.11g: ≤-66dBm@54Mbps 802.11a: ≤-66dBm@54Mbps 802.11gn HT20: ≤-65dBm@MCS7 Receiver Sensitivity 802.11gn HT40: ≤-61dBm@MCS7 802.11an HT20: ≤-65dBm@MCS7 802.11an HT40: ≤-61dBm@MCS7 802.11ac VHT80: ≤-56dBm@MCS9 BT: < 0.1% BER at -70dBm Operating Voltage Power Consumption DC 3.
PAGE 3
NCC 警語本產品符合低功率電波輻射性電機管理辦法第十二條 ※經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條 (1) ※低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 -前項合法通信，指依電信法規定作業之無線電通信。 -低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。應避免影響附近雷達系統之操作。 (2) 高增益指向性天線只得應用於固定式點對點系統。此模組若安裝於其他平台時，該平台標籤需標明： (3) 此平台內建無線模組
PAGE 4
FCC Label Compliance Statement: (1) (2) (3) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 5
(4) End Product Labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: RYK-WNFQ258ACNBT ”. The (5) (6) grantee's FCC ID can be used only when all FCC compliance requirements are met.
PAGE 6
(7) End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: RYK-WNFQ258ACNBT”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
PAGE 7
(2) (2) Caution : (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
PAGE 8
(3) Le présent émetteur radio (IC: 6158A-258ACNBT) aété approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
PAGE 9
(1) This device is intended only for OEM integrators under the following conditions: (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and (2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 10
(3) Manuel d'information à l'utilisateur final: L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.