WNFT-237ACN(BT) ’ SparkLAN WNFT-237ACN(BT) M.2 ಬ Preliminary Version 2018/10/09 SparkLAN communication, Inc. 8F., No. 257, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan Tel.: +886-2-2659-1880. www.SparkLAN.
WNFT-237ACN(BT) ’ CONTENT ENVIRONMENTAL .......................................................................................................................... 3 OPERATING ............................................................................................................................................ 3 STORAGE................................................................................................................................................ 3 MTBF CACULATION .........
WNFT-237ACN(BT) ’ ENVIRONMENTAL Operating Operating Temperature: 0°C to +70 °C Relative Humidity: 5-90% (non-condensing) Storage Temperature: -40°C to +80°C (non-operating) Relevant Humidity: 5-95% (non-condensing) MTBF caculation Over 150,000hours
Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Unique antenna connector (IPEX) must be used on the Part 15 authorized transmitters used in the host product. Maximum Gain (dBi) Antenna Remark Antenna Model Type PCB 2.4 GHz 5GHz 3.13 dBi 4.94 dBi FML2.
Industry Canada statement: This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: 1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
pour l’exploitation point à point et non point à point, selon le cas. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Plaque signalétique du produit final: Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6158A-237ACNBT ". Manual Information To the End User: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
in end system. l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de montrer dans ce manuel.
WNFT-237ACN(BT) ’ Installing the Wireless PCIe M.2 module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first. A. Execute the “setup.exe”, Click “Next” to process the installation B.
WNFT-237ACN(BT) ’ C. Click Install this driver software anyway D. After step “C” please press Next button. E. Please click “YES” to install BT package.
WNFT-237ACN(BT) ’ J.
Un-installing the Wireless PCIe M.2 module Software A. Uninstall the WNFT-237ACN(BT) WLAN Driver from “Start”→ “All Programs”→ “REALTEK 11ac 8822CE PCIE WLAN NIC Massproduction kit” Please click “Uninstall” to remove WNFT-237ACN(BT) WLAN driver.
WNFT-237ACN(BT) User’s Manual Installing the Bluetooth USB Module Software A. Insert the M.2 card into system connector. B. Boot on system then the “Geniric Bluttooth Adapter” device will show up in device manager. C. Click right button on “RT Bluetooth Radio” and select “Update Driver”.
WNFT-237ACN(BT) User’s Manual D. After select “Update Driver Software ” then the Hardware Update Wizard will pop up, please select “Browse my computer for driver software” and press Next button. E. After step “D” please Select “Let me pick from a list of device drivers on my computer ”.
WNFT-237ACN(BT) User’s Manual F. Finish step “E” then select “Have Disk..” G. Now select browse to find the driver for device and press Next button.
WNFT-237ACN(BT) User’s Manual Page 21/22
WNFT-237ACN(BT) User’s Manual H. Then click “Install this driver software anyway” to continue. I. Press close button to complete the install process and you can see the Driver will be show up in Device Manager.
